Furniture of America CM7056-Q User manual

Rev: 16-07-01

Turn right (clockwise) to tighten
Page 4 of 6
Enlarged
#C x 8 pcs
#D x 8 pcs
#E x 8 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.
I. Align the feet (#5) onto the pre-drilled holes on the bottom corners
of the headboard (#1).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#C) and then the flat washer (#D) onto the
SAME bolt (#C), in that order.
III. Insert the bolt assemblies through the holes of the feet (#5) and
secure those bolts using the Allen wrench (#H) to lock them in with
the headboard (#1).
IV. Repeat the process above to assemble the feet (#5) onto the
footboard (#3).

Turn right (clockwise) to tighten
Page 5 of 6
Enlarged
Enlarged
#A x 8 pcs
#D x 8 pcs
#E x 8 pcs
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
I. Prepare 4 bolt assemblies by inserting
FIRST the lock washer (#E) onto the
bolt (#A) and then the flat washer (#D)
onto the SAME bolt (#A), in that order.
II. Insert two bolt assemblies through the
right and left side of the pre-drilled
holes of the headboard (#1) using the
Allen wrench (#H) but expose about
½ of the bolts threads.
III. Mount the brackets of the side rails
(#2) onto the bolts (#A) on each side
of the headboard (#1). Make sure all
the washers are in the FRONT of the
brackets. Use the Allen wrench (#H)
to tighten the bolts with the two parts
together.
IV. Repeat the process I through III above
to assemble the other ends of the side
rails (#2) onto the footboard (#3).
.
I. Align the two slat support legs (#7) with the pre-drilled holes of the support
rail (#4).
II. Prepare 2 bolt assemblies by inserting FIRST the lock washer (#E) onto the
bolt (#B) and then the flat washer (#D) onto the SAME bolt (#B), in that
order.
III. Insert the two bolt assemblies through the pre-drilled holes of the support
rail (#4) using the Allen wrench (#H) to lock them in with the slat support
legs (#7).
Turn right (clockwise) to tighten

Turn right (clockwise) to tighten
Page 6 of 6
Enlarged
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
I. Align the support rail (#4)
with the pre-drilled holes on
the center of the headboard
(#1) and the footboard (#3).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#E) onto the bolt
(#B) and then the flat washer
(#D) onto the SAME bolt
(#B), in that order.
III. Insert the 4 bolt assemblies
through the brackets of the
support rail (#4) using the
Allen wrench (#H) to lock
them in with the headboard
(#1) and the footboard (#3).
I. Prepare a complete bed slat
by inserting one center
plastic connector (#F) onto
the ends of two bed slats
(#6). Then connect two end
caps (#G) onto the other
ends of the bed slats (#6).
II. Align the end caps (#G) with
the pre-drilled holes on
each side of the side rails
(#2) and snap both ends to
lock in place. Then snap
the center plastic connector
(F) onto the central support
rail (#4).
III. Repeat the above process
for the remaining bed slats.
ASSEMBLY IS COMPLETED
Note: The correct position of the bed
slats should be arcing UPWARD when
placing on the rails.
#F x 15 pcs
#G x 30 pcs

Rev: 16-07-01

Turn right (clockwise) to tighten
Page 4 of 6
Enlarged
#C x 8 pcs
#D x 8 pcs
#E x 8 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.
I. Align the feet (#5) onto the pre-drilled holes on the bottom corners
of the headboard (#1).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#C) and then the flat washer (#D) onto the
SAME bolt (#C), in that order.
III. Insert the bolt assemblies through the holes of the feet (#5) and
secure those bolts using the Allen wrench (#H) to lock them in with
the headboard (#1).
IV. Repeat the process above to assemble the feet (#5) onto the
footboard (#3).