Garden Treasures 226390 User manual

Item # 226390
BRICK WALL FOUNTAIN WITH SUBMERGED LIGHT
Questions, Problems, Missing Parts? Before returning to retailer,
call our customer service department at 1-866-728-6187, 9a.m. –
5p.m. EST (Mon.-Sat.) or email [email protected].
Parts List Tools Required for Assembly
Part # Description Quantity •No tools required
A Fountain 1pc
B Pump 1pc Preparation
C Submersible Lamp 1pc
D Transformer 1pc
E Pump Hose 1pc
F Resevoir 1pc
Before beginning assembly, read all warnings and safety precautions.
Remove parts from carton. Compare parts with parts list. If any part is
missing or damaged, do not attempt to assemble or use the product.
Contact customer service for replacement.
Special Warnings
To reduce risk of electric shock, connect only to a properly grounded outlet.
Inspect cord for damage before installation, maintenance or use. If damage is found, replace entire pump/cord assembly.
Do not exceed voltage shown on pump.
Never submerge transformer under water.
Safety Precautions
1. Use proper power source as indicated on the pump label.
2. Keep cord away from high temperatures and sources of heat.
3. Keep fountain out of the reach of children.
4. If in a freeze area, remove water from base and statuette.
5. Remove and store statuette and pump indoors in freezing weather conditions.
6. Always disconnect pump from electrical outlet before handling.
7. Do not let pump run dry.
8. Do not lift pump by its power cord.
9. Do not pump heated liquids.
10. Operate in freshwater only.
11. Pump must be completely submerged for proper operation and cooling.
Care and Maintenance
1. Keep water clean. Distilled water will reduce mineral deposits and improve water clarity.
2. Clean product periodically to prevent mineral deposits and contamination.
3. Disconnect power and empty basin if fountain will not be used for an extended time.
4. If installed outdoors and in a freeze area of the country, make certain all water has been removed from the fountain and it is dry. The
product should not be operated in temperatures below 41º Fahrenheit (5º Celsius). Freeze damage could occur.
5. To eliminate possible water damage to floors and other areas around the fountain, check for leaks and excessive splashing after initial
setup.
6. Place fountain in a location that will not be damaged should the area come in contact with liquids.
7. Do not leave fountain running unsupervised for extended periods of time.
8. Check areas surrounding fountain on a regular basis for leakage.
1
Assembly Instructions

Estimated Assembly Time: Approximately 10 minutes
Note: Assemble fountain on a level surface.
Make certain all connections are secure.
1. Attach pump hose (E) to pump (B) and place the pump flat in
the reservoir. Place the submersible lamp (C) in a proper place
in the front of the reservoir. Run the pump cord out through the
notch at the back panel.
2. Hang fountain (A) on wall using the hook on back of fountain.
3. Add clean water into the reservoir. The water level should be
approx. 1” below the edge of the reservoir.
4. Attach pump cord to transformer (D), plug the transformer into
an outlet. Switch on and your fountain will start to function as
intended. Water will flow out from the fountain bonsai
(Note: To prevent splashing, wet the watering surface before
using.) with light on the watering surface. You can adjust the
direction of light to beautify the illumination.
Submersible Lamp Assembly Diagram
NOTE: Diagram shown is for illustrative purposes only.
Troubleshooting Guide
Problem Remedy
Pump operates, but there is no
water flow. 1. Make certain pump is fully submerged. 2. Make certain pump hose has no kinks.
Pump operates, but there is no
water flow and pump is fully
submerged and pump hose has no
kinks.
1. Remove pump hose from pump outlet.
2. Clean pump hose.
3. Set pump in water (outlet side up).
4. Once water begins to flow, reattach pump hose.
Printed in China
Model No. F41062CA
2