Garmin Fishfinder 140 User manual

MANUAL FOR DIGITAL ALARM CLOCK WITH
PROJECTION MODEL

SYMBOLS
This symbol is followed by an important notice, this symbol is followed by a note
For safe use, always follow the instructions in this documentation
PACKAGE CONTENTS
Digital alarm clock
AC adaptor
Manual
DESCRIPTION
- LCD display
- permanent display backlight option when on battery power, 3 brightness levels and option to turn backlight
off
- option to turn on display backlight for 8 seconds when on battery power
- measurement of indoor temperature (°C, or °F) and relative humidity
- time and date controlled by DCF-77 radio signal with manual setting option
- 12- or 24-hour time display format
- timezone settable from -12 to +12 hours
- 2 alarm clocks
- repeated 5-minute snooze function
- projection of time and indoor temperature
- the projected image can be rotated by 180°
- option to turn off the projection
- USB port for charging mobile devices
- main unit powered by the AC adaptor or batteries
Description
Front and side view
2

1) Date / wake-up time 1
2) Time
3) DCF-77 signal reception icon
4) Projection
5) Projector tube
6) Temperature, relative humidity / wake-up
time 2
7) TIME button
8) ALARM button
9) Day name abbreviation
10) Button +
11) Button -
12) Alarm 1 switch
13) Alarm 2 switch
14) Power USB port
Top and rear view
15) Touch button
16) Projector
17) Projection ON OFF button
18) Button
19) Button WAVE
20) Battery compartment cover
21) Power supply socket
COMMISSIONING
The alarm clock can be powered by the AC adaptor or batteries. Use only the delivered AC adaptor.
Battery installation
1) Remove the battery compartment cover on the rear side of the alarm clock.
2) Insert 2 pcs AAA batteries (micro) – observe the correct battery polarity.
3) Close the battery compartment.
Connecting the AC adaptor
1) Connect the AC adaptor plug into the socket on the rear side of the main unit.
2) Connect the other side of the AC adaptor to a mains socket.
Time controlled by the DCF-77 radio signal
The weather station is equipped with the DCF-77 time/date control signal receiver, the signal is
broadcasted by a transmitter from Frankfurt am Main, Germany, with a range of about 1500 km. When
outside this range, the time and date can be adjusted manually. The time and date are adjusted every day.
After the power supply is connected, the display shows all segments for 3 seconds and a beep sounds.
Then the reception for the DCF-77 radio signal for adjusting the time and date commences, which is
indicated by a flashing icon on the display. This process may take several minutes. The display
3

4
backlight will be off for the duration of the DCF-77 signal reception, and the alarm clock functionality will be
also limited. Only the pushbutton and the WAVE button on the rear side of the clock will
function.
As soon as the signal is received successfully, the display shows the current time, date and signal reception
icon The weather station will automatically receive the DCF-77 signal to adjust the time every day at
1:00. If reception is unsuccessful (the icon will not appear on the display), reception will be attempted
again in another hour, five times in total. The received time is compared with the time on the main unit and
adjusted if necessary. For better signal reception, place the main unit near a window. As soon as the
DCF-77 signal is received successfully, the icon will be displayed.
Note:
The received DCF-77 time adjustment signal strength may be affected by the geographical location or the
premises where the weather station is located.
For better reception, the main unit should be placed on a flat non-metallic surface, near a window on the
upper floor of your house away from electrical appliances such as a TV, computer, etc.
Manual reception of the DCF-77 signal
To start the DCF-77 signal manually, press and hold the WAVE button on the rear side of the clock
for 2 seconds. To terminate the DCF-77 signal reception, press the WAVE button.
Manual setting of time and date
If the DCF-77 signal reception is not successful and the time and date are not adjusted, the adjustment can
be made manually.
To enter the setting mode, press and hold the TIME button for 2 seconds. For setting, use the +, or –
buttons. Confirm the setting by a single push of the TIME button, this will move to the next setting.
Setting order:
Set time format 12 or 24 hours (12H / 24H) set timezone from -12 to +12 hours (for the Czech and
Slovak republic leave 00) set current hour set current minute set date display order day-month
(D-M), or month-day(M-D) set current year set current month set current day set the
language of the day name abbreviation
The setting mode is terminated by the last confirmation.
Note: If no button is pressed for 20 seconds, the setting mode will be terminated.
Day name abbreviations
Monday Tuesday Wednesday Thursday Friday Saturday Sunday
GE
-
German
MO
DI
MI
DO
FR
SA
SO
EN - English MO TU WE TH FR SA SU
FR
-
French
LU
MA
ME
JE
VE
SA
DI
IT
-
Italian
LU
MA
ME
GI
VE
SA
DO
SP
-
Spanish
LU
MA
MI
JU
VI
SA
DO
DU
-
Dutch
MA
DI
WO
DO
VR
ZA
ZO
DA - Danish MA TI ON TO FR LO SO

