GAPOSA QCXSUN User manual

Funk-Sonnensensor, 1-Kanal
mit Saugnapfbefestigung an der Sheibe
QCXSUN
GAPOSA srl
via Ete, 90 - 63900 Fermo - Italy
T. +39.0734.22071 - F. +39.0734.226389
[email protected] - www.gaposa.com QCXSUN_ML_1014

QCXSUN was developped for all GAPOSA radio motors installed in interior/exterior blinds or roller shutters.
NOTE: Before starting the programming procedure it is necessary to check which interior blind, exterior blinds or
roller shutters will be controlled by the sun sensor.
1. HOW DOES IT WORK
SENSOR OFF. The sensor is completely inactive. It does not measure light intensity nor transmits radio signals.
SENSOR ON. The sensor measures light intensity every 90 seconds (1 ash of the LED).
NOTE: When the battery is inserted for the rst time , the default factory setting of the sun sensor is OFF with a
threshhold of 1 (low light)
2. FUNCTIONS
When the sensor detects an increase in brightness
(above the threshold) it closes the blind/shutter
and stops measuring light intensity for 20 minutes
before starting again every 90 sec.
When the sensor detects a decrease in brightness
(below the threshold) it opens the blind/shutter and
stops measuring light intensity for 1 minute before
starting again every 90 sec
led
front rear
suction
cup
1
2
3
OFF - Disables the sun sensor (1 slow ash)
ON - Activates the sun sensor (3 quick ashes)
SEL - Sun sensibility threshold adjustment

QCXSUN
2. PROGRAMMING QCXSUN
1 2 3
1Press and hold PROG-TX button of the MASTER
transmitter till the motor starts moving
2Check the motor rotation then release Prog-TX
button
3Press 1+2 (if motor move UP) or 2+3 (if motor move
DOWN) button of the QCXSUN
Transmitter is now programmed
3. SUN SENSIBILITY THRESHOLD ADJUSTMENT
1. Press and hold BUTTON 3 (the LED will turn on at rst) until the LED starts to ash slowly,
release BUTTON 3
2. Adjust the threshold by using BUTTONS 1 and 3 which will allow you to either increase
(Button 1) or decrease (Button 3) the threshold.
Whenever a button is pressed the LED ashes according to the level of sun threshold (1,
2 or 3).
Threshold 1 - 5 Klux (default) = Low light (most sensitive) > led ashes 1 time
Threshold 2 - 30 Klux = Med Light > led ashes 2 time
Threshold 3 - 60 Klux = High light (less sensitive) > led ashes 3 time
3. Once the desired threshold has been obtained press BUTTON 2 to conrm.
NOTE: It is important to program the sun sensor’s threshold within 30 seconds or the time
out function will automatically exit the programming procedure without saving the new
threshold.
Led
flashes
slowly
Press 1
to increase
the threshold Press 3
to decrease
the threshold
Press 2
to confirm
threshold
1 2 3
IMPORTANT: QCXSUN sensor can only be programmed once the radio motor has already been
programmed to a transmitter.

4. ADDITIONAL FUNCTIONS (AS A NORMAL TRANSMITTER)
Buttons 1+2= opening command to programmed blinds/shutter;
Buttons 2+3 = closing command to programmed blinds/shutters.
5. REPLACING THE BATTERY
1. Remove the rubber band, the screw and the back cover;
IMPORTANT: While replacing the battery, it is extremely important to be very careful
and to not damage the sun sensor.
2. Take out the electronic board and remove the battery;
3. Position the battery (CR2450) according to polarity;
4. Reinstall the back cover, the screw and the rubber band.
OPEN
1 2 3
CLOSE
check polarity
IMPORTANT: While
replacing the battery, it
is extremely important
to be very careful and
to not damage the sun
sensor.
rear