Furniture of America ID-10339 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For most
products, two persons are recommended.
ID-10339
ASSEMBLY INSTRUCTIONS
Tools Required for Assembly:
Rev.14-07-09
Page 1 of 13
DIFFICULT
ASSEMBLY RATING
Phillips Screwdriver (Not Included)
2 PERSONS RECOMMENDED
Hammer (Not Included)

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 13

Page 3 of 13

Page 4 of 13
Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following:
1. Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure you have enough space to move around during
the assembly. ALWAYS have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2. To protect from damage, assemble the item on a clean, protective surface,
such as on a carpet or cardboard.
3. Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging material until assembly is completed.
4. Make sure all parts and hardware are accounted for by comparing the actual
parts and hardware to the list provided in the assembly instructions. Also
check for any irregularity such as crack, flaw or improperly drilled hole. If there
is any problem or missing piece, please contact the manufacturer or the
supplier. Please have the model number, part number and a brief description
of the problem ready will help expedite the replacement process.
5. Read the entire instruction manual and view the diagrams first before
assembling. Arrange your parts in order of use and group the identical
hardware together to make it easier to grab each piece as you begin to
assemble.
6. During the assembly process, make sure all parts are properly aligned before
tightening with the tool provided or required for the assembly. Do not use
power tools and do not over tighten.
7. When applying glue to the wood dowels to bond the parts together, please be
ABSOLUTELY certain that the parts are correct and lined up with each other
(refer to diagrams and take notice of the various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.
PRE-ASSEMBLY INTRODUCTION

Page 5 of 13
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
ly

Page 6 of 13
Before you begin, please read “Assembly and
Care Advice”, “Pre-Assembly Introduction” and
“Cam Lock Fastener Assembly Instructions”.
PARTS LIST

Page 7 of 13
HARDWARE LIST
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.

Page 8 of 13
A
ASSEMBLY INSTRUCTIONS

Page 9 of 13
ASSEMBLY INSTRUCTIONS

Page 10 of 13
A
ASSEMBLY INSTRUCTIONS