Gametime Tire Swing User manual

ASSEMBLY DRAWING
Enriching Childhood Through Play
OCMCAPLAY EOR
SM
R
PA N Y
ISSUED/REVISED:
1−800−235−2440
INSTALLATION
PARTS LIST
DETAIL
REFERENCE
=
=
R10777
TIRE
SWING
06/20/05
NOTE: 10778 ADD−A−BAY
10777 SHOWN
3
1
3
2
113
113
562
114
116
0'-12 1/2" [31.75cm]
FROM FINISHED SURFACE
TO BOTTOM OF TIRE
6'-8"[203.20cm]
FINISHEDSURFACE
COFTOPRAIL
L
NOTE: REGULAR MAINTENANCE
REQUIRES LUBRICATION OF SWIVEL
ASSEMBLY WITH STANDARD
AUTOMOTIVE GREASE. A GREASE
FITTING IS INCLUDED IN THE
SWIVEL ASSEMBLY FOR THIS
PURPOSE. IN AREAS OF HIGH USE,
LUBRICATION INTERVALS SHOULD
BE INCREASED ACCORDINGLY.
STEP 1: Before assembling this equipment,
read the enclosed Installer Instructions in the
installation booklet; follow all the instructions
during installation.
STEP 2: Assemble parts as shown in the
Assembly Drawing. Refer to the assembly
details for the specific hardware required in
each connection.
STEP 3: Loctite (supplied by others) should be
used on all threaded hardware.
INSTALLATION
INSTRUCTIONS
YEARS OLD

PAGE 2
10778 SHOWN
ASSEMBLY DRAWING
1
5
2
EXISTING TOPRAIL
ASSEMBLY
114
116
562
113
0'-12 1/2" [31.75cm]
FROM FINISHED SURFACE
TO BOTTOM OF TIRE
6'-8"[203.20cm]
FINISHEDSURFACE
COFTOPRAIL
L
EXISTING UPRIGHT
NOTE: REGULAR MAINTENANCE
REQUIRES LUBRICATION OF SWIVEL
ASSEMBLY WITH STANDARD
AUTOMOTIVE GREASE. A GREASE
FITTING IS INCLUDED IN THE
SWIVEL ASSEMBLY FOR THIS
PURPOSE. IN AREAS OF HIGH USE,
LUBRICATION INTERVALS SHOULD
BE INCREASED ACCORDINGLY.
113
1/2" x 1-1/4" P.B.H.C.S. w/ Patch
Bracket
Warning: During Installation, Hardware And Small Parts Are Choking Hazards
For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed.
Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment
And Dispose/Save Them In A Secure Location.
PARTS LIST
1/2" Hex Nut
1/2" x 5-1/2" B.H.C.S.
1/2" Lockwasher
Toprail Ass'y.
Hardware Complete
3/8" 'S' Hook
3/8" Lockwasher
3/8" Lock-Nut
Swing Swivel
Arch Uprights
Add-A-Bay Arch Upright
Tire Ring Frame
Chain (44-1/8" Lg.)
Plastic Tire
3
4
5
REF.
NO.
1
2
DESCRIPTION
22 812062*
2
4
4
2
4
4
817342*
811071*
804055*
10778
02
3
6
1
3
3
3
6
1
3
3
1
3
1
0
1
3
1
1
10777
NO. REQ'D
1
1
1
1
140434
1*
817334*
303833*
804353*
159194*
176318*
156872
140492
304005
NUMBER
PART
140364
300196
"U" Bolt 3 3 803437*

PAGE 3
14'-5 9/16" [440.85cm]
4'-1" [124.46cm]
15'-0 3/8" [458.08cm]
14'-5 9/16" [440.85cm]
4'-1" [124.46cm]
15'-0 3/8" [458.08cm]
EXISTING
UPRIGHTS
10778
GROUND PLANS
NOTE: HOLE DEPTHS INDICATED
ON ALL GROUND PLANS ARE
MEASURED FROM THE FINISHED
SURFACE. SEE DETAIL 005. ALL
FOOTING DIMENSIONS ARE BASED
ON LEVEL FINISHED SURFACE.
10777
2'-0" [60.96cm] DIA. x
2'-6" [76.20cm] DEEP
(4 REQUIRED)
SEE DETAIL 005
2'-0" [60.96cm] DIA. x
2'-6" [76.20cm] DEEP
(4 REQUIRED)
SEE DETAIL 005
CONCRETE REQUIRED:
(PER GROUND HOLE)
.17 CUBIC YARDS
[.13 CUBIC METERS]

IMPORTANT
TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F1487, ANY BOLT END
PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT -OFF FLUSH, F ILED
SMOOTH AND TREATED TO PREVENT CORROSION.
NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE.
13
DETAILS −for−
10 INCH
0CM 123 645 78910 1211
PAGE
14 15
23456
10777 & 10778
5

PAGE 4
NOTE:
1.) OWNER/OPERATOR SHALL INSTALL AND
MAINTAIN PROTECTIVE SURFACING WITHIN THE
USE ZONE (U.S.) OR PROTECTIVE SURFACING
ZONE (CANADA) OF ALL PLAY EQUIPMENT TO
COMPLY WITH ASTM F-1292 AND ASTM F-1487
(U.S.) or CAN/CSA-Z-614 (CANADA).
2.) SOLID OUTSIDE BORDER REPRESENTS
MINIMUM REQUIRED ASTM USE ZONE AND CSA
PROTECTIVE SURFACING ZONE FOR SWING
FRAME SHOWN.
3.) DASHED LINES REPRESENT CSA
NO-ENCROACHMENT ZONE (CANADA ONLY).
4.) *EACH ADDITIONAL CONNECTED SWING
FRAME BAY INCREASES THE USE ZONE
SURFACING DIMENSIONS BY 14'-5 9/16" [4.41M].
(NOT AVAILABLE IN CANADA).
TOP VIEWS
10778
10777
[1.80M] ALL AROUND
14'-5 9/16" [4.41M]
4'-6" [1.37M]
11'-0" [3.35M] RADIUS
(TYPICAL)
5'-10 7/8" [1.80M] RADIUS
(TYPICAL)
*38'-6 1/16" [11.74M]
33'-9 3/4" [10.31M]

IMPORTANT
TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F1487, ANY BOLT END
PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT -OFF FLUSH, F ILED
SMOOTH AND TREATED TO PREVENT CORROSION.
NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE.
13
DETAILS −for−
10 INCH
0CM 123 645 78910 1211
PAGE
14 15
23456
10777 & 10778
6