Gaggenau AR 403 722 User manual

*DJJHQDX
Installation instructions3
Notice de montage15
Instrucciones de instalación28
AR 403 722
Exhaust Blower

2

3
en-us
Table of Contents
Installation instructions
9Safety Definitions 3
IMPORTANT SAFETY INSTRUCTIONS 4
Electric Safety 5
Appliance Handling Safety 7
Safety Codes and Standards 7
Related Equipment Safety 7
Proposition 65 Warning 7
General Notes 8
Ventilation line 8
Electrical requirements 8
For wall mounting: Checking the wall 8
Before you begin 9
Tools and Parts Needed 9
Parts Included 9
Appliance dimensions 9
Preparing Kitchen Units 10
Installation 11
Installing the appliance 11
Additional switching output 12
Connection for window contact switch AA 400 510 12
Networked operation 13
Connect Electrical Supply 13
Removing the appliance 13
Customer Service 14
Additional information on products, accessories,
replacement parts and services, as well as the Use and
care manual and the Installation instructions can be
found at www.gaggenau.com and in the online shop
www.gaggenau.com/zz/store
9Safety Definitions
SafetyDefinitions 9WARNING
This indicates that death or serious injuries may
occur as a result of non-observance of this
warning.
9CAUTION
This indicates that minor or moderate injuries may
occur as a result of non-observance of this
warning.
NOTICE
This indicates that damage to the appliance or property
may occur as a result of non-compliance with this
advisory.
Note: This alerts you to important information and/or
tips.

9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
READANDSAVETHESEINSTRUCTIONS INSTALLER: LEAVE THESE
INSTRUCTIONS WITH THE APPLIANCE
AFTER INSTALLATION IS COMPLETE.
IMPORTANT: SAVE THESE
INSTRUCTIONS FOR THE LOCAL
ELECTRICAL INSPECTOR'S USE.
Examine the appliance after unpacking it.
In the event of transport damage, do not
plug it in.
9WARNING
If the information in this manual is
not followed exactly, fire or shock
may result causing property damage
or personal injury.
9WARNING
Do not repair, replace or remove any
part of the appliance unless
specifically recommended in the
manuals. Improper installation,
service or maintenance can cause
injury or property damage. Refer to
this manual for guidance. All other
servicing should be done by an
authorized service provider.
9WARNING
WARNING – TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
▯Installation work and electrical
wiring must be done by qualified
person(s) in accordance with all
applicable codes and standards,
including fire-rated construction.
▯Sufficient air is needed for proper
combustion and exhausting of
gases through the flue (chimney)
of fuel burning equipment to
prevent back drafting. Follow the
heating equipment manufacturer’s
guideline and safety standards
such as those published by the
National Fire Protection
Association (NFPA), and the
American Society for Heating,
Refrigeration and Air Conditioning
Engineers (ASHRAE), and the
local code authorities.
▯When cutting or drilling into wall
or ceiling, do not damage
electrical wiring and other hidden
utilities.
▯Ducted fans must always be
vented to the outdoors.

5
9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
9WARNING
The applicable regulations of the
energy supply companies and the
regional construction regulations
must be observed when installing
the hood.
9WARNING
Risk of fire!
Operating several gas burners at the
same time gives rise to a great deal
of heat. The ventilation appliance
may become damaged or catch fire.
The ventilation appliance must only
be combined with gas burners that
do not exceed the maximum total
output of 61,000 BTU/hr (18 kW). If
41,000 BTU/hr (12 kW) is exceeded,
the local regulations concerning
room ventilation, room size, and
combination with ventilation devices
in exhaust and recirculating
operation must be followed.
9WARNING
To reduce risk of fire and to properly
exhaust air, be sure to duct air
outside. Do not vent exhaust air into
spaces within walls, ceilings, attics,
crawl spaces or garages.
9WARNING
To reduce the risk of fire, use only
metal ductwork.
9CAUTION
For general ventilating use only. Do
not use to exhaust hazardous or
explosive materials and vapors.
This appliance is intended for normal
family household use only. It is not
approved for outdoor use. See the
Statement of Limited Product Warranty. If
you have any questions, contact the
manufacturer.
Electric Safety
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the
event of an electrical short circuit,
grounding reduces the risk of electric
shock by providing an escape wire for the
electric current.
9WARNING
RISK OF ELECTRIC SHOCK!
Improper grounding can result in a
risk of electric shock. Consult a
qualified electrician if the grounding
instructions are not completely
understood, or if doubt exists as to
whether the appliance is properly
grounded.

