Furniture of America Karla CM7500GYQ User manual

Page 1 of 10
Assembly Instructions
EASY DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Rev: 18-01-04
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
For more information contact our team: [email protected]
CM7500Q
Allen Wrench
(Included)
(Not Included)
Phillips Screwdriver

BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
Page 2 of 10

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Parts List
#2 x 2pcs
Headboard Leg(L&R)
#1 x 1pc
Headboard
Hardware List
#B x 6pcs
Lock Washer Ø5/16"
#C x 6pcs
Flat Washer Ø5/16"
#D x 1pc
Allen key M4
#A x 6pcs
Bolt Ø5/16" x 1-3/8"
#E x 8pcs
Bolt Ø1/4" x 1-3/8"
#F x8pcs
Look washer Ø1/4"
#G x 8pcs
Flat washer Ø1/4"
#H x 17pcs
#3 x 1pc
Footboard
#6 x 2pcs
Drawer Slide Rail
#5 x 1pc Ø5/16"
#4 x 1pc
Footboard Drawer Support Slat
#7 x 2pcs
Footboard Drawer
#8 x 2pcs
Side Rails
Page 3 of 10
Screw #4 x 30mm
Footboard Drawer Support Leg
65x30x30mm

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#9 x 1pc
Rail Drawer Support Slat
#11 x 2pcs
Rail Drawer
#13 x 4pcs Ø5/16"
#12 x 1pc
Center Support
#14 x 1set
Slat (13 pcs)
#10 x 1pc Ø5/16"
#I x 24pcs
Screw #4 x 12mm
Page 4 of 10
Rail Drawer Support Leg
60x30x30mm
Slat support leg 310x30x30mm
#1
#2L
#2R
#3
#5
#4
#8
#6
#7
#7
#8
#9
#10
#11
#12
#13
#14

#D
#A
#B
#C
#A x 6pcs
#B x 6pcs
#C x 6pcs
#1
Page 5 of 10
#2L
#2R
#8
#8
#3
#1
Prepare 6 bolts assembly by inserting lock
washer (#B), then flat washer (#C) onto bolts
(#A). Align HB legs (#2R/L) to the holes of
the headboard (#1). Secure by using bolts (#A).
Align and hook the side rails (#8) to the latch of the headboard (#1) and footboard
(#3). Make sure it is firmly in place.

#D
#F
#E
#G
#5
#4
#E x 2pcs
#F x 2pcs
#G x 2pcs
#4
Page 6 of 10
#8
#8
Attach support legs (#5) to the holes of the support slat (#4).
Adjust the leveler on the support legs (#5) according to
ground level.
Prepare 2 bolts assembly by inserting lock washer (#F), then
flat washer (#G) onto bolts (#E). Align support slat (#4) to the
side rails (#8), then secure by using bolts (#E).

#E x 6pcs
#F x 6pcs
#G x 6pcs
#D
#F
#E
#G
#6
Page 7 of 10
#4
#10
#9
Prepare 6 bolts assembly by inserting lock washer (#F), then flat
washer (#G) onto bolts (#E). Align drawer rails (#6) to the holes
of the footboard (#3) and support slat (#4). Secure by using bolts
(#E).
Attach support leg (#10) to the hole of the drawer support slat (#9).
Adjust leveler of the support leg (#10) according to ground level.

#12
#13
Page 8 of 10
#H x 2pcs
#H
#9
#8
#8
Align drawer support slat (#9) to the side rails (#8), then secure by using screws (#H).
Align and attach support legs (#13) to the holes of the center support
(#12). Adjust the levelers of the support legs (#13) according to ground
level.

#H x 15pcs
#H
#I x 6pcs
#7,#11
#7,#11
#7,#11
X 4
Page 9 of 10
#8
#8
#14
#I
#I
#7 #11
#I
Align slats (#14) to the side rails (#8), then secure by using screws (#H).
Unfold the drawers (#7,11), then secure the drawers (#7,11)
by using screws (#I).

#7
ASSEMBLY IS COMPLETED
Page 10 of 10
#7
#11
#11
Align and attach the drawers (#7,11) through
the center metal glides.