Gamber Johnson 7160-1625 User manual

INST-1040
INSTALLATION INSTRUCTIONS
B
SAMSUNG XCOVER 5 CHARGING CRADLE
© Copyright 2019 Gamber-Johnson, LLC
Printing Spec:
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
7160-1625
PS-001
Form Product Revision
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
This instruction sheet is for the Samsung XCover 5 Charging Cradle only. For
with each individual product.
instructions on features, set-up, and operation of the phone, please refer to the
systems. Installation instructions for other Gamber-Johnson products are provided
manual provided by Samsung with the phone.
This cradle is designed to be used with a variety of Gamber-Johnson mounting
This instruction sheet is for the following products:
Item No.
7160-1625-10, (-S) Attached Power Cable with Bare Wire End
7160-1625-20 Attached Power Cable with Cig Adapter End
7160-1625-90, (-S) Cradle with No Electronics
1/5

practical.
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous
sparks resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-
Opening the docking station will void the product warranty.
damage, serious injury, or death.
docking station.
There are no adjustments required at any time of the electrical components within the
service of aftermarket vehicle equipment.
automotive electrical procedures and systems, along with proficiency in the installation and
To properly install a Gamber-Johnson docking station you must have a good understanding of
important to read and follow all instructions before installing this product.
Safety is dependent on the proper installation and servicing of this docking station. It is
installing.
WARNING: Failure to follow all safety precautions and instructions may result in property
anything that could be damaged.
PRE-INSTALLATION RECOMMENDATOINS
During Installation:
DO NOT connect this docking station to the vehicle battery until:
All other electrical connections are made1.
Mounting of all components is complete2.
Verification that no shorts exist in the entire system3.
DO NOT install equipment or route wiring or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all
electronic and software issues are resolved prior to installation:
Make sure the phone is operational by itself.1.
Insert phone into the docking station and verify that the phone is operating 2.
in the dock and the battery is charging.
Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
2/5

PART#/DATE LABEL
RELEASE BUTTON
LIVING HINGE
LATCH
AMPS PATTERN
STRAIN RELIEF
FOR CABLE TIES
POGO PINS
(USE PROVIDED HARDWARE)
FEATURE IDENTIFICATION
3/5
MOUNTING PATTERN

INSERTING AND REMOVING PHONE
2.) Use a zip tie (provided) to secure the cable.
4/5
CABLE MANAGEMENT
loop to avoid stressing the cable.
source. Press the cable into the strain relief slot on the back of the cradle, leaving a
1.) Connect the bare wire or cigarette plug end of the power cable to the power
the cradle.
1.) Insert the bottom of the
phone into the cavity of
the cradle.
2.) Rotate the top of the
phone and press until the
latch snaps over the front
of the phone.
1.) Press up on the release
button until the latch
clears the top of the
phone.
2.) Rotate the phone
forward and pull the
phone up and away from

including interfernece that may cause undesired operation.
ICES-003 Issue 7: Class B
Stevens Point, WI, 54481, USA, 715-344-3482
Regulatory Certification Information
Regulatory Model #: 7160-1625
Gamber-Johnson LLC, 5001 Joerns Dr.,
•
7160-1625-90, (-S)
7160-1625-20
GJ Model #'s: 7160-1625-10, (-S)
EN50498:2010
-90: CRADLE-SAMSUNG-XCOVER 5 NO ELECTRONICS
-20: CRADLE-SAMSUNG-XCOVER 5 POWERED, CIG ADAPTER
-10: CRADLE-SAMSUNG-XCOVER 5 POWERED, BARE WIRE LEADS
Descriptions:
•
Certifications:
EN55032:2015/AC:2016, Class B • VCCI-CISPR 32: 2015 • AS/NZS CISPR 32:2015 • FCC 47 CFR Part 15 Subpart B: Class B •
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
5/5