Gamber Johnson 7160-0410 User manual

Rev.M
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
If there is no factory front console plate
INSTALLATION INSTRUCTIONS
7120-0630(included) for required hardware
Product Revision
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Printing Spec: PS-001 FORD NGPI CONSOLE SEDAN & UTILITY, 2012
7160-0410, 7160-0412, 7170-0165, 7170-0166 INST-568
1/3
Form
(Top late) installed, use hardware bag
Note:
NOTE: ARMREST AND
CU HOLDER SHOWN
FOR REF. ONLY
© copyright 2016 Gamber-Johnson, LLC
12v Knockouts
Center Brace
Top late
Center Brace
USB/Audio
RELOCATION
Top late
12v Knockouts
Distributed By:

Sedan:
1. Remove the stock tunnel plate by emoving the
6 bolts.
2. The ha ness on the ight side of the YAW senso
(located on the t ansmission tunnel) may impede
box installation. Fo ease of installation, pull up
on ha ness to disconnect the push fastene
attaching the ha ness to the t ansmission tunnel.
3. The ea mounting points may be hidden unde
the floo ing. Ca efully cut the floo ing as shown
to expose the mounting points (Fig 1).
4. Slide console box into place.
5. Attach console to t ansmission tunnel using OEM
ha dwa e.
Fig 1 - Rea Mounting B acket, Ca pet Cut to Revel Th eaded Inse ts
Utility:
1. Remove the lowe dash t im panels on eithe side
of the dash (Fig 2).
2. Remove the stock tunnel plate by emoving the 6
bolts.
3. Remove the USB/Audio/12v jack T im Panel (Fig 2)
and disconnect the USB, Audio and 12v cables.
4. Relocate OEM Module to unde dash a ea (Fig. 3)
Fig 2 - Utility Lowe Dash
5. The ha ness on the ight side of the YAW senso
(located on the t ansmission tunnel) may impede
box insallation. Fo ease of installation, pull up
on ha ness to disconnect the push fastene attaching
the ha ness to the t ansmission tunnel.
6. Remove the Top Plate f om the console box.
7. Slide the console box into place.
8. Attach the console to the t ansmission tunnel using
the OEM ha dwa e.
9. Attach the Lowe Dash T im Panel to the console box
by placing the lowe lip of the T im Panel into the
hook on the bottom of the console box (Fig 4).
10. Attach the top of the Lowe Dash T im Panel to the
console box using the supplied T im Hooks (Fig 4).
Note that the left T im Hook has an "L" cut out of it.
It may be easie to emove the Top Plate when
installing the Lowe Dash T im Panels.
11. Snap the Lowe Dash Panels back into place.
2/3
Lower Dash
Trim anel
USB/Audio
Trim anel
Fig. 3 - OEM Module located on backside of trim anel

Sedan and Utility:
Install the a m est (7160-0409 & 7160-0411) into the tube and adjust to the desi ed
height/o ientation then tighten the bolt unde the a m est. Note: A m est is not included with
7160-0410 o 7160-0412 but can be o de ed sepa etly. The a m est mounting b acket can be
flipped ove to lowe the a m est if desi ed o if used with a P inte A m est.
The cup holde (MCS-INTCUP) can be placed anywhe e along the ho izontal length of the box.
Note: The cup holde is not included with 7160-0410 o 7160-0412 but can be o de ed sepa etly.
The Top Plate and Cente B ace on both console boxes a e designed to be emovable to aid in
installation and cable outing. If eithe item is emoved Gambe -Johnson ecommends
einstalling the sc ews with a d op of Blue 242 Loctite to p event loosening. To que the (4) top
plate bolts to 65-80 in-lbs when einstalling.
Both boxes have knockouts fo 12v accesso y outlets (7160-0063). To install simply punch out
the desi ed knockout and install the 12v outlet. The 12v outlet will need to be ha dwi ed into
the vehicles powe system. An additional 12v accesso y outlet can be pu chased fo the second
knockout if desi ed.
3/3
Lower Dash Trim anel
Hooked into Console Box
Left Trim Hook
Fig 4 - Installing Lowe Dash
T im Panels