Furniture of America Mandeville CM7986Q User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-25
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM7986Q
Phillips Screwdriver (Not Included)

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 1 pc
Left Leg
#3 x 1 pc
Right Leg
#A x 6 pcs
Screw
#B x 10 pcs
Bolt 5/16”x2”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 14 pcs
Lock Washer
MD
#D x 14 pcs
Flat Washer
#4 x 1 pc
Bottom Rail
Page 3 of 6
#E x 4 pcs
Bolt 5/16”x1-1/2”
#F x 1 pc
Allen Wrench
#5 x 1 pc
Footboard
#6 x 2 pcs
Side Rail
#7 x 3 pcs
Slat
#8 x 3 pcs
Slat Support Leg

I. Align the bracket of the left leg (#2) with the pre-drilled holes
of the headboard (#1).
II. Prepare 5 bolt assemblies by inserting FIRST the lock
washer (#C) onto the bolt (#B) and then the flat washer (#D)
onto the SAME bolt (#B), in that order.
III. Insert the 5 bolt assemblies through the bracket of the left leg
(#2) and secure those bolts using the Allen wrench (#F) to
lock them in with the headboard (#1).
IV. Repeat the process for the assembly of the right leg (#3) onto
the headboard (#1).
Turn right (clockwise) to tighten
Page 4 of 6
#B x 10 pcs
#C x 10 pcs
#D x 10 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
of the product and to avoid any potential injury and/or
damage.
Enlarged
Note: Right and left are determined by standing in
FRONT of the headboard.

Page 5 of 6
Attach the side rails (#6) with the hooks fully inserted into the
headboard (#1)AND the footboard (#5).
Turn right (clockwise) to tighten
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
I. Align the bottom rail (#4) with the
pre-drilled holes on the back of the
headboard (#1).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#E) and then the
flat washer (#D) onto the SAME bolt
(#E), in that order.
III. Insert the 4 bolt assemblies through
the bottom rail (#4) and secure
those bolts using the Allen wrench
(#F) to lock them in with the
headboard (#1).
Enlarged
Enlarged

Page 6 of 6
Align the ends of the assembled slat (#7) with the pre-drilled
holes on each side of the side rails (#6). Secure two screws
(#A) onto each end of the slat (#7) by using a Phillips
screwdriver to tighten them down to the bed rails. Repeat the
process for the remaining two slats (#7).
Turn right (clockwise) to tighten
#A x 6 pcs
Align the threaded end of the slat support leg (#8) with the
pre-drilled hole of the slat (#7) and tighten by hand until
secured. Repeat the process for attaching the remaining two
slat support legs (#8) onto the two slats (#7).
Enlarged
ASSEMBLY IS COMPLETED
Adjust the leveler according to the ground
level. To lower or to raise the support leg,
you need to turn the leveler clockwise or
counterclockwise, respectively.

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-25
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM7986CK CM7986EK
Phillips Screwdriver (Not Included)

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Headboard
#2 x 1 pc
Left Leg
#3 x 1 pc
Right Leg
#A x 8 pcs
Screw
#B x 10 pcs
Bolt 5/16”x2”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 14 pcs
Lock Washer
MD
#D x 14 pcs
Flat Washer
#4 x 1 pc
Bottom Rail
Page 3 of 6
#E x 4 pcs
Bolt 5/16”x1-1/2”
#F x 1 pc
Allen Wrench
#5 x 1 pc
Footboard
#6 x 2 pcs
Side Rail
#7 x 4 pcs
Slat
#8 x 8 pcs
Slat Support Leg

I. Align the bracket of the left leg (#2) with the pre-drilled holes
of the headboard (#1).
II. Prepare 5 bolt assemblies by inserting FIRST the lock
washer (#C) onto the bolt (#B) and then the flat washer (#D)
onto the SAME bolt (#B), in that order.
III. Insert the 5 bolt assemblies through the bracket of the left leg
(#2) and secure those bolts using the Allen wrench (#F) to
lock them in with the headboard (#1).
IV. Repeat the process for the assembly of the right leg (#3) onto
the headboard (#1).
Turn right (clockwise) to tighten
Page 4 of 6
#B x 10 pcs
#C x 10 pcs
#D x 10 pcs
Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
of the product and to avoid any potential injury and/or
damage.
Enlarged
Note: Right and left are determined by standing in
FRONT of the headboard.