Garden Treasures MZ14027GA User manual

1
ITEM #0880319
LIGHTED 3-TIER FOUNTAIN
MODEL #MZ14027GA
ATTACH YOUR RECEIPT HERE
SerialNumber PurchaseDate
Question, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Friday.
Espaňol p. 7
AB17897
Garden Treasures® is a registered
trademark of LF, LLC. All rights reserved.

2
PACKAGECONTENTS
PART DESCRIPTION QUANTITY
A Top 1
B Top bowl with light 1
C Middle bowl with light 1
D Big bowl spacer 1
E Big bowl with pump 1
F Fountain base 1
G Pipe 1
H Rubber gasket 1
I Thread 1

3
SAFETYINFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
CAUTION: As with any large container of water, fountains are to be used carefully with adult
supervision. They are not intended to be used as “kid pools” and present a risk to small children and
infants. Injury or accidental drowning could result. In addition, as with any electrical appliance, make
sure the pump plug is dry before you plug it into an outlet, and make sure you are not standing in the
water - electrical shock could result. Filled fountain weighs a considerable amount. Make sure
your set-up area can support at least 300 lbs.
For best results – Install the fountain on a flat, level surface close to an electrical outlet.
Place the fountain in a location where any water spills or splashing will not reach any other electrical
equipment or cause damage.
Choose an appropriate location before installing the fountain. DO NOT lift or push/drag the water
basin to relocate the fountain when it’s filled with water. Empty the water basin before lifting.
Excessive weight or pressure on any of the fountain sections may cause it to tip or fall over. Keep
pets and children away from any of the fountain sections.
Some splashing may occur. To avoid injury from electrical shock, observe basic safety precautions
and comply with the following instructions:
The pump on the fountain has no user serviceable parts. Only an authorized service representative
should service the pump. Do not open the sealed pump housing as this may result in electrical
shock. Refer to enclosed pump maintenance guide for cleaning.
Always unplug the pump from the electric outlet before cleaning and handling.
Use with clean water only. Do not place it in other liquids. Do not allow the pump to run dry.
An adult should supervise children when they are around the pump.
Use the proper power source as indicated on the pump label.
Equip the electrical power for the pump with a ground fault circuit interrupter (GFCI).
Keep the fountain away from high temperatures or heat sources.
Do not use the pump in water above 86°F.
Disconnect the power cord from the outlet by holding the plug. Do not lift, carry, or pull the pump
by the power cord.
If the entire fountain falls into the water accidentally, turn off the circuit breaker immediately.
If any leakage occurs around the pump housing, turn off the circuit breaker immediately and
have the pump serviced by a registered technician.
Do not operate the fountain if the pump has been dropped or has a damaged power cord or plug.
Do not replace the power cord.
Keep the plug dry. Do not expose the plug to water or steam. Do not use the pump in swimming
pool or marine area.
If the plug or the wall receptacle gets wet due to water dripping down the power cord or for any
other reason, do not remove the plug from the wall outlet until
the circuit breaker is turned off.
NOTE: Allow the pump power cord to hang at a lower level
than the wall outlet to form a “drip loop.” This will help
prevent water from dripping down the power cord and
getting into the wall outlet.
Do not expose the pump to direct sunlight or to low
temperatures for any period of time.
Use only a UL-approved extension cord of the correct rating to avoid overheating.
Do not use attachments that are not provided by the manufacturer since they may cause an
unsafe condition.
Do not use the pump for anything other than its intended use.
GFCI DRIP LOOP

4
ASSEMBLYINSTRUCTIONS
1. Place the big bowl with pump
(E) on the fountain base (F) and
turn clockwise to secure
together.
1
2
3
4
5
6
7
8
9
10
2. Run the cord from pump (J,
preassembled) through the tube
on the big bowl (E) to come out
from the bottom of fountain
base (F).
Make sure the preassembled
pump is set to the maximum
water flow position (indicated by
a plus sign “+”).
3. Screw pipe (G) into mounting
bracket on pump (J).
4. Place big bowl spacer (D) on
the big bowl (E).
Run the two female plugs
coming from pump (J) through
the center of big bowl spacer
(D) as shown.
5. Connect the short female plug from
the pump (J) to the male plug found
on the middle bowl with light (C) and
screw the preassembled ring over the
cable to secure the connection.
Then place the middle bowl on the big
bowl spacer (D). Run the long female
plug from the pump through the
center of the middle bowl as shown.
7. Secure the fountain with
rubber gasket (H) and top
(A).
8. Pour water gently into big
bowl (E), middle bowl (C)
and top bowl (B).
10. OPTIONAL: To reduce
excess splashing and increase
flow time, a length of thread
(I) can be used to help direct
the water flow gently to the
bowl below. Cut a length of
thread (16 in. for top bowl, 24
in. for middle bowl) and place
each of the threads on
adjacent spouts as shown so
that the ends will hang down
into the bowl below.
9. Plug the pump (J) into a
power supply.
6. Connect the long female
plug from the pump (J) to the
male plug found on the top
bowl with light (B) and screw
the preassembled ring over
the cable to secure the
connection. Then place the
top bowl on the middle bowl
(C).

5
CARE AND MAINTENANCE
Check regularly that the water reservoir has sufficient water to cover the pump at all times. It will be
necessary to check more frequently in warm or windy weather.
Do not allow the pump to freeze. During cold spells, remove the pump from the water feature and
place in a water-filled container in a frost-free position. DO NOT store the pump dry.
Periodically it will be necessary to change the water and clean the water feature and reservoir. The
frequency of this will depend on the weather and location of the water feature. The outside of the
water feature can be cleaned using a soft cloth and clean water and the reservoir with a soft brush.
A mild detergent can be used, but please note this will cause the water to foam and should be
avoided unless strictly necessary.
The pump rotor will require cleaning at approximately monthly intervals. A good indication will be if
the water flow rate drops. Unplug the water feature, remove the pump from the water reservoir and
disconnect the water pipe. Remove the filtering cover and pressure-casing from the front of pump
body. Clean the rotor and housing in clean water using cotton buds. Reassemble the pump,
reconnect the water pipe and reassemble the water feature.
Replacing the light.
Step 2: Take off the light.
Step 1: Unfold the light clamp gently
to remove light from the fountain
body.
Step 3: Insert a new light into the light clamp.
NOTE: To acquire replacement lights, please
refer to the Replacement Parts section. Only
use the lights available for order there as
replacements.