Furniture of America CM4321S User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Page 1 of 9
DIFFICULT
ASSEMBLY RATING
CM4321S
Phillips Screwdriver
(Not Included)
2 PERSONS RECOMMENDED
Rev: 18-10-22

Page 2 of 9

Page 3 of 9
Parts List Hardware List (Continued)
#1 x 1 pc
Table Top
#2 x 2 pcs
Leg A
#3 x 2 pcs
Leg B
#D x 8 pcs
Lock Washer 5/16”
#4 x 1 pc
Leg Support
#5 x 2 pcs
Bottom Shelf ( L& R)
#E x 1 pc
Allen Wrench M5
#F x 4 pcs
Bracket
#G x 8 pcs
Bolt 1/4”x7/8”
#H x 8 pcs
Flat Washer 1/4”
#I x 8 pcs
Lock Washer 1/4”
#6 x 1 pc
Glass Top
Hardware List
#A x 8 pcs
Bolt 5/16”x7/8”
#B x 8 pcs
Flat Bolt 5/16”x7/8”
#C x 8 pcs
Flat Washer 5/16”
#J x 1 pc
Allen Wrench M4
#K x 2 pcs
L Bracket
#L x 8 pcs
Shelf Support
#M x 1 pc
Left L Bracket
#N x 1 pc
Right L Bracket

Align the bracket (#F) with the pre-drilled holes on each of the leg A
(#2) AND each of the leg B (#3). Insert 8 flat bolts (#B) into the
brackets (#F) using the Allen wrench (#E) to lock them in with the
two leg A (#2) AND the two leg B (#3).
Turn right (clockwise) to tighten
Page 4 of 9
#B x 8 pcs
#F x 4 pcs
Turn right (clockwise) to tighten
#G x 8 pcs
#H x 8 pcs
#I x 8 pcs
#K x 2 pcs
#M x 1 pc
#N x 1 pc
X 2 X 2
I. Prepare 8 bolt assemblies by inserting
FIRST the lock washer (#I) onto the bolt
(#G) and then the flat washer (#H) onto
the SAME bolt (#G), in that order.
II. Align the long side of the L brackets (#K),
the long side of the left L bracket (#M) and
the long side of the right L bracket (#N)
with the pre-drilled holes on the leg
support (#4). Insert 4 bolt assemblies
through the long side of L brackets and
secure those bolts using the Allen wrench
(#J) to lock them with the leg support (#4).
III. Align the short side of the L brackets (#K)
assembled on the leg support (#4) with the
pre-drilled holes on the two leg A (#2).
Insert 2 bolt assemblies through the short
side of L brackets (#K) and secure those
bolts using the Allen wrench (#J) to lock
them with the two leg A (#2).
IV. Align the short side of the left L bracket
(#M) and the right L bracket (#N) with the
pre-drilled holes on the two leg B (#3).
Insert 2 bolt assemblies through the short
side of L brackets (#K) and secure those
bolts using the Allen wrench (#J) to lock
them with the two leg B (#3).

I. Carefully place the table top (#1)
facing down on a protected surface.
II. Align the brackets (#F) assembled on
the leg A (#2) AND the leg B (#3) with
the pre-drilled holes on the bottom of
the table top (#1).
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer (#D)
onto the bolt (#A) and then the flat
washer (#C) onto the SAME bolt (#A),
in that order.
IV. Insert the bolt assemblies through the
pre-drilled holes on the brackets (#F)
and secure those bolts using the Allen
wrench (#E) to lock them with the
table top (#1).
Page 5 of 9
Turn right (clockwise) to tighten
#A x 8 pcs
#C x 8 pcs
#D x 8 pcs
Insert 8 shelf supports (#L) into the pre-drilled holes of
the leg A (#2), the leg B (#3) and the leg support (#4).
#L x 8 pcs
#3
#2 #3
#2
#2
#3 #3
#4
#2

Page 6 of 9
ASSEMBLY IS COMPLETED
Place the bottom shelves (#5R/L)over the shelf supports
(#L). Make sure the bottom shelves (#5R/L) are rested
and leveled on top of all the shelf supports (#L).
Carefully place the glass top (#6) onto the table top (#1).
Make sure the table is rested on a flat surface and it
does not feel loose or wobbly. If it does, double check
that the bolts are secured and properly tighten.
#1
#5R
#5L
#6

Parts List Hardware List
#1 x 1 pc
Seat Cushion
#2 x 1 pc
Seat Frame
#3 x 1 pc
Base
#A x 6 pcs
Bolt 5/16”x1-3/4”
#B x 6 pcs
Lock Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 6 pcs
Flat Washer
MD
#D x 1 pc
Allen Wrench
#4 x 1 pc
Center Leg
Page 7 of 9
#E x 4 pcs
Screw
#5 x 2 pcs
Side Leg

Turn right (clockwise) to tighten
Page 8 of 9
#A x 3 pcs
#B x 3pcs
#C x 3 pcs
Turn right (clockwise) to tighten
Align the seat cushion (#1) onto the top of the seat
frame (#2). Tighten 4 screws (#E) through the bottom of
the seat frame (#2) using the Phillips screwdriver to
secure them with the seat cushion (#1).
#E x 4 pcs
I. Insert the center leg (#4) and
the two side legs (#5) into the
seat frame (#2).
II. Prepare 3 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then
the flat washer (#C) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies
through the pre-drilled holes on
the seat frame (#2) and secure
those bolts using the Allen
wrench (#D) to lock them in
with the center leg (#4) and the
two side legs (#5).
#2

I. Insert the center leg (#4) and the two
side legs (#5) into the base (#3).
II. Prepare 3 bolt assemblies by inserting
FIRST the lock washer (#B) onto the
bolt (#A) and then the flat washer (#C)
onto the SAME bolt (#A), in that order.
III. Insert the bolt assemblies through the
pre-drilled holes on the base (#3) and
secure those bolts using the Allen
wrench (#D) to lock them in with the
center leg (#4) and the two side legs
(#5).
Page 9 of 9
Turn right (clockwise) to tighten
ASSEMBLY IS COMPLETED
#A x 3 pcs
#B x 3 pcs
#C x 3 pcs
Make sure the chair is rested on a flat surface and it does
not feel loose or wobbly. If it does, double check that the
bolts/screws are secured and properly tighten.
#4
#5 #5