Furniture of America cM4085S User manual

Page 1 of 15 Rev: 17-12-08
For more information contact our team: [email protected]

Page 2 of 15

To use Cam Lock
Fasteners:
Step 1 - Insert
Cam Pin into the
flat side of a
board. Tighten
only until snug. Do
not over-tighten.
Step 2 - Fit the
hole in the
edge of the
joining board
over the Cam
Pin. The head
of the Cam Pin
will be visible
in the large
hole in the side
of the joining
board, as in
Step 3.
Step 3 - Notice the Cam Lock has a “C”-shaped
back. An arrow on the front points the same
direction as the open section. Insert the Cam Lock
into the large hole so the opening of the “C” fits
over the head of the Cam Pin.
Step 4 - Use a flat screwdriver to turn the Cam Lock clockwise
one half a turn so it locks onto the head of the Cam Pin. Turn
only until it is snug – over-tightening could cause the Cam to
bend or break.
If it will not turn the full amount, turn the Cam Pin out (counter-
clockwise) one full turn, and try the Cam Lock again.
Cam Lock Cam Pin
Board A
Board B
flat side
edge to
join
Cam Lock Fastener Assembly
Cam Locks are fasteners used to join two boards
together, usually the edge of one board (A) to the
flat side of another board (B).
arrow
Open section of back
fits over the head of
the Cam Pin
head of the Cam Pin
Page 3 of 15

Page 4 of 15

Page 5 of 15

Page 6 of 15

Page 8 of 15
Attach dowels (#C) and cam bolts (#A) to the
holes of the rear left and right legs (#10,11).
Align left and right side panels (#5,6) to the cam
bolts (#A) and dowels (#C) of rear left and right
legs (#10,11). Secure by using cam locks (#B).
Attach dowels (#C) and cam bolts (#A) to the holes of the left and right side panels (#5,6). Align
front and rear crossbars (#3,4) to the cam bolts (#A) and dowels (#C) of left and right side panels
(#5,6). Secure by using cam locks (#B).

Page 9 of 15
Attach dowels (#C) and cam bolts (#A) to the holes of the bottom panel (#2). Align
bottom support panels (#12) to the cam bolts (#A) and dowels (#C) of bottom panel
(#2). Secure by using cam locks (#B).
Attach cam bolts (#A) to the holes of the rear left and right legs (#10,11). Align bottom support panels
(#12) to the cam bolts (#A) of rear left and right legs (#10,11). Secure by using cam locks (#B).

Page 10 of 15
Attach dowels (#C) and cam bolts (#A) to the holes of the front left and right legs (#8,9). Align front
left and right legs (#8,9) to the holes of the product. Secure by using cam locks (#B).
Align divider panel (#7) to the holes of the crossbars (#3,4).
Secure by using screws (#F).
Slightly hammer in the floor protectors (#J)
to the legs.

Reattach the drawer rails to the side panels (#5,6).
Slide back panel (#13) through the thin gaps.

Page 12 of 15
Attach cam bolts (#A) to the holes of the top panel (#1).
Attach dowels (#C) to the holes of the top panel (#1). Align top panel (#1) to the base of the
product. Secure by using cam locks (#B), then cover cam locks (#B) by using stickers (#I).

Page 13 of 15
Attach handles (#G) to the front drawer panels (#14,15) by using
bolts and washers (#H).
Align drawer side panels (#16,17) to the holes of the drawer back (#18).
Secure by using screws (#F).

Page 14 of 15
Slide the bottom panel (#19) through the thin lined gaps of the drawer panels.
Attach cam bolts (#D) to the holes of the front drawer panels (#14,15). Align front drawer panels
(#14,15) to the holes of the drawer, then secure by using cam locks (#E).

Page 15 of 15
ASSEMBLY COMPLETED