Furniture To Go 1040601 User manual

Black 1040620
Soft grey 1040652
Assembly Instructions - Please keep for future reference
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts please contact your retailer
White 1040601
Issue 1 - 31-10-2016
3+3 Drawer Chest
Dimensions
Width
Depth
Height
:
:
:
350830
148.1 cm
40.0 cm
72.4 cm

!Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
pages 2 and 3.
•Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
•Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
•We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
•Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page
with these instructions for
future reference.

Components - Panels
Please check you have all the panels listed below
2
350830-03
2
(63,9 cm x 35 cm)
Side, left
11
(61,5 cm x 15,8 cm)
Drawer back
12
(62,5 cm x 34,7 cm)
Drawer bottom
10
(35 cm x 15,8 cm)
Drawer side, right/left
4
x
1
(148,1 cm x 40 cm)
Top
3
(63,9 cm x 35 cm)
Side, right
4
(70,9 cm x 4,4 cm)
Post
6
(136,3 cm x 6 cm)
Front rail
9
(67,7 cm x 18,9 cm)
Drawer front
7
(67,4 cm x 7 cm)
Back rail
8
(60,0 cm x 71,0 cm)
Back
6
x
6
x
6
x
12
x
2
x
5
(70,9 cm x 36,5 cm)
Divider
2
x
13
Safety label
2
x

Components - Fittings
Please check you have all the panels listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
3350830-04
10 ø7.8 x 40mm Wooden dowel x
Aa Ab
ø6 x 30mm Wooden dowel x 12
Cb
ø5 x 8, cc34mm Bolt x 33
Ca
ø15 x 10.5mm Cam x
35
1.2 x 15mm Nail x
Di
50
Kb
ø5.8 x 8mm Screw x
18
17060 16040 90 15013070 120100 14011050 803020100
Ruler - Use this ruler to help correctly identify the screws
Tools required
Flatblade screwdriver
(Medium)
Hammer Phillips screwdriver
(Medium & large)
Back fitting w. ø3.5 x 15mm Screw x
Fi
12
ø4 x 25mm Screw x
Jb
16
ø3 x 35mm Screw x
Bp
24
Ge
12 ø27 x 24mm Metal Knob x M4 x 20mm Screw x
Hd
12
2
Vl
44 x 23 x 23mm Angle x
Ko
8
ø4,2 x 9,5mm Screw x
Cd
M4, cc34mm Bolt x 2
Cm
M4 / ø5 x 12mm Threaded tube x
1
Kf
18
ø5.8 x 19mm Screw x
ø18 x 9mm Spacer x
Nu
18
Back fitting - 14 x 19mm x
Fc
3
Wall strap and instruction x 2
Fh
6
CL
350mm Drawer runner, left, side x
6
DL
350mm Drawer runner, left x 6
DR
350mm Drawer runner, right x
6
CR
350mm Drawer runner, right, side x
ø3 x 12mm Screw x
Bo
27

Assembly Instructions
Fix the posts
4
onto the
sides
2
and
3
using
screws
Jb
into the holes
indicated.
The top of the posts
4
and
the sides
2
and
3
must
be ush.
Step 1.1
Assembly of the chest.
Step 1
Knock the dowels
Aa
into the holes indicated
on the sides
2
and
3
using a small hammer.
Screw the bolts
Cb
into
the holes indicated on the
sides
2
and
3
.
Step 1.2
4
350830-05
Cb
ø5 x 8, cc34mm Bolt x 2
ø4 x 25mm Screw x
Jb
16
4
ø7.8 x 40mm Wooden dowel x
Aa
Jb
Jb
Cb
Cb
Aa
Aa
Aa
Aa
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
3
4
4
4
4
2
6
4
4
2
4
1
3
4
7
3
2
8
44
32
4
Jb
Jb
Jb
Jb
Jb
5
8
7

Assembly Instructions
Place the spacers
Nu
as shown, and x the
upper drawer runners
CL
and
CR
to the sides
2and 3using screws
Kf
through the holes
indicated.
See details.
Step 1.3
Fix the drawer runner
CL
to the right hand side
of the divider 5using
screws
Kb
through the
holes indicated.
Turn around the divider
5 and x the drawer
runner
CR
using screws
Kb
through the holes
indicated.
See details.
Step 1.4
350830-06
5
3
Kf
Note the hole!
Bottom end of
right hand side
Kf
18
ø5.8 x 19mm Screw x
Kf
Kf
Kf
2
ø18 x 9mm Spacer x
Nu
18
Nu
Nu
Nu
Nu
Nu
6
CL
350mm Drawer runner, left, side x 6
CR
350mm Drawer runner, right, side x
3
CL
350mm Drawer runner, left, side x 3
CR
350mm Drawer runner, right, side x
5
Kb
Kb
Kb
Kb
Kf
Nu CL CR
Kf
Kf
CL
CL
CL
CR
CR
CR
Kb
CL
CR
Kb
CL CR
CR
CL
CL CR
Kb
Kb
Kb
Kb
Kb
Kb
Kb
Kb
Kb
Kb
Kb
Kb
Kf
Kf
Kf
Kf
Kf
Kf
Kf
Kf
Kf
Kf
Kf
Nu
Nu
Kb
ø5.8 x 8mm Screw x
18

