Graco OASIS User manual

OASISTM SWING
with SOOTHE SURROUNDTM Technology
PD348757C 9/15

2
2-A Parts list
2-B Features on Certain Models
1 WARNING
2 Features
Pages 4-15
Pages 16-17
3-A Seat Assembly
3-B Assembling Swing Frame
3-C Installing Seat
3 Assembly Pages 18-25

3
4-A To Adjust Recline (2 positions)
4-B To Secure Child
4-C Installing Batteries (not included)
4-D To Use Wall Plug
4-E Starting Swing (6 Speed)
4-F To Use Vibration
4-G Problem Solving
4 Use Pages 26-41
5-A Care and Maintenance
5-B Replacement Parts • Warranty Information (USA)
5-C Product Registration (USA)
5 Cleaning Pages 42-44

4
Prevent serious injury or death: Failure to follow these
warnings and the assembly instructions could result in serious
injury or death.
•PLEASE SAVE OWNER’S
MANUAL FOR FUTURE USE.
•THIS PRODUCT REQUIRES
ADULT ASSEMBLY. Follow
assembly instructions
carefully. If you experience any
difficulties, please contact the
Customer Service Department.
•TO PREVENT SERIOUS
INJURY OR DEATH FROM
INFANTS FALLING OR BEING
STRANGLED IN STRAPS:
• Always secure infant in the
restraint system provided.
After fastening buckles,
adjust belts to get a snug fit
around your infant.
• Never leave infant
unattended in swing.
• Never carry swing with infant
in it.
• Discontinue use of swing
when infant attempts to climb
out or reaches 30 pounds
(13.6 kg).
• Keep swing seat fully reclined
until child is at least 4 months
old AND can hold up head
without help. Young infants have
limited head and neck control. If
seat is too upright, infant’s head
can drop forward, compress the
airway, and result in DEATH.
STRANGULATION HAZARD:
•DO NOT suspend strings
over the product or attach
strings to toys.
•DO NOT place product in any
location where there are
cords, such as window blind
cords, drapes, phone cords,
etc.
•Strings can cause
strangulation. DO NOT place
items with a string around
your child’s neck, such as
hood strings or
pacifier cords.
•DO NOT USE THIS PRODUCT if
it is damaged or broken.
•NEVER USE as a car seat.
READ ALL INSTRUCTIONS
BEFORE ASSEMBLY AND
USE OF THIS PRODUCT.
FALL HAZARD:
To prevent serious injury or death
from falling :
• Never leave child unattended.
• Always use restraint system.
Adjust belt as needed to get a
snug fit around your child.
• Never use for a child able to sit
up unassisted.
• NEVER use this product as a
means to transport an infant in a
motor vehicle.

5
•DO NOT use the AC adapter if it
has been exposed to
liquids, has been dropped,
or is damaged.
• Protect the power cord. Place it
so it is not walked on or pinched
by furniture or other items.
•DO NOT use with an
extension cord.
• Use only power cord
provided.

6
FOR SAFE BATTERY USE:
Keep the batteries out of children’s reach.
Any battery may leak battery acid if mixed with a different battery
type, if inserted incorrectly (put in backwards) or if all batteries are
not replaced or recharged at the same time. Do not mix old and new
batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable
(nickel-metal hydride, nickel-cadmium) batteries.
Any battery may leak battery acid or explode if disposed of in fire or
an attempt is made to charge a battery not intended to be recharged.
Never recharge a cell of one type in a recharger made for a cell of
another type.
Discard leaky batteries immediately. Leaky batteries can cause skin
burns or other personal injury. When discarding batteries, be sure to
dispose of them in the proper manner, according to your state and
local regulations.
Remove batteries before storing product for a prolonged period of
time. Batteries left in the unit may leak and cause damage.
Recommended type batteries—alkaline disposables,4-D (LR20-1.5V),
and 3-C (LR14-1.5V). NEVER mix battery types. Change batteries
when product ceases to operate satisfactorily.

7
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device,pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is needed.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. CAN ICES-3 (B) /NMB-3
(B).

16
2-A Parts list
This model may not
include some
features shown
below. Check that
you have all the
parts for this model
BEFORE assembling
your product. If any
parts are missing,
call Customer
Service.
Tools required:
Phillips Screwdriver
ALL MODELS
FEATURES ON CERTAIN MODELS
Styles vary
2X
4X

17
2-B Features on Certain Models
Only use this head support on this
swing. Never use this head support
on any other product.
This model may
not include some
features.
DO NOT use any
other accessories
with this product.
Head support
Styles vary

18
3-A Seat Assembly
4X
1. Pull the seat pad off the top
portion of the shell.
2. Pull the seat pad off the bottom
portion of the shell.

19
3. Turn shell over and fasten
vibration unit to shell with 4
screws as shown.
4. Wrap the bottom portion of the
seat pad around the bottom of the
shell as shown.
5. Wrap the top portion of the seat
pad around the top of the shell as
shown.

20
7. Wrap canopy over back of
bouncer and attach fastening
strips.
8. Attach toys as shown.
Styles vary
2X
6. Insert canopy legs into slots in
the shell.
SNAP!

21
3-B Assembling Swing Frame
1. Place carton on ground. Lay unit
down as shown. Plug wires
together as shown and insert
wires inside tube.
2. Insert motor housing tubes to leg
tubes as shown.
SNAP!

22
SNAP!
3. Insert vertical tubes into base
tubes as shown.
SNAP!

23
4. Grab base tubes and push down
while inserting tubes together.
5. Place the cover on tubes as
shown.
Installation complete.

24
3-C Installing Seat
1. Insert rectangle end of the hanger
tube into motor housing. Repeat
for other hanger tube.
CHECK that hanger tube is
secured in housing by pulling
firmly on it.
SNAP!

25
2. Insert hanger tube into seat
mounts on sides of seat. Repeat
for other hanger tube.
CHECK that hanger tube is
secured in housing by pulling
firmly on it. SNAP!
Installation complete.

26
4-A To Adjust Recline (2 positions)
1. Squeeze both tabs on the side of
the seat and rotate up or down.
Use the most reclined position for newborn and young babies. Use the more
upright position for older, more active infants.

27
4-B To Secure Child
WARNING Falling Hazard: Always use the seat belt.
1. To open, press button on buckle
to release the waist straps.
2. To close, slide shoulder strap
connectors to waist straps and
insert into buckle.

28
3. Use slide adjuster at shoulder and
waist for tighter adjustment.
4. To change harness slots, pull the
seat pad off the top portion of the
shell.
5. Pull harness straps out of
harness slots in the pad and thread
into the new harness slots.
Make sure both straps are either in
the lower or upper slots.