Furniture of America Perry Round Geometric Coffee Table YNJ-129-6 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For most
products, two persons are recommended.
ASSEMBLY INSTRUCTIONS
Tools Required for Assembly:
Page 1 of 11
DIFFICULT
ASSEMBLY RATING
(Not Included)
2 PERSONS RECOMMENDED
Phillips Screwdriver
Allen Wrench (Included)
(Not Included)
Hammer

Thank you for your purchase!
Page 2 of 11
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.

Page 3 of 11

Page 4 of 11
Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following:
1. Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure you have enough space to move around during
the assembly. ALWAYS have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2. To protect from damage, assemble the item on a clean, protective surface,
such as on a carpet or cardboard.
3. Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging material until assembly is completed.
4. Make sure all parts and hardware are accounted for by comparing the actual
parts and hardware to the list provided in the assembly instructions. Also
check for any irregularity such as crack, flaw or improperly drilled hole. If there
is any problem or missing piece, please contact the manufacturer or the
supplier. Please have the model number, part number and a brief description
of the problem ready will help expedite the replacement process.
5. Read the entire instruction manual and view the diagrams first before
assembling. Arrange your parts in order of use and group the identical
hardware together to make it easier to grab each piece as you begin to
assemble.
6. During the assembly process, make sure all parts are properly aligned before
tightening with the tool provided or required for the assembly. Do not use
power tools and do not over tighten.
7. When applying glue to the wood dowels to bond the parts together, please be
ABSOLUTELY certain that the parts are correct and lined up with each other
(refer to diagrams and take notice of the various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.
PRE-ASSEMBLY INTRODUCTION

Page 5 of 11
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
ly

ASSEMBLY INSTRUCTIONS
Hardware ③x 4 pcs
Hardware ④x 2 pcs
Page 7 of 11
I. Insert the two long wood dowels
(#4) through Part #D until they
are centered. Then insert the
two Part #E onto each ends of
the long wood dowels (#4)
forming an “X”.
II. Insert 2 short wood dowels (#3)
into Part #D and 1 each short
wood dowel (#3) into Part #E.
Applying glue to the wood dowel:
a). Remove one end of the dowel and
squeeze a drop of glue onto it. The glue
should cover the tip of the dowel. DO
NOT pour glue directly into the hole.
b). Insert the glued end of the dowel into
its appropriate location. Use a rag or a
paper towel to wipe any excess glue
oozing around the dowel.
c). Squeeze a drop of glue onto the end
of the dowel sticking out. The glue should
cover the tip of the dowel.
d). Insert this end of the dowel into the
other part. Use a rag or a paper towel to
wipe any excess glue oozing around the
dowel.
e). Both parts should now line up and
connected.
Hardware ①x 4 pcs
Turn right (clockwise) to tighten

ASSEMBLY INSTRUCTIONS
Hardware ①x 4 pcs
Page 8 of 11
Hardware ②x 4 pcs
I. Insert the 4 cam connectors (#2)
into the holes of Part #E and #D.
Make sure each cam connector
(#2) is position correctly with the
arrow pointing to the small
drilled hole. Please refer to
“Cam Lock Fastener Assembly
Instructions” for detailed
instructions.
II. Gently place Part #D and #E so
that the cam bolts/screws (#1)
are inside the cam connectors
(#2).
III. Use a Phillips screwdriver, to
tighten each cam connector (#2)
by turning right until it is locked
with the cam bolts/screws (#1).
The parts should fit snugly with
each other.
Ⓐ
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten

ASSEMBLY INSTRUCTIONS
I. Insert the two long wood
dowels (#4) through Part
#F until they are
centered. Then insert
the two Part #G onto
each ends of the long
wood dowels (#4)
forming an “X”.
II. Insert 2 short wood
dowels (#3) into Part #F
and 1 each short wood
dowel (#3) into Part #G.
Hardware ③x 4 pcs
Hardware ④x 2 pcs
Hardware ②x 4 pcs
Page 9 of 11
Follow the cam instructions from Step 3.
Follow the glue
instructions from Step 2.
Turn right (clockwise) to tighten

ASSEMBLY INSTRUCTIONS
Hardware ⑧x 4 pcs
Page 10 of 11
Center the glide (#8) on the bottom of the longer end of
Part #B and gently tap with the hammer until the glide is
secured all the way in. Repeat the process to assemble
the remaining glides (#8) onto Part #B.
Hardware ⑤x 8 pcs I. This final step requires the assistant of
another person. Align the shorter end
of Part #B with the pre-drilled hole on
the ends of Part #D.
II. Using the Allen wrench (#6), secure the
screw (#5) only enough to stabilize and
hold the two parts together. DO NOT
TIGHTEN YET. Repeat the process to
assemble the remaining shorter ends of
Part B onto Part #D and #E.
III. Have one person holding the
assembled Part #F to align with the pre-
drilled hole on the longer end of Part
#B.
IV. Using the Allen wrench (#6), secure the
screw (#5) only enough to stabilize and
hold the two parts together. DO NOT
TIGHTEN YET. Repeat the process to
assemble the remaining longer ends of
Part B onto Part #F and #G.
V. Go back and fully tighten all 8 screws
(#5).
⑥
Ⓖ
ⒹⒺ
Ⓔ
ⒻⒼ
Turn right (clockwise) to tighten