FUTABA R334SBS Technical manual

1M23Z05806
R334SBS/R334SBS-E Software update manual
Requiredforupdate(Purchaseseparately)
Preparations
-1-
&,8RU&,8
RSWLRQDO
3&
'RZQORDGLVSRVVLEOHE\WKHZHE
&*<*<*<([WHQVLRQVؙRSWLRQDO
'6&FDEOHؙRSWLRQDOIRU39
RU
0LQL'ULYHUؙ7RSXVKWKHVZLWFKRI
WKHUHFHLYHU
86%3RUW
1.
InstallthedriverfortheCIU-3/CIU-2ontoyourPC.
WhentheCIU-3isfirstconnectedtothePC,downloadtherecommendeddriversoftware.The"Found
NewHardwareWizard"windowappearsonthescreen.Click"Locateandinstalldriversoftware".
WhentheCIU-2isfirstconnectedtothePC,the"FoundNewHardwareWizard"windowappearsonthe
screen.InstallthedriversdownloadfromlocalFutabadistributor'sWebsite.
RefertothemanualoftheCIU-3/CIU-2forfurtherinformation.
CIU-3orCIU-2
*The screen can vary based on the PC.
<RXU)XWDED56%656%6(SURJUDPFDQEHXSGDWHGHDVLO\RQOLQH:KHQIXQFWLRQVDUHLPSURYHGWKHXSGDWH¿OH
can be downloaded from Futaba distributor's website.

1.
Downloadthezipfileoftheupdatedatafromyourlocal
distributor'swebsite.

Updatingprocedure
2.
Extractthezipfileonyourcomputer.
FutabaWEBsite
Software
Download
-2-
&*<*<*<
([WHQVLRQVؙRSWLRQDO
RU'6&FDEOHؙRSWLRQDOIRU39
&,8RU&,8
RSWLRQDO
56%656%6(
5HFHLYHUEDWWHU\
/LQNVZLWFK岜/('
6%86
7R6%86
([WUDFW$OOWRWKHH[HFXW
DEOHrOH
&+
3&
'RZQORDGLV
SRVVLEOHE\
WKHZHE
86%3RUW
3.
Connectasshowninthediagram.
Updateprogram
Executablefile
*Put in the same folder.

4.
 Turnonthereceiverpowerwhilepressingdownthe
Linkswitch.
5.
OncetheLEDconfirmsbyflashingredonce,releasetheLinkswitchandpressagain.
6.
WhenyoucontinuepushingtheLinkswitch,theLEDstartsflashingredandgreen.
(OnceflashingRedandGreen,theinitialprocessiscomplete.)
-3-
&+
1.HolddowntheLinkswitchfirst.
2.NextturnONthe
receiver.
RedandGreenlight.
Updateready
7.
StartthePCupdate.(Thereceivershouldkeepredandgreenon.)
Write
2.
R334SBS

-4-
Don'tturnoffthepower!
Waitforabout2minutes.
Greensteadylight
R334SBS/R334SBS-E
Completed
8.
 TurnoffthepowerswitchofyourreceiverandremovetheCIU-3/CIU-2.
9.
Besuretocheckeachfunctionbeforeuse.
Error
1.
Ifanerrordisplayappears,replaceanwiththeupdatefromthebeginning.
◆Thereceiverisnotintheupdate"ready".
◆Thecableisdisconnected.
◆Thepowerhasbeenturnedoff.

R334SBS/R334SBS-E SOFTWARE UPDATE CHANGES
Version: 3.0
R334SBS/R334SBS-E SOFTWARE UPDATE CHANGES
Version: 2.0
1.CompatiblewithWirelessS.BUSsettingfunction
1.CompatiblewithWirelessMC970CRparameterssettingfunction
TheoperatingparametersoftheFutabaprogrammableS.BUS2servoconnectedtoreceivercanbesetand
changedfromthetransmitterwirelessly.
TheoperatingparametersoftheFutabaMC970CRconnectedtoreceivercanbesetandchangedfromthe
transmitterwirelessly.
*Transmitter (T7PX) also needs to be updated to version 2.0.
*Please refer to the update manual of the T7PX transmitter (Ver.2.0) for how to use the wireless S.BUS
setting.
*Transmitter (T7PX/T7XC) also needs to be updated to version 3.0.
-5-
FUTABA CORPORATION
oak kandakajicho 8F 3-4 Kandakajicho, Chiyoda-ku, Tokyo 101-0045, Japan
TEL: [phone], FAX: [phone]
©FUTABA CORPORATION 2018, 9 (1)
ųƄƕƄƐƈƗƈƕŃŶƈƗƗƌƑƊ
ųƄƕƄƐƈƗƈƕŃŶƈƗƗƌƑƊ
ŶőťŸŶŕ ŶťŰŐŔ ŰŦŜŚœŦŵ
SBM-1
LINK Rx
S.BUS MotorController Module