Furniture of America FGI-2090C25 User manual

VERSION # 20-06-12
The Assembly Rating is a
5-point system showing the
level of effort needed to
assemble a specific product.
ASSEMBLY RATING
EASY DIFFICULT
Hammer
(Not Included)
(Not Included)
Philips
Screwdriver
TOOLS REQUIRED
2 - People
Recommended
Furniture of America
E-Commerce by Enitial Lab
MODEL #
GIVE US A CALL: 1-888-980-5122
MON – FRI 8:30AM – 5:30PM (PST)
Questions?
1 / 12
FGI-2090C25
FGI-2090C35

Thank you for your purchase!
We hope you enjoy this new addition to your home for many years to come.
Our commitment to providing quality products does not simply end when you purchase
our product. We fully stand behind our products from start to finish. Our customer
service department is available Monday – Friday 8:30 AM – 5:30 PM Pacific and can
help with assembly questions as well as, if necessary, replacing damaged or missing
parts. To help expedite our service, please have these assembly instructions readily
available, along with your order receipt.
E-MAIL
[e-mail]
Furniture America
E-Commerce by Enitial Lab
WEBSITE
www.foagroup.com
FOA Intro
FurnitureOfAmerica
foagroup
Monday to Friday
8:30AM- 5:30PM (PST)
Consumer Hotline
Toll-Free 1-888-980-5122
of
Prep Time!
Please review the assembly instructions and all
diagrams prior to assembling. Arrange parts as
recommended on Page 7 and group identical
hardware together to make assembling easier.
Check out our Quick Tips!
We recommend reviewing the pre-assembly
handouts. Even experts need a refresher now and
then!
Are you missing anything?
Double-check all parts, hardware and
accessorieslisted on Page 6 are
accounted for.
Should we send any replacements?
Are there any irregularities or flaws in the
parts? We can send replacements!
CHECK
BEFORE STARTING
2 / 12

PRE ASSEMBLY
INTRODUCTION
Suitable Location
Assembling near the area of the
intended location is highly
recommended.
Avoid Scratches
Use cardboard, blankets or a
carpeted area while assembling
furniture to prevent scratches.
Teamwork
ALWAYS have at least two people
to help with transporting and
assembling the product to avoid
potential injury and/or damage.
Flat Surface
Make sure the furniture rests on
a flat and level surface with each
leg evenly touching the floor.
Sufficient Space
Make sure you have enough
space to move around during the
assembly.
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.
3 / 12

IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE HARDWARE MAY LOOSEN
OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS
INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY.
Turn clockwise to tighten and
only tighten when step is
completed or when instructed
to do so.
Use the appropriate hand tools
or power tools for assembly.
Select steps, such as tightening
screws and/or bolts, may require
hand tools to avoid causing
damage during assembly.
Position each part correctly
and insert screws or bolts into
their respective holes.
Save the instructions and store
any supplied tools for later
maintenance.
After two weeks, check and
tighten any loose hardware and
repeat again every six months
thereafter.
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
ASSEMBLY
AND
CARE ADVICE
4 / 12

Note :
Every cam lock bolt must have a cam
lock connector in order to fasten the
parts together.
CAM LOCK FASTENER
ASSEMBLY
INSTRUCTIONS
cam bolt cam lockscrewdriver
4
Turn the cam lock clockwise gently
until it will not turn any more.
2
Insert the cam bolt into the
bolt hole of joint panel.
3
Align the cam lock with its side opening
(or arrow) pointing to cam bolt.
1
Screw the cam
bolt into panel.
5 / 12

END TABLE
FGI-2090C25
FGI-2090C35
6 / 12
0.47"
123
4
A
A
BC
C
C
D E
E
F
F
G
G
H
H
I
I
J
A1 A2 A3 A4 A5
1PC 2PCS 2PCS 2PCS 1PC
1PC 1PC 1PC 1PC 1PC
10PCS 10PCS 16PCS
12PCS
1PC 4PCS 2PCS 1PC 4PCS
D
D
BB

GET READY
Please group boards as below.
7 / 12
Body
GH I
C D
E
AB
Drawer
1PC 1PC 1PC
2PCS2PCS
1PC
2PCS 1PC
F1PC J1PC

8 / 12
1
H
D
E
F
J
Hardware ×10PCS
1
Hardware ×16PCS
3
Accessory ×1PC
A1
A1
11
1
1
1
1
1
1
3
3
3
3
3
3
3
3
3
3
3
3
3
Apply a dab of glue
into dowel holes of
panels before
inserting dowels (#3).
OPTIONAL
G
C
I
×2
×2

9 / 12

10 / 12
OPTIONAL
Dowelhole
4
5
Part ×2PCS
Hardware
B
×4PCS
4
4
4
4
4
Accessory ×1PC
A4
Top
Front
Part ×1PC
E
Hardware ×4PCS
2
2
22
2
Part ×1PC
F
Part ×1PC
JE
E
F
F
J
A4
or
Recommend using a
power tool to only tighten
hardware (#4) faster.
Accessory (#A4) could also
work for hardware (#4) if a
power tool is not present.
RECOMMEND
Top
Front
Please refer to Page 5 for
detailed instructions on
how to fasten cam locks
(#2) to cam bolts (#1).
2
1
B
B