Furniture of America CM4777-3PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-04-23
Page 1 of 8
DIFFICULT
ASSEMBLY RATING
CM4777-3PK

Page 2 of 8

Parts List Hardware List
#1 x 1 pc
Glass Top
#2 x 4 pcs
Leg
#3 x 1 pc
Base
#A x 8 pcs
Bolt M6x12
#B x 4 pcs
Suction Cup
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 1 pc
Allen Wrench
MD
#D x 4 pcs
Glide
#4 x 1 pc
Leg Support
Page 3 of 8

#A x 4 pcs
#D x 4pcs
Align the legs (#2) with the pre-drilled holes on the base
(#3). Insert a bolt (#A) through each of the legs (#2) and
secure those bolts using the Allen wrench (#C) to lock them
in with the base (#3).
Turn right (clockwise) to tighten
Page 4 of 8
#A x 4 pcs
I. Align the leg support (#4)
with the pre-drilled holes on
the center of the legs (#2).
II. Insert 4 bolts (#A) through
the pre-drilled holes on the
leg support (#4) and secure
those bolts using the Allen
wrench (#C) to lock them in
with the legs (#2).
III. Align the threaded end of
the glides (#D) with the pre-
drilled holes on the bottom
of the legs (#2) and tighten
by hand until secured.
Turn right (clockwise) to tighten

Insert 4 suction cups (#B) into the base (#3).
Page 5 of 8
#B x 4 pcs
ASSEMBLY IS COMPLETED
Carefully place the glass top (#1) over the suction cups (#B).
Make sure the table is rested on a flat surface and it does not
feel loose or wobbly. If it does, double check that the bolts are
secured and properly tighten. If needed, adjust the glides
according to the ground level.
Adjust the glide (#D) according to the
ground level. To lower or to raise, you
need to turn the glide (#D) clockwise or
counterclockwise, respectively.

Parts List Hardware List
#1 x 1 pc x 2
Glass Top
#2 x 4 pcs x 2
Leg
#3 x 1 pc x 2
Base
#A x 8 pcs x 2
Bolt M6x12
#B x 4 pcs x 2
Suction Cup
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 1 pc x 2
Allen Wrench
MD
#D x 4 pcs x 2
Glide
#4 x 1 pc x 2
Leg Support
Page 6 of 8
X 2
Note: The above parts and hardware are shown
for a complete assembly of ONE table.
However, the actual parts and hardware in the
box will be twice the quantities listed to include
the assembly of the second table.

#A x 4 pcs
#D x 4 pcs
Align the legs (#2) with the pre-drilled holes on the base
(#3). Insert a bolt (#A) through each of the legs (#2) and
secure those bolts using the Allen wrench (#C) to lock them
in with the base (#3).
Turn right (clockwise) to tighten
Page 7 of 8
#A x 4 pcs
I. Align the leg support (#4)
with the pre-drilled holes on
the center of the legs (#2).
II. Insert 4 bolts (#A) through
the pre-drilled holes on the
leg support (#4) and secure
those bolts using the Allen
wrench (#C) to lock them in
with the legs (#2).
III. Align the threaded end of
the glides (#D) with the pre-
drilled holes on the bottom
of the legs (#2) and tighten
by hand until secured.
Turn right (clockwise) to tighten

Insert 4 suction cups (#B) into the base (#3).
Page 8 of 8
#B x 4 pcs
ASSEMBLY IS COMPLETED
Carefully place the glass top (#1) over the suction cups (#B).
Make sure the table is rested on a flat surface and it does not
feel loose or wobbly. If it does, double check that the bolts are
secured and properly tighten. If needed, adjust the glides
according to the ground level.
Adjust the glide (#D) according to the
ground level. To lower or to raise, you
need to turn the glide (#D) clockwise or
counterclockwise, respectively.
ASSEMBLE EVERYTHING EXACTLY THE
SAME FOR THE SECOND TABLE