GARDINER TECHNOLOGY GARDTEC 300 Series User manual

Gardiner Technology Ltd
Rochdale
United Kingdom
QUALITY . INNOVATION . TECHNOLOGY
PR2897 REV2.1
:I
]
!
I:
I
I .-I - • • I
@£[ru[Q)1f~©
$)@@ ~~000~~
GARDTEC 350
User Instructions
\

GARDTEC 350
Contents
Introduction 1
Setting the System 2
Part Setting the System 2
Unsetting the System 3
Resetting after an Alarm 3
. User Programming Mode 3
Removing Individual Zones 5
Testing the System 7
Reading the Log 8
Turning Chime On and Off 9
Programming User Codes 10
. Care and Service of Your System 12
Terminology 12
Installers Details 13
Service Record 13
Users Manual
GARDTEC 350
users Manua1
GARDTEC 350 USER INSTRUCTIONS
INTRODUCTION
Your Gardtec 350 Control Panel will have been fully programmed by your installation
engineer to suit your needs. Normal day to day operations will consist of the following:-
Fully setting the system
Part setting the system
Unsetting the system
Display is given via eight individual
LE.Os. When using the Gardtec 350 in it's normal
user mode the bold black legend is used, this
is shown in Fig 1. below.
Fig 1.
POWER CJ
DAY CJ
Z1 CJ •·
Z2CJ
Z3 CJ ,ir ..
Z4CJ
ZSo ~
TAMPER CJ
A key press tamper will activate if more than 24 invalid digits are entered. This
will cause an internal alarm if the unit is unset and a full alarm if the unit is set.
Keys 1 and 3 have been factory programmed for P.A (Personal Attack). This is a 24
hour function and will operate if the control panel is set or unset.
To use the keypad
P.A function press and hold keys 1 and 3 at the same time, the alarm will then activate.
To stop the alarm sounding enter a valid user code. After the keypad P.A function has
been used the system will require resetting as shown on page
3.
Page 1

GARDTEC 350
Users Manual
SETTING THE SYSTEM
To Fully Set the system proceed as follows:-
1)
2)
Enter a valid User code.
Leave the premises via the
authorised exit route.
(The DAY LED will flash followed
by the exit tone.
Any zones violated during exit will change the
exit tone and the appropriate L.E.D will indicate).
Note: To abort setting during exit time re-enter the code.
PART SETTING THE SYSTEM
To Part Set the syste~ proceed as follows:-
1)
2)
3)
Enter a valid User code. (The DAY LED will flash followed by the
exit tone).
If Part Set 1 is required Press 1 or (The DAY LED will flash slowly. Zones
programmed as Part 1 will be removed)
If Part Set 2 is required Press 2 or (The DAY LED will flash slowly. Zones
programmed as Part 2 will be removed)
If Part Set 3-is required Press 3 (The DAY LED will flash slowly. Zones
programmed as Part 1 and Part 2 will
be removed).
Leave the premises via the authorised exit route (or retire to an unprotected
area).
Note: If any of the above part sets have been programmed as silent by your
engineer the setting will be silent with a single beep as the system final-
ly sets.
Page 2
1
·I
GARDTEC 350
UNSETTING THE SYSTEM
Users Manual
To Unset the system proceed as follows:-
1)
2)
3)
Enter the premises via
an authorised entry point (the entry tone will sound).
Proceed directly to the Control Panel and enter a valid
User code (the entry
tone wifl stop and the
DAY LED will illuminate).
If
the alarm has been activated during the set period all the LEDs will flash
press
NO to view the cause of alarm.
RESETTING AFTER AN ALARM
If the system is set, unset it as shown above and proceed as follows:-
1)
2)
After an alarm all the LEDs will be flashing. If you wish to view the cause of
alarm press NO. To Reset the system enter the Master code and start to set
the system.
Before the entry time expires
enter a valid code to abort the setting. The
system is now reset.
USER PROGRAMMING MODE
To enhance the flexibility of the Gardtec 350 Control Panel there are five user pro-
grammable options available. When programming the User options the display is via
the five
Zone L.E.Ds and the White legend is used. This is shown in Fig 2. below. It
should be noted the the user programming mode is only available
to the Master user
(User 1
).
Fig 2.
POWER □
DAY □
Z1 D f]T:fWi'i=I
Z2D
Z3 D l~~
Z4D
zs □ f:1:rim ,m,
TAMPER D
Page 3