9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
6
9WARNING
Risk of electrical shock or fire!
Frame grounded to neutral through a
ground strap. Grounding through the
neutral conductor is prohibited for
new branch-circuit installations
(1996 NEC), mobile homes, and
recreational vehicles, or in an area
where local codes prohibit
grounding through the neutral
conductor.
For installations where grounding
through the neutral conductor is
prohibited,
1. disconnect the link from the
neutral,
2. use grounding terminal or lead to
ground unit,
3. connect neutral terminal to lead
branch circuit neutral in usual
manner (when the appliance is to
be connected by means of a cord
kit, use a UL listed 4-conductor
cord for this purpose).
9WARNING
Before you plug in an electrical cord
or turn on power supply, make sure
all controls are in the OFF position.
If required by the National Electrical
Code (or Canadian Electrical Code), this
appliance must be installed on a separate
branch circuit.
9WARNING
To reduce the risk of fire or electric
shock, do not use this fan with any
solid-state speed control device.
Installer – show the owner the location of
the circuit breaker or fuse. Mark it for
easy reference.
Before installing, turn power OFF at the
service panel. Lock service panel to
prevent power from being turned ON
accidentally.
9WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE
FOLLOWING:
▯Use this unit only in the manner
intended by the manufacturer. If
you have questions, contact the
manufacturer.
▯Before servicing or cleaning unit,
switch power off at service panel
and lock the service
disconnecting means to prevent
power from being switched on
accidentally.
When the service disconnecting
means cannot be locked, securely
fasten a prominent warning
device, such as a tag, to the
service panel.

7
9IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Be sure your appliance is properly
installed and grounded by a qualified
technician. Installation, electrical
connections and grounding must comply
with all applicable codes.
9WARNING
Risk of electric shock!
Parts inside the appliance can have
sharp edges. The connection cable
can be damaged. Do not bend or
pinch connection cables during
installation.
Appliance Handling Safety
Safety Codes and Standards
This appliance complies with the latest
version of one or more of the following
standards:
▯UL 507 - Electric Fans
▯CAN/CSA C22.2 No. 113 - Fans and
Ventilators
It is the responsibility of the installer to
determine if additional requirements and/
or standards apply to specific
installations.
Related Equipment Safety
Remove all tape and packaging before
using the appliance. Destroy the
packaging after unpacking the appliance.
Never allow children to play with
packaging material.
The appliance should only be used if
installed by a qualified technician in
accordance with these installation
instructions. The manufacturer is not
responsible for any damage resulting
from incorrect installation.
Never modify or alter the construction of
the appliance. For example, do not
remove leveling legs, panels, wire covers
or anti-tip brackets/screws.
Proposition 65 Warning:
This product may contain a chemical
known to the State of California, which
can cause cancer or reproductive harm.
Therefore, the packaging of your product
may bear the following label as required
by California:
Hidden surfaces may have sharp
edges. Use caution when
reaching behind or under
appliance.

&DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY
67$7(2)&$/,)251,$352326,7,21:$51,1*
:$51,1*

8
en-us General Notes
General Notes
GeneralNotes Ventilation line
Note: The appliance manufacturer does not assume any
warranty for complaints attributable to the duct section.
▯The appliance achieves its optimum performance by
means of a short, straight exhaust air duct and as
large a duct diameter as possible.
▯As a result of long rough exhaust air ducts, many duct
bends or duct diameters that are smaller than 6"
(150 mm), the optimum extraction performance is not
achieved and fan noise is increased.
▯The ducts or hoses for laying the exhaust air line must
be made of non-combustible material.
Electrical requirements
This appliance must be properly installed and grounded
by a qualified technician in accordance with the National
Electrical Code ANSI/ NFPA 70 (latest edition) and local
electrical code requirements. IN CANADA: Electrical
installation must be in accordance with the current CSA
C22.1 Canadian Electrical Codes Part1 and/or local
codes.
The range must be connected to the proper electrical
voltage and frequency as specified on the rating plate.
For wall mounting: Checking the wall
▯The wall must be level, vertical and adequately load-
bearing.
▯Use suitable fasteners depending on the type of
construction (e.g. massive brickwork, drywall, porous
concrete, Poroton wall tiles).
▯The depth of the bore holes must be the same length
as the screws. The wall plugs must have a secure grip.
▯The maximum weight of the fan module is approx. 20 lb
(9 kg).

9
Before you begin en-us
Before you begin
Beforeyoubegin Tools and Parts Needed
▯Screwdriver Torx T20
▯Pencil
▯Drill with ¼" (6 mm) bit
▯Phillips head screwdriver
▯Jigsaw
▯Tape Measure
▯Tin snips
Note: Additional materials may be necessary for
installation in solid surface countertops. Contact the
countertop manufacturer.
Parts Included
Appliance dimensions
¡

ë



ʌʨʚ
 PP




ê


ë



 ʌʓʘ
é






çʚ

10
en-us Preparing Kitchen Units
Preparing Kitchen Units
Prepari ngKitchenUnits The stability of the fitted unit must also be guaranteed
after the cut-out work.
Make the cut-out in the bottom plate in accordance with
the installation drawing.
After the cut-out work is complete, remove the shavings.
Notes
▯The position of the cut-out can be varied according to
the local conditions.
▯The distance between the feet must be at least 20½"
(520 mm).
Note: For a toe-kick height of less than 5" (130 mm), an
opening towards the front must be created. This part of
the bottom plate can be reinserted after installation.



 PP