Assembly Instructions
Knock the dowels
Aa
into
the holes indicated on the
divider
5
using a small
hammer.
Screw one of the bolts
Cd
into the threaded tube
Cm
.
Push the bolt
Cd
/ the
tube
Cm
into the hole indi-
cated on the divider
5
.
Screw the remaining bolt
Cd
into the threaded tube
Cm
from the opposite side
of the divider
5
.
Step 1.5
Fix the angles
Vl
using
screws
Ko
into the holes
indicated on the front
rail
6
.
Screw the bolt
Cb
into
the hole indicated on the
front rail
6
.
Step 1.6
Screw the bolts
Cb
into
the holes indicated on the
top
1
.
Step 1.7
6
350830-07
5
Aa
Aa
Cm
Cd
Cd
Cm
M4 / ø5 x 12mm Threaded tube x
1
2 ø7.8 x 40mm Wooden dowel x
Aa Cd
M4, cc34mm Bolt x 2
Vl
Ko
Ko
Cb
6
Vl
Ko
Cb
Cb
Cb
Cb
Cb
Cb
1
Cb
ø5 x 8, cc34mm Bolt x 6
Ko
4
ø4,2 x 9,5mm Screw x
2
Vl
44 x 23 x 23mm Angle x
Cb
ø5 x 8, cc34mm Bolt x 1

Assembly Instructions
Knock the dowels
Aa
into
the holes indicated on
the back rails
7
using a
small hammer.
Step 1.8
Place the back rails 7
onto the divider 5as
shown.
Push cams
Ca
into the
holes indicated on the
back rails 7.
Arrows pointing towards
the divider 5.
Turn the cams
Ca
to the
right to x the back
rails 7.
Step 1.9
Place the sides
2
and
3
onto the back rails
7
.
Push cams
Ca
into the
holes indicated on the back
rails
7
. Arrows pointing
towards the sides
2
/
3
.
Turn the cams
Ca
to the right to x
the sides
2
and
3
.
Step 1.10
350830-08
7
Ca
ø15 x 10.5mm Cam x
2
7
Ca
Ca
ø15 x 10.5mm Cam x
2
7
5
2
3
7
7
Ca
Ca
Ca
2
x
7
Aa
Aa
4
ø7.8 x 40mm Wooden dowel x
Aa

Assembly Instructions
Fix the angles
Vl
on the
front rail 6to the sides
using screws
Ko
.
See detail.
Step 1.12
Place the top
1
onto
the sides
2
/
3
and the
divider
5
.
Place the front rail
6
onto the divider
5
.
Push cams
Ca
into the
holes indicated on the
sides
2
and
3
and the
divider
5
.
Turn the cams
Ca
to the
right to x the top
1
and
the front rail
6
.
Step 1.11
8
350830-09
Ko
4
ø4,2 x 9,5mm Screw x
Ko
6
3
2
Ca
Ca
1
Ko
Ca
ø15 x 10.5mm Cam x
4
6
Ca
Ca
Ca
Ca
5

Assembly Instructions
Step 1.13
Place one of the backs
8into the rabbet on the
top 1,onto the divider
5and the post 4.
!
Important!
The back 8
must cover half
of the back edge of the
divider 5.
See
details.
Fix the
back
8
to
the top 1, the
post 4and the back
rail 7
using nails
Di
.
Use a small hammer.
Step 1.14
Place the back 8into
the rabbet on the top 1
and onto the divider 5.
Fix the back
8
to the top
1, the post 4and the
back rail 7
using
nails
Di
.
Use a
small
hammer.
350830-10
9
1.2 x 15mm Nail x
Di
18
7,5mm
7,5mm
8
8
1
7
5
5
7
1
Di
Di
Di
Di
1.2 x 15mm Nail x
Di
18

Assembly Instructions
Step 1.15
Finally x the backs
8
to
the divider 5 using
screws
Bo
and the back
ttings
Fc
.
See detail.
Step 1.16
!
Important!
The chest of
drawers is heavy.
Lift with care.
Its recommended that the
chest is xed to the wall.
Use the ttings
Fh
. Follow
the instructions on the
following pages.
350830-10
9
1.2 x 15mm Nail x
Di
18
7,5mm
7,5mm
8
8
1
7
5
5
7
1
Di
Di
Di
Di
1.2 x 15mm Nail x
Di
18
10
350830-11
Fc
Bo
Bo
Bo
Fc
Fc
Back fitting - 14 x 19mm x
Fc
3
Wall strap and instruction x 2
Fh
ø3 x 12mm Screw x
Bo
3
8
8

Assembly Instructions
Place the chest of
drawers up against the
wall.
Draw lines as
shown using a
pencil.
Step 1.17
Fix the straps to the wall
40mm below the lines as
shown.
Note!
See next page for
information on how
to x the straps
to the wall. The
screws and plugs
needed is NOT included.
Step 1.18
Push the straps through
the holes indicated on
the back of the top 1
and push the chest
of drawers up
against the wall.
Step 1.19
Fix the straps to the top
1using the screws and
washers provided.
See detail.
Step 1.20
350830-12
11
40 mm
1
1
1

A Guide to
Wall Mounting & Fixings
350830-12
11
40 mm
1
1
1
No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board.The hammer fixing allows it to
be fixed to the wall rather than the plaster
board.Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.

Assembly Instructions
Fix the drawer sides 10
to the drawer back 11 as
shown, using screws
Bp
.
Step 2.1
Assembly of the drawers.
Step 2
Knock the dowels
Ab
into the holes indicated
on the drawer sides 10
using a smal hammer.
Step 2.2
Slide the drawer bottom
12 into the drawer
sides 10 .
Step 2.3
350830-14
13
Ab
Ab
Ab
ø6 x 30mm Wooden dowel x 12
6
x
6
x
6
x
10
10
11
Bp
Bp
6
x
12 9
10
10
11
ø3 x 35mm Screw x
Bp
24
12
10
10
10
10

Assembly Instructions
Step 2.4
Screw the bolts
Cb
into
the holes indicated on
the drawer front 9.
Step 2.5
Push the drawer front
9
onto the drawer sides
10
.
Place cams
Ca
into the
holes indicated. Arrow
pointing towards the front.
Turn the cams
Ca
to the
right to x the front.
Step 2.6
!
Important!
Make sure the
angle between
the drawer front
9
and
the drawer sides
10
is 90°
before the drawer bottom
12
is xed using
Fi
as
shown.
To adjust the angle between
the drawer sides and the
fronts push the tting
Fi
sidewards. See details.
Fix the drawer runners
DL
and
DR
to the drawer sides
10 using screws
Bo
into
the holes indicated.
350830-14
13
Ab
Ab
Ab
ø6 x 30mm Wooden dowel x 12
6
x
6
x
6
x
10
10
11
Bp
Bp
6
x
12 9
10
10
11
ø3 x 35mm Screw x
Bp
24
12
10
10
10
10
90°
14
350830-15
Cb
ø5 x 8, cc34mm Bolt x 24
9
Cb
Cb
6
x
6
x
10
10
Ca
Ca
9
Ca
ø15 x 10.5mm Cam x
24
12
10
10
Fi
11
9
Fi
Fi
6
x
Fi Fi
Back fitting w. ø3.5 x 15mm Screw x
Fi
12
6
DL
350mm Drawer runner, left x
ø3 x 12mm Screw x
Bo
24
6
DR
350mm Drawer runner, right x
Bo
DL
Bo
DR
Bo
Bo
DL

Assembly Instructions
Step 2.8
Remove the paper on
the back of the Warning
labels 13 and place them
inside the upper drawers
as shown.
Step 2.7
Fix the metal knobs
Ge
to
the drawer front 9using
screws
Hd
.
350830-16
15
Permanent safety label. Please do not remove.
WARNING!
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
• Use the wall attachment device provided
• Never allow children to climb or hang on
drawers, doors or shelves
• Place heaviest items in the lower drawers
or shelves
• Unless specifically designed to
accommodate, do not set TV's or other
heavy objects on top of this product
• Never open more than one drawer at a
time
An attachment device is provided with your product,
however you will need to source suitable fixings for your
wall type. If in doubt, please consult a qualified
tradesperson
Always ensure the wall to be drilled is free from hidden
electrical wires, water and gas pipes.
M4 x 20mm Screw x
Hd
12
Ge
12 ø27 x 24mm Metal Knob x
6
x
Ge
Hd
9
Hd
Ge
13