Furo Systems Furo X User manual

Furo X
Owner’s Manual

Warning. Before every ride!
Cycling is an inherently dangerous activity.The likelihood of accidents is
greatly increased if your Quick Release Skewer (or any part) is incorrectly
installed.
Incorrect installation or damage to the Quick Release Skewer or any other
part could cause an accident resulting in injury or death.
Before you ride.Make sure all the components are tightly fastened and
secure to the bike.
Check the brakes by making
sure the levers cannot be pulled
all the way
Ensure that the seat tube is
not over extended
Make sure the
stem is securely
locked up
Check that the central folding
mechanism is locked out and that
the lever cannot be turned
123
Make sure the Quick Release Levers are Closed.
If the quick release lever can be easily closed, this means it
is not secured tightly enough! Open the lever and tighten
the tension adjusting nut until it can be closed tightly.
Adjusting
Nut
6
Ensure the battery is SECURELY
LOCKED
Riding with an unlocked battery
will lead to an unsecure connection
and will damage the battery
45
7
Helmets save lives!
Always wear aproperly fitted
helmet when you ride your Furo X

1
Your Package Contains
The Basics
1 2
Push the power
button to start The
battery
Press and hold the
mode button to
start the bike
3
Select power assist
level
Six Tool SET
#2 Phillips screw driver
2/3/4/5/6 mm Allen Key
Bike Wrench
15 mm / 17 mm
Charger
36V Battery Pack
with USB Charging
port and integrated
indicators
2x Battery keys 2x Pedals
Front Headlight 2x Wheel Reflectors

2
Getting Your Bike Ready For Your First Ride
Remove all the
packaging from
your new FX
Locate and unfold
the steering stem
Straighten up and
lock the handlebar
Slide the battery
above the rear
wheel and lock it
Screw in the right
pedal on the right
side clockwise, and
the left counter-
clockwise
Raise and adjust the
seat post
Adjust the
height of the
steering stem
12
9
56
4
87
Identify the right
and left pedal
marked on the top
3
Unfold your FX and
lockout the frame
with the central lever

3
Familiarize Yourself With Your FX
Get a Grip On The FX Dashboard
Front Headlight
Rear Brake
Front Brake
Battery Life
Indicator Power Assist Level
On-Board Computer
Mode And Power Level
Select Button
Thumb Shifter
Gear Indicator
Indicators

4
Technical Table
Motor BAFANG Rear Hub Motor
Nominal/Peak Power 250W/500W
Pedal Assist Top Speed 25km/h (can be modified via computer to
comply with local regulations)
Range More than 45km at average pace
Charge Time 4.5hrs (2hrs with optional fast charger)
Display Backlit LCD with controls
Computer CURTIS KD21C with modifiable speed limit
and 6km walk assist
Standard Battery Type Lithium-Ion Samsung Cells
Standard Battery Specs 36v 8.7Ah 313Wh
MAX Battery Type Lithium-Ion LG Cells
MAX Battery Specs 36v 10.5Ah 378Wh
Readouts Distance traveled, current velocity (km/h or
mph), battery autonomy and mode
Pedal Assist 5 Levels
Frame Full carbon foldable in 3 steps
Fork Custom full carbon
Rear deraiilleur Shimano Sora 9 speeds
Brakes Shimano M315 Hydraulic Disk Brakes
Tires CST C1576 Black 20*1.75

5
Folding Your FX
12
34
5 6 7
Identify the seat post and
stem quick release levers.
Shorten the seat post and
steering stem. (Optional)
Press down the
red security lock Pull the
release lever
Fold the
stem Press the unlock
button and release
the central lock
Fold the FX

6
Charging Procedure
Open the
rubber charging
port cover
Insert the
charging lead
Plug the charger lead
into the mains
123
45
Charger light will turn
red to indicate charging
Charger light will turn green
when charging is complete
Approx.
4 Hours
The On-Board Computer Systems
What does your screen tell you?
3 Buttons
Up
Mode
Down

7
Using The Pre-Installed Indicator Lights
12
3
457
Switch on the indicators by
pressing the white button behind
the battery
You can activate the indicators
using the remote on your
dashboard
The indicator buttons will flash red when the indicators are activated.
You can hold both left and right buttons to activate the hazard lights
To recharge your
indicators you need to
first slide the indicators
out of the battery
Charge the indicators
using any USB
charging port with the
cable provided
If the indicator remote is
not working. You need to
replace the internal
CR1620 battery by
opening up the remote.

8
Power On/Off
Hold down the MODE button and the display will switch on and light
up (if the battery has been switched on…). Hold down the MODE
button again and the display will switch off.
Walk assist mode
Press and hold the DOWN button for 2
seconds and your e-bike motor will start
to run at auniform speed of 6Km/h.The
display will show “P” on the screen whilst
in this “Walk Assist” mode.
Using The On-Board Computer
Led Backlight
Press UP for 2seconds to turn on the backlight of the display.Hold
UP again for 2seconds and the light is turned off.
Power assistance selection
Use the UP and DOWN buttons to
change the assistance provided by the
Motor.The power ranges from level 1to
level 5
Access the settings
1- Hold both UP and DOWN for 2 second to enter the Settings Menu.
2- Then navigate through the settings by tapping the MODE button.
3- Use UP and DOWN to chooses settings and MODE to confirm
Trip distance
clearance
Select ‘y’ to clear
trip distance
Backlight
contrast
Choose level 1/2/3
screen backlight
brightness
Imperial and
Metric units
“1” is Imperial
“2” is Metric

9
Give Your FX Love And Attention
Pre-Ride Checks
Maintain Pressure
2.4-3.1 bar / 35-45 psi
Lubricate chain
every 3 months
Ensure battery
is not drained when not in
use
Check the brakes by making
sure the levers cannot be
pulled all the way
Ensure that seat tube is not
over extended
Make sure the stem is
securely locked up
Check that the central folding
mechanism is locked out and
that the lever cannot be turned
12
34

10
Safety Instructions
CAUTION!
Only use the provided battery charger.
Only charge the FX indoors, in a well ventilated and dry location
(i.e. keep out of the rain and avoid extreme temperature
fluctuations).
For ultimate charging, charge at temperatures between 0°C and
50°C.
Place charger on ahard surface and ensure it is not covered.
Never place on carpet or another textile surface.
Always keep the plug and charger connector free of dirt and
moisture, especially while charging.
Do not use the charger or charger plug when damaged.If in
doubt about the condition of your charger, please contact
FuroSystems.
Never charge the battery in direct sunlight.Keep away from
windows or open doors.
When the FX isn't used for along period, please make sure the
battery is either connected to the charger or the battery gets a
full charge cycle every 6months
Ensuring Battery Health
•Please charge at least every 6 months
•Never store the FX for more than one month with a drained
battery
The strength & stiffness of carbon fibre composite frames &
components can be adversely affected by high temperatures. Do
not keep the bike in poorly ventilated areas, where it is exposed to
radiant heat sources.

11
Warranty
Disclaimer
WARNING!
FuroSystems guarantees each new bicycle frame against defects in
workmanship and materials for two years. All original components
are also covered by warranty for aperiod of two years from the
date of purchase.This warranty is expressly limited to the
replacement of adefective frame, or defective parts and is the sole
remedy of the warranty.This warranty applies only to original
owners and is not transferable.Claims under this warranty must be
made directly to the place at which you purchased the bike, and
proof of purchase is required.This warranty does not cover normal
wear and tear, improper assembly or follow-up maintenance, or
installation of parts or accessories.The warranty does not apply to
damage or failure due to accident, misuse, abuse, or neglect.
Modification of the frame or components shall void this warranty.
Under no circumstances, including, but not limited to negligence,
shall FuroSystems or FuroSystems distributor (seller) be liable for
any special or consequential damages that result from the inability
to use the materials in this manual, even if FuroSystems has been
advised of the possibility of such damages. Applicable law may not
allow the limitation or exclusion of liability or incidental or
consequential damages, so the above limitation or exclusion may
not apply to you.
As with all mechanical components, bicycles are subjected to wear
and tear, as well as high stresses.Different materials and
components may fatigue in different ways. If the design life of a
component has been exceeded, it can suddenly fail, possibly
causing injuries to the rider.Any form of crack, scratches or change
of colouring can indicate that the life of the components has been
reached and should be replaced.
WARNING!
Cycling is an inherently dangerous activity. The likelihood of
accidents is greatly increased if your Quick Release Skewer (or any
part) is incorrectly installed. Incorrect installation or damage to the
Quick Release Skewer could cause an accident resulting in injury or
death.

12
WARNING!
Your bicycle must comply with your countries legal requirements
when riding on public roads and in all conditions, including bad
weather, night time, dusk or dawn.Many countries require specific
safety devices. It is your responsibility to familiarize yourself with
the laws of the country where you ride and to comply with all
applicable laws including properly equipping yourself and your bike
as the law requires
WARNING!
Inspection and maintenance are important to the safety and
longevity of your bicycle.Regularly check brakes, tyres, steering
and rims.Any part of apoorly maintained bike can break or
malfunction leading to an accident resulting in serious injury or
death.
WARNING!
Riding in the city is hazardous. Failure to wear ahelmet when riding
may result in serious injury or death.
WARNING!
Please note all the product specific demands for third party
products you add to the bike. Child and baggage carriers add
weight and raise the centre of gravity making balance and
cornering more difficult. If you lose control, you and your child
passenger can be severely injured or killed.
WARNING!
Failure to confirm compatibility, properly install, operate and
maintain any component or accessory can result in serious injury or
death.Do not modify your bike frame or components in any way.
Modifications can cause damage leading to an accident that can
result in severe injury or death. Incompatible accessories or
improper mounting of accessories can adversely affect the
performance of your bicycle and may be unsafe

13
Copyright Notice
Trademarks
©Copyright FuroSystems LTD.All rights reserved.
This material provided by FuroSystems LT D is the property of
FuroSystems LTD and is protected by copyright, trademark and
other intellectual property laws.You may view this material and
print this material only for personal use, provided that you
maintain all copyright, trademark and other proprietary rights or
notices.You may not otherwise use, reproduce, store, post,
broadcast, transmit, modify, sell or make available to others or the
public, content from this material without the prior written
approval of FuroSystems LTD.
FuroSystems®is aregistered trademarks of FuroSystems LTD.
Standards and Conformity
The FX is an electric power assisted cycle developed in accordance
with:
•2006/42/EC The Machinery Directive
•2004/108/EC The Electromagnetic Compatibility Directive
and is in conformity with the applicable requirements of the following
documents:
•EN 15194:2009+A1Cycles -Electrically power assisted cycles -EPAC
Bicycles
Contact Information
The FX is aproduct of FuroSystems LTD aUK registered company,
Registered number:10411786
www.furosystems.com
[e-mail]
EN