GARDTEC 350
The User programmable options are as follows:-
!Aemove
Users Manual
This option enables the Master user to Remove individual zones when setting the sys-
tem. This is in addition to any part set suites pre-programmed
by your engineer.
Tes ft
This option allows the Master user to Test the system.
log
This option allows the Master user to view the event Log.
C~ime
This option allows the Master user to turn the Chime option On and Off. (The zones
that are on chime will have been programmed by the installation engineer).
Program (Codie}
This option allows the Master user to change the Codes for the Master user (User1 ),
User (User2) and Set only user (User3) levels.
When programming the
User options the LEDs may show the following status:-
Fig 3.
CJ OFF
•ON .
~~
FLASHING
To program the options shown above proceed as follows:-
Page 4
GARDTEC 350
Users Manual
REMOVING INDIVIDUAL ZONES
1)
2)
3)
With the Control panel in the DAY mode (Unset) enter the Master code. The
exit tone will sound.
Before the exit time expires Press NO. The exit tone will silence and the
Remove LED will flash as shown iri Fig 4.
Fig 4.
POWER □
•1:41
Press YES to program the IRlemove option. The display will sliow as Fig 5.
Fig 5.
POWER . CJ
DAY CJ
Page 5

GARDTEC 350
users Manua1
4)
5)
6)
Press the key corresponding to the zone you wish to remove followed by the
YES key (a comfort tone will be generated if all is okay). If you make a mis-
take and remove the wrong zone repeat the operation from step 3 but press
NO after the zone number.
If you wish to remove more zones repeat from step 3.
When you have finished removing the required zone(s) press the Okey to
escape programming .mode. ·
Note: This operation should be carried out each time you wish to remove
individual zones. If you remove the same zone(s) on a regular basis ask
your engineer to put them in a part set suite.
Page 6
1
J
l
GARDTEC 350
TESTING THE SYSTEM
users Manua1
1)
2)
3)
With the Control panel in the DAY mode (Unset) enter the Master code. The
exit tone will sound.
Before the exit time expires Press NO. The exit tone will silence and the
IR!eimove LED will flash.
Press NO and the
Tes1t LED will flash as shown in Fig 6.
Fig 6.
POWER CJ
DAY CJ
4) Press YES to select the Tes1t option and the flashing Tes1t LED will illumi-
nate steadily.
5) You may now "walk test" the system. Any zones that are violated will
generate a tone and the appropriate LED will flash. If you wish to test the
external sounders and strobe pressing 9 will toggle the external sounders
and strobe
On and Off.
6) To escape from the Test option press Oand the display will show as in Fig 6.
7) If you wish to return to DAY mode Press Oagain.
Page 7

GARDTEC 350
LOG
users Manual
The Gardtec 350 has a 50 event Log that records system events in the order that they.
occur.
To view the Log proceed as follows:-
1) With the Control panel in the DAY mode (Unset) enter-
the Master code. The
exit tone will sound.
2)
3)
Before the exit time expires Press NO. The exit tone will silence and the
!Piemove LED will flash.
Press NO Twice
and the log LED will flash as shown in Fig 7.
Fig 7.
POWER Cl
DAYCl
4) Press YES to use the log option. The display shown is the last event. To
view the previous event press NO, to move to the next event press YES.
5)
To escape out of the logi option press Oand the display will show as in Fig 7.
6) If you wish to return to DAY mode press Oagain.
Whilst in the logi mode the LEDs may display the following:-
AII LEDs on indicates an alarm, press NO to view the cause.
DAY LED with Z1,
Z2 or Z3 LEDs indicate unset by user 1, 2 or 3
Rapid flashing DAY LED. System was Set. Slow flashing DAY LED System was Part
set
If all the LEDs are flashing this indicates an alarm occurred. Pressing
NO to move to
the previous event will show the cause of alarm
If th.e
zone LED(s) are illuminated without the alarm indication the zone was removed.
Page 8
GARDTEC 350
CHIME
users Manua 1
The Chime function may be turned On or Off by the Master user. Before Chime can be
turned on
the Chime zones should have been programmed by your engineer.
To turn the Chime On or Off proceed
as follows:-
1)
2)
3)
With the Control panel in
the DAY mode (Unset) enter the Master code. The
exit tone will sound.
Before the exit time expires Press NO. The exit tone will silence and the
!Piemove LED
will flash.
Press
NO Three times and the !Clhnme LED will flash as shown in Fig 8.
Fig 8.
POWER Cl
DAV CJ
Z1 Cl ~=·"'-"",,e,•""""
Z2 □ .
Z3 CJ IIO.
z4 " ";'
~ .r.
ZS c:J ,l:J:r-.
TAMPERci
4) Press YES to change the status of the !Crhlnme . The Display will show as Fig 9.
5)
Fig 9.
POWER CJ
DAYCl
Z1 Cl fflfliWVa
Z2 c::;J
Z3CI
Z4- W __ _
ZS CJ f.l'.illtfil'.imJ
TAMPER}1, (!
Press YES again to escape from the Crhlnme option.
6) To escape back to DAY mode press 0
Page 9

GARDTEC 350
USER CODES
Users Manual
When programming User Codes you should note the following:-
a) User 1 is always the Master Code. This level of cod.e allows you
to perform all
User functions (including resetting after an alarm) and all User Programming
functions. The Master Code may be changed by the Master User but it
may
not be deleted.
b) User 2 is always a User level. This level of code will allow you to Set, Part
Set and Unset the system. If you wish to delete the code enter 0000 when
asked to enter the code during programming.
c) User 3 is a Set
only level. This level will allow you to Set and Part Set the
system only. If you wish to delete this code enter 0000 when asked to enter
the code during programming.
To program the user codes proceed as follows:-
1)
2)
3)
With the Control panel in the DAY mode (Unset) enter the Master code. The
exit tone will sound.
Before the exit time expires Press NO. The exit tone will silence and the
!Plsmovs LED will flash.
Press NO Four times and the
Program LED will flash as Fig 10.
Fig 10.
•ll:ll
POWER CJ
DAY CJ
Page 10
GARDTEC 350
users iv1anua1
4)
5)
6)
7)
8)
Press YES to use the
!Pmgiram (Codie) option. The display will show as
Fig
11
Fig 11.
POWER CJ
Enter the User number you wish to program followed by YES from:-
1 =Master Code
2 = User Code
3 =Set Only Code
A comfort tone is generated if all is okay
Enter a new four digit code followed by YES (entering 0000 will delete the
present code, however
the Master code may only be changed and not
deleted). A comfort tone will be generated if all is okay.
Enter the same four digit code again to confirm followed by YES. {If a mistake
has beenmade and no comfort tone is generated or if the two codes do not
match the code will not be updated.
If you wish to program
other user codes repeat from step 4
To escape back to DAY mode press 0.
Note: Any of the digits 0-9 may be used any number of times in a user code.
Page 11

<iiARDTEC 350
users Manual
CARE AND SERVICE OF YOUR SYSTEM
User care of the system consists of occasionally wiping the control panel. Under no
circumstances should detergents or abrasives be used.
Opening the control panel or detectors will generate a tamper alarm and service
should be carried out by a qualified alarm engineer. It may be a condition of your insur-
ance policy that your alarm system is serviced
on a regular basis. Please contact your
installation company for details of service.
TERMINOLOGY
User
Full Set
Part Set
Unsetting
Zone
Resetting
DAV Mode
Chime
Remo~e
Log
LED
P.A
Tamper
A person who will use the control panel (e.g turn the alarm on or off).
To turn all protected areas on ie to arm all areas.
To set the system leaving a group or groups of areas unprotected.
To turn off (disarm) the system.
An area protected by the alarm system.
To restore back to normal DAY mode display usually after
an alarm
condition.
The alarm system
is unset.
A chime zone that is activated will give an audible tone from the
control panel. It should be noted that chime zones need to be
programmed by the engineer. The chime function may be turned on
and off by the Master user.
The remove function allows the system to be set with individual
zones removed. This function is
in addition to any Part Sets.
A history of events.
Light Emitting Diode (indicating lamp).
P.A (Personal Attack) is active 24 hours irrespective of the control
panel being set or unset. It may be activated by pressing keys 1 and
3 together on the control panel or activating a P.A button that has
been allocated to a zone by the engineer.
Monitored 24 hours a day will give an audible warning if activated.
Page 12
GARDTEC 350
users Manua1
INSTALLATION DETAILS
Company Name:- Company Address:-
Company Tel No:-
Service Tel No:-
First Service Due Date:-
SERVICE RECORD
Service No Due Date Actual Date Engineers Sig
1
2
3
4
5
6
7
8
9
10
11
12
13
Page 13