Furniture of America CM3187SC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-11-21
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3187SC-2PK
Wrench
(Not Included)

Page 2 of 5

Parts List Hardware List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 2 pcs x 2
Front Leg
#A x 4 pcs x 2
Bolt 1/4”x3-1/4”
#B x 3 pcs x 2
Bolt 1/4”x1-1/2”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 4 pcs x 2
Hex Nut
MD
#D x 11 pcs x 2
Flat Washer
Page 3 of 5
#E x 11 pcs x 2
Lock Washer
#F x 1 pc
Allen Wrench
#G x 1 pc
Wrench
Note: The above parts and hardware are shown for a complete
assembly of ONE chair. However, the actual parts and hardware (with
an exception of the wrench andAllen wrench) in the box will be twice
the quantities listed to include the assembly of the second chair.
X 2

I. Place the backrest with legs (#1) on a protected surface.
II. Align the seat (#2) with the pre-drilled holes of the backrest with
legs (#1).
III. Prepare 3 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#B) and then the flat washer (#D) onto the
SAME bolt (#B), in that order.
IV. Insert the bolt assembly through the pre-drilled holes of the seat
(#2) and secure those bolts using the Allen wrench (#F) to lock
them with the backrest with legs (#1).
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 4 of 5
#B x 3 pcs
#D x 3 pcs
#E x 3 pcs
#A x 4 pcs
#D x 4 pcs
#E x 4 pcs
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#A) and then the flat washer (#D) onto the
SAME bolt (#A), in that order.
II. Insert the bolt assemblies through the pre-drilled holes in the
corners of the seat (#2) and secure those bolts using theAllen
wrench (#F) to lock them with the backrest with legs (#1).

I. Align the 2 front legs (#3) with
the pre-drilled holes on the
corners of the seat (#2).
II. Insert FIRST the flat washer
(#D) onto the threaded stud of
the front legs (#3) and then
the lock washer (#E) onto the
SAME stud, in that order.
Secure the hex nut (#C) onto
the same stud using the
wrench (#G) to tighten the
parts together.
Turn right (clockwise) to tighten
Page 5 of 5
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
Carefully place the completed chair in upright
position. Make sure the chair is rested on a
flat surface and does not feel loose or wobbly.
If it does, double check that the bolts/screws
are secured and properly tightened.
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR