FUTABA T16IZ Ver.2 Manual

1M23Z07703
GYA553
T16IZVer.2
Settingmanual

3
T16IZ
S.I/F
CGY 接続コード（ジャイロに付属）
GYA553
Byinstallingthelatestsoftware(Ver.2~)ontheT16IZ,youcansetting
theairplanegyroGYA553ontheT16IZ.
ConnectionT16IZandGYA553
ConnectionT16IZandGYA553
ReciverConnectionCable
(includedwithgyro)
CAUTION
Be sure to connect and disconnect the GYA553 and
T16IZ connection cable with the power off.

4
1.Select“Gyrosetting”onthelastpageof
AirplaneModelMenu
3.Homescreenisdisplayed
ToBasicmenu
2.Select"Start"
Select"Start"
Thiswilldownloadthegyrodata
totheT16IZ.
*Atthistime,ifGyroisnotconnectedto
T16IZbywire,thisscreenappears.
Tap"Yes"todisplaytheGYA533datasaved
inT16IZ.
1
3
2
SETTING
When"GYSettingsTransfer"is
selected,thegyrosettingdatasaved
inT16IZiswrittentothegyro.
◆ WhencopyingdatafromGyroAtoGyroB
ConnectthegyroAtotheT16IZandpress[Start].(EnterthedataofAintoT16IZ)
ConnectGyroBtoT16IZandpress[GYSettingsTransfer].(PutdataonAintogyroB)
IfyoupressStarthere,theBdatawillbedownload
totheT16IZandtheAdatawillbelost.

5
On the home screen, basic information such as gyro operation
mode, sensitivity, battery voltage are displayed.
Homescreen
Homescreen
Battery voltage
Displays the voltage of the
receiver battery connected to
GYA.
Gyro operation mode / Gyro gain
Displays "AVCS" or "Normal" opera-
tion mode and gyro gain of aileron
(roll), elevator (pitch) and rudder
(yaw) axis.
Homescreen
Basicmenu
Basicmenu
Basicmenu
◆ Config
◆S.BUSbasic

6
Config 1/6 WING/TAIL
Set with the wing type/tail type of GYA553. The wing type/tail type of the transmitter is not used
and is normal.
Ɣ7XUQR൵WKHHOHYRQ9WDLOPL[LQJRQWKHWUDQVPLWWHUVLGH
Ɣ'RQRWXVHWUDQVPLWWHUVXEWULP$GMXVWXVLQJWKHJ\URQHXWUDOR൵VHW
Ɣ:KHQXVLQJWKH6%86VHUYR\RXFDQDOVRXVHWKHQHXWUDOR൵VHWIXQFWLRQRI
WKH6%86VHUYRVHWWLQJSDUDPHWHUV
Config
Config
Set the mounting direction of GYA. Set mounting
GLUHFWLRQZLWKUHIHUHQFHWR¿JXUHEHORZ
Config 1/6 Gyrosetmountingdirection
Selectwingtype
Selecttailtype

7
Config
Config
Config 1/6 Servotype
Digitalservo Analogservo
Select the servo type according to the servo to be
used.
Digitalservo → DG:285Hz
Analogservo → AN:70Hz
7KHVWDELOLW\RIGLJLWDOVHUYRPRGHRIDIOLJKW
LQFUHDVHVLQRUGHUWRSHUIRUPDKLJKVSHHGFRQWURO
action.
6HOHFWWKH6%5SRUW
Config 1/6 SB/R2OUT
Whenusingtworudderservos
S.BUSdevicescan
beconnectedtothis
port.
Headdirectionmark
MODESW DATASW
MODELED
Aileron1
Programbox S.BUS2
Aileron2
Elevator Elevator2
Rudder
S.BUS/Rudder2
DATALED
S.BUS Rudder2

8
Config
Config
Config 2/6Gyrodirection
,WLVWKHGLUHFWLRQVHWWLQJRIWKHJ\UR%HFDUHIXODVLWZLOOFUDVKLIWKHGLUHFWLRQLVUHYHUVHG
For dual aileron, dual elevator, and dual rudder aircraft, check the operating direction of each second aile
ron/elevator/rudder.
Turntheairplanetotherighton
thegroundandcheckthatthe
rudderoperatestotheleft.
Tilttheairplanetothelefton
thegroundandcheckthatthe
aileronsoperatetotheright.
Raisetheairplanewithitsnose
upwardandcheckthatthe
elevatoroperatesdownward.
Neutral position setting for each servo.
Config 3/6 Neutraloffset
Thiswillmovetheneutraltothedesiredposition.

9
Config
Config
This is the limit setting for each servo. The position
RIWKHPD[LPXPRSHUDWLRQLVUHDGLQWRWKHJ\URLQ
WKH¿UVWVHWWLQJ
Config 4/65/6 Servolimit
Adjustthevalue(%)toreachthe
maximumoperatingposition
Adjustthevalue(%)toreachthe
maximumoperatingposition
Maximumangle
Maximumangle
Sticktofullright
Sticktofullleft
Aileronexample
5HVHWHDFK&RQ¿JLWHP,WUHWXUQVWRWKHLQLWLDOYDOXH
Config 6/6 Reset

10
!10CHON
Thechannelofeachfunction
canbechanged.
ReseteachS.BUSfunction.Itreturnsto
theinitialvalue.
SBUSBasicmenu
SBUSBasicmenu
ON-OFFchannelforautorecovery.
6HWWKH&+IRUHDFKIXQFWLRQDFFRUGLQJWRWKHWUDQVPLWWHUWREH
XVHG$Q\XQXVHGIXQFWLRQVVKRXOGEHVHWWR,1+,QKLELWHG
WARNING
Always verify that the S.BUS function assignments
match your transmitter’s function (in the FUNCTION
menu) assignments. If any changes are made within
the transmitter function assignments, then it will also
be necessary to make the changes within the S.BUS
function assignments. To change the channel, GYA553
and T16IZ must be connected.