Future SLICK540 User manual

Electric Remote-controlled Model Aircraft
SLICK540-60"70e
敬告：安装前请仔细阅读说明书。本产品非玩具，必须在有经验人士
指导下进行安装和飞行。
,QVWDOODWLRQ0DQXDO
:DUQLQJ3OHDVHUHDGWKHLQVWUXFWLRQVFDUHIXOO\EHIRUHLQVWDOODWLRQ7KLVSURGXFWLVQRWDWR\,W
PXVWEHLQVWDOOHGDQGIORZQXQGHUWKHJXLGDQFHRIH[SHULHQFHGSHUVRQQHO

2
打开包装时,请检查部件是否齐全,如有缺漏,请及时与经销商联系。
When unpacking, please check whether the parts are complete. If there is any missing, please
contact the dealer in time.
Specification：
Wingspan：1524mm
Length：1477mm
Wing Area：48dm2
Weight：2900g（including battery）
Center of gravity position: 135mm back from top of leading edge of wing
Recommended rudder setting:
Elevator : high rates: 45 °, low rates: 25 °
Rudder : high rates: 45 °, low rates: 25 °
Suggested power configuration：
Motor：Brushless 5050/500kv/1350W；
ESC: 120A
Battery：6s 25c 3300MAH
Plane Blade： 15*8E
Servo：5KG Medium servo
Flight Precautions
Please do not fly in the following environments:
Note: Due to the continuous updating of the product, there may be small
errors between the manual and the actual product.
1.The battery must be removed during storage, otherwise it may explode and burn
2.After the flight, please do not squeeze the model when storing. It is better to hang it up
Precautions for storage:
1. Not in the wind. Poor visibility. Flying in bad weather such as rain.
2. Don't be in a crowd. High voltage line near the strong electromagnetic interference occasions flying.
3. Not in tall buildings. Forest street lights and other sundries to fly in the field.
4. If this is your first flight, please fly under the guidance of an experienced person
5. Remember, model aircraft are not toys and you are fully responsible for the safety of the flight.

2.Install the chip first before installation servo
3.Stick the chip of servo by glue
6.Install the undercarriage
4. Install the rudder and elevator servo
5.Put the connect line of servo into
the fuselage
3
1. Remove the battery before storing the model to prevent the risk of explosion or combustion.
2. Do not put objects on the model - hang it up if possible.
1. Remove the battery before storing the model to prevent the risk of explosion or combustion.
2. Do not put objects on the model - hang it up if possible.
1. Remove the battery before storing the model to prevent the risk of explosion or combustion.
2. Do not put objects on the model - hang it up if possible.
Note: Due to the continuous updating of the product, there may be small errors between the manual and the actual product.
1. The battery must be removed during storage, otherwise it may explode and burn
2. After the flight, please do not squeeze the model when storing. It is better to hang it up
1. Connect servo extension leads to the
elevator and rudder servo cables.

7.Install the head push rod
12.Secure the box with glue
8.Install the elevator angle
9.Install the elevator and flat tail, and fix
the hinge position with glue. Leave 1mm
between the flat tail and elevator,so that it
can be risen and down very flexible
10.Carefully insert the tail-plane into
the fuselage with glue
11.Install the set-up box in the rear fuselage
4

17.Install the chip first before installation servo
16.Install the tail-wheel bracket
15.I nstall the rudder and stick the hinge with
glue.Leave 1mm between the fuselage and
elevator,so that it can be
risen and down very flexible
13.Install the rudder angle and
stick it with glue14.Install the direction control lever of tail-
wheel and stick it with glue
18.S tick the chip of servo with glue
5

20.Install the fixed block of the wing
root and stick it with glue
23.Install aileron and stick
the hinge with glue. Leave 1mm
between the aileron and
wing,so that it can be risen and
down very flexible
22.Install aileron angle and stick it
with glue
21.I nstall the aileron push rod
19.Install the aileron servo
6
24. Shown as picture : the components of
nose landing gear wheel

26.Install the wheels into the landing gear.
25.Instal the wheels
27.Install landing gear EPP piece and
stick it with glue
28.Install the motor
29.Install the ESC 30.Install the hood
7

32.Install the shrouded screw
31.Install propeller base and propeller.
33.Install the direction push rod
34.I nstall the elevator push rod
36.C onnect the servo and esc line with
receiver,power-on and debug the plane.
Installation is finish, check again before the test flight to
make sure there is nothing abnormal before taking off.
35.Install the aileron push rod
8