Furniture of America CM7365Q User manual

Page 1 of 7
Assembly Instructions
EASY DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Rev: 18-09-17
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
For more information contact our team: [email protected]
CM7365Q
Allen Wrench
(Included)
(Not Included)
Phillips Screwdriver
Wrench
(Included)

Page 2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 7
#I x 10pcs
Screw #4 x 30mm
#2 x 2pcs
Headboard Leg(L&R)
#1 x 1pc
Headboard
#3 x 2pcs
Side Rails
Parts List Hardware List
#6 x 2pcs Ø5/16"
Drawer Support Leg 120x30x30mm
#B x 14pcs
Lock Washer Ø5/16"
#C x 14pcs
Flat Washer Ø5/16"
#D x 1pc
Allen Key M4
#A x 6pcs
Bolt Ø5/16" x 1-3/8"
#4 x 1pc
Storage Footboard
#5 x 1set
Slat 13pcs
#7 x 6pcs Ø5/16"
Slat Support Leg 365x30x30mm
#G x 8pcs
Hex Nut Ø5/16"
#F x 8pcs
Half Moon Washer Ø5/16"
#E x 8pcs
Thread Rod Ø5/16" x 3-1/2"
#H x 1pc
Wrench 12mm
#8 x 1pc
Dusty Panel
#J x 6pcs
Screw #4 x 10mm

Page 4 of 7
#D
#A
#B
#C
#A x 6pcs
#B x 6pcs
#C x 6pcs
#2R
#2L
#1
Exploded View
#1
#2R
#2L
#5
#3
#3
#4
#6
#8
#7
Align HB legs (#2R/L) to the headboard (#1), then
secure by using bolts (#A) with washers (#B,C).

Page 5 of 7
#4
#6
#B x 8pcs
#C x 8pcs
#E x 8pcs
#F x 8pcs
#G x 8pcs
#1
#4
#3
#3
#E
#B
#C
#G
#F #H
Attach support legs (#6) to the footboard (#4). Adjust the leveler
on the support legs (#6) according to ground level.
Attach threaded bolts (#E) to the headboard (#1) and footboard (#4), then align side
rails (#3) to the threaded bolts (#E) of the headboard (#1) and footboard (#4).
Secure by using half moon washers (#F), washers (#B,C), and hex nuts (#G).

Page 6 of 7
#I x 10pcs
#I
#7
#5
#3
#3
#5
Attach support legs (#7) to the slat kit (#5), then adjust levelers on the support
legs (#7) according to ground level.
Align slat kit (#5) to the side rails (#3), then secure by using screws (#I).

Page 7 of 7
ASSEMBLY IS COMPLETED
#J x 6pcs
#J
#8
#5
Place dusty panel (#8) to the bottom end of the slats (#5), then secure
by using screws (#J).
Remove handles from the
inside of drawers, then secure
handles to the outside of
drawers.

Page 1 of 8
Assembly Instructions
EASY DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Rev: 18-09-17
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
For more information contact our team: [email protected]
CM7365CK
Allen Wrench
(Included)
(Not Included)
Phillips Screwdriver
Wrench
(Included)

Page 2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 8
Parts List Hardware List
#7 x 12pcs Ø5/16"
Slat Support Leg 365x30x30mm
#8 x 1pc
Dusty Panel
#2 x 2pcs
Headboard Leg(L&R)
#1 x 1pc
Headboard
#3 x 2pcs
Side Rails
#6 x 2pcs Ø5/16"
Drawer Support Leg 120x30x30mm
#4 x 1pc
Storage Footboard
#5 x 1set
Slat 13pcs
#A x 6pcs
Bolt Ø5/16" x 1-3/8"
#B x14pcs
Lock Washer Ø5/16"
#C x 14pcs
Flat Washer Ø5/16"
#D x 1pc
Allen Key M4
#G x 8pcs
Hex nut Ø5/16"
#F x 8pcs
Half Moon Washer Ø5/16"
#E x 8pcs
Thread Rod Ø5/16" x 3-1/2"
#H x 1pc
Wrench 12mm