Furniture of America CM7016CK-EK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7016CK-EK
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-30
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Wrench
(Not Included)

Page 2 of 7

#4 x 1 pc
Footboard
Parts List
#1 x 1 pc
Headboard
#3 x 2 pcs
Side Rail
#7 x 39 pcs
Slat
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 7
#6 x 4 pcs
HB/FB Leg
#2R x 1 pc
Right H/B Side
#5 x 2 pcs
Support Rail
#8 x 4 pcs
Support Rail Leg
Note: Right and left are determined
by facing the front of the bed in the
upright position.
#2L x 1 pc
Left H/B Side

#D x 36 pcs
Lock Washer
Hardware List
#A x 8 pcs
Bolt 5/16”x2”
#C x 4 pcs
Bolt 5/16”x2-1/2”
#G x 26 pcs
End Cap
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling the
product to avoid any potential injury and/or damage.
Page 4 of 7
#I x 1 pc
Wrench
#F x 26 pcs
Center Connector
#J x 8 pcs
Hex Nut
#B x 24 pcs
Bolt 5/16”x1-1/2”
#E x 36 pcs
Flat Washer
#H x 1 pc
Allen Wrench

Page 5 of 7
I. Align the right H/B side (#2R) with
the pre-drilled holes on the right
side of the headboard (#1).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#A) and then
the flat washer (#E) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through
the pre-drilled holes of the
headboard (#1) using the Allen
wrench (#H) to lock them with the
right H/B side (#2R).
IV. Repeat the process above to
assemble the left H/B side (#2L)
onto the headboard (#1). Turn right (clockwise) to tighten
#2R
#2L
#A x 8 pcs
#D x 8 pcs
#E x 8 pcs
I. Align the two HB/FB legs (#6)
with the pre-drilled holes
underneath the headboard
(#1).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock
washer (#D) onto the bolt
(#C) and then the flat washer
(#E) onto the SAME bolt
(#C), in that order.
III. Insert the bolt assemblies
through the holes of the two
HB/FB legs (#6) and secure
those bolts using the Allen
wrench (#H) to lock them with
the headboard (#1).
IV. Repeat the process above to
assemble the remaining two
HB/FB legs (#6) onto the
footboard (#4).
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
#6
Turn right (clockwise) to tighten