Future FUMSLK54004A User manual

Electric Remote-controlled Model Aircraft
Installation Manual
敬告： 安装前请仔细阅读说明书。本产品非玩具， 必须在有经验人士指
导下进行安装和飞行。
Warning: Please read the instructions carefully before installation. This product is not a toy. It
must be installed and flown under the guidance of experienced personnel

打开包装时,请检查部件是否齐全,如有缺漏,请及时与经销商联系。
When unpacking, please check whether the parts are complete. If there is any missing, please
contact the dealer in time.
Setting of throwing:
Specification
：
Wingspan：965mm
Length：982mm
Wing Area：28dm2
Weight：670g（including battery）
Specification for reference：
Motor：Brushless 2217（2834）KV1250；
KV 1200 ESC: 30A
Battery：3S 11 . 1 V 25 c 1300 m Ah/14.8V 25c 1300mah
Plane Blade：10 x 4 . 7
Servo：9g*4
Servo Setting :
Aileron:
Flight Precautions
Please do not fly in the following environments:
1. Not in the wind. Poor visibility. Flying in bad weather such as rain.
2. Don't be in a crowd. High voltage line near the strong electromagnetic interference occasions flying.
3. Not in tall buildings. Forest street lights and other sundries to fly in the field.
4. If this is your first flight, please fly under the guidance of an experienced person
5. Remember, model aircraft are not toys and you are fully responsible for the safety of the flight.
Precautions for storage:
1. The battery must be removed during storage, otherwise it may explode and burn
2. After the flight, please do not squeeze the model when storing. It is better to hang it up
Note: Due to the continuous updating of the product, there may be small errors between the manual and the actual product.
2
Aileron : 40°/25°
Elevator: 40°/25°
Rudder: 40°/25°

1 .Shown as picture, Connect the elevator
servo with direction servo extension cable
3 .Put the connect line of elevator servo
& rudder servo into the fuselage
2 .Shown as picture, install the elevator
servo and rudder servo.
4 .Find out the undercarriage accessories
6. .Slowly and carefully insert the wings
into the fuselage,so that it is in the
center of the wings, using a ruler to
measure the same distance between
the side
3
5 .Put the undercarriage into the
fuselage and Insert landing gear retaining
board into landing gear and secure with
quick drying glue.

7. .,QVHUWWKHHOHYDWRUFDUHIXOO\DQG
VORZO\LQWRWKHIXVHODJH
9 .Use a ruler to measure the tail and the
wing ,keep them at the same distance.
8 .,QVHUWWKHIODWWDLOLQWRWKHIXVHODJH
FDUHIXOO\DQGVORZO\VRWKDWWKHIXVHODJHLV
SODFHGLQWKHFHQWHURIWKHIODWWDLO8VHD
UXOHUWRPHDVXUHWKHGLVWDQFHEHWZHHQWKH
WZRVLGHVWREHFRQVLVWHQW
10.The flat tails should be parallel
to the wings and perpendicular to
the sides of the fuselage.
4
11.Ensure that the Angle between the wing and
both sides of the fuselage is symmetrical, and the
contact position between the wing and the
fuselage is properly cemented with quick-drying
glue (note: do not use too much quick-drying glue,
it will corroded the foam inside).
12.Then use foam glue to reinforce the contact
between the wings and the fuselage

13.The contact position between the flat
tail and the fuselage should be properly
cemented with quick drying glue. (Note:
Do not use too much quick drying glue, it
will corrode the foam inside)
14.Then use foam glue to reinforce the flat
tail contact position with the fuselage.
15.Connect the elevator servo to the flat
tail and use the glue to fix hinge position.
(It is better to leave 1 mm space between
the elevator and the flat tail, so that the
elevator can move up and down flexibly)
16 .Install the rudder angle of aileron,stick it
with glue
17.Install the rudder angle of aileron,stick it
with glue
5
18. Install the tail wheel

19.Use quick - drying glue to fix the tail
wheel bracket to secure the wood pieces.
20.Install the rudder servo and glue the hinge
position with quick drying glue.(It is best to leave
1 mm spacing between the rudder and the
fuselage, so that the rudder can swing flexibly
from side to side)
21.Install ailerons and secure hinge
positions with quick drying glue. (It is
best to leave 1 mm space between
ailerons and wings, so that ailerons can
swing up and down flexibly)
23.Stick carbon fiber sheets as
needed to increase strength.
24.Stick the motor gasket
6
22.Install the aileron servo and secure hinge
positions with quick drying glue. (It is best
to leave 1 mm space between ailerons and
wings, so that ailerons can swing up and
down flexibly)

25. Install the motor 26 .Install ESC
28 .Cut 8 pc s of heat shrink tubes which the length
is 12 mm.
27 .Install the regulator on the servo arm.
29.Tighten the heat shrink tube with
fire and then stick with glue.
30.Connect the line of ESC with
receiver,and turn on the power to debug
the aircraft.
7

31.To adjust the ailerons, first adjust the
servo arm to 90 degrees with the push rod,
and then lock the regulator screw.
32.Adjust the rudder in the same
way as the aileron.
33.Adjust the elevator in the same way
as the ailerons.
34 .Find out the nose landing gear
wheel related components.
35.Install the wheel and wheel cover. 36 .To install the landing gear trim, apply foam
glue around it and clamp until the glue is
completely dry before releasing the clamp.
8

37.Install the hood and propeller,
and the installation is all complete 38.Install hood, propeller.
39.Before the flight, please check the
equipment and installation position
again to ensure safety and take off if
there is no abnormality.
9