5
SETTING WAKE-UP TIME AND SNOOZE FUNCTION
Push the ALARM button once to display wake-up time of alarm 1 and alarm 2
1) Press the ALARM button and hold for 2 seconds. The wake-up times of alarm 1
and 2 will be displayed and the alarm 1 wake-up hour will flash. Use the +, or – buttons to set
the required wake-up hour and confirm with the ALARM button.
2) The wake-up minute will flash. Use the +, or – buttons to set the required wake-up minute and
confirm with the ALARM button.
3) The wake-up hour of the alarm 2 will flash. Use the +, or – buttons to set the required wake-up
hour and confirm with the ALARM button.
4) The wake-up minute will flash. Use the +, or – buttons to set the required wake-up minute.
Confirm the setting and finish the setting by pushing the ALARM button.
Note: If no button is pressed for 20 seconds, the setting mode will be terminated.
Activating and deactivating the alarm clock
To activate or deactivate alarm 1 slide the switch ON/OFF on the side to the ON position (activated) or
OFF (deactivated). Alarm 1 is activated if the icon is displayed.
To activate or deactivate alarm 2 slide the switch ON/OFF on the rear to the ON position (activated) or
OFF (deactivated). Alarm 2 is activated if the icon is displayed.
Snooze function
To deactivate the snooze function, push any button except .
To activate the SNOOZE function, push the button while the alarm is active, icons , or
will flash and the alarm will be postponed for 5 minutes, and then reactivated. This process may be
repeated.
If no button is pressed, the alarm with deactivate automatically after 2 minutes. The wake-up alarm will be
repeated after 24 hours at the set time.
PROJECTION
The weather station has a projection of time and indoor temperature. The ideal distance of the projection
surface is 1.5 to 3 meters in an unlit room.
The projector tube can be tilted by 90° back and 90° forward.
When the main unit is powered by batteries only, the projection and the backlight will be on for 8 seconds
using the touch button on the top of the main unit. When powered with the AC adaptor the
projection will be permanent. The projection can be activated (ON) or deactivated (OUT) using the
Projection switch on the rear of the main unit.
To rotate the projected image by 180°, push the button
Projection is off while receiving the DCF-77 signal for time and date adjustment.

6
DISPLAY BACKLIGHT
When the alarm clock is powered by batteries only, the projection and the backlight will be on for 8 seconds
using the touch button on the top of the main unit. When powered by the AC adaptor, the backlight
can be on permanently or turned off. Push the button repeatedly to select the backlight brightness
in 3 levels, or to turn the display backlight off.
The display backlight is off while receiving the DCF-77 signal for time and date adjustment.
CHARGING MOBILE DEVICES
The alarm clock has USB port for charging mobile devices. You can only charge your mobile device when
the alarm clock is powered by the AC adaptor.
The charging commences automatically when the mobile device is connected. Monitor the charging
process and disconnect the cable from the USB port when the mobile device is charged.
Notice: The USB port can only supply a charging current of 1,000 mA.
SAFETY PRECAUTIONS
• Do not expose the device to excessive force, shocks, dust, temperature and humidity
• Do not cover the ventilation holes with any objects like newspapers, curtains, etc.
• Never immerse the device in water. If you spill liquid on it, dry it immediately with a soft, lint-free cloth
• Do not clean the device with abrasive or corrosive substances
• Do not handle the internal components of the device, as this will void your warranty
• Use only fresh batteries. Never mix fresh and old batteries
• Do not recharge the batteries. Place the station and its parts outside the reach of children
• Do not throw old batteries to unsorted municipal waste, but use the designated areas
• Dispose of this product in accordance with applicable regulations
• Use only accessories specified by the manufacturer
• Do not interfere with the internal circuits of the device, as this may void the warranty
• The technical specifications are subject to change without notice
TECHNICAL PARAMETERS
Power supply: AC adaptor 100-240 V, 50/60Hz, 0,3 A / 5V, 1,2 A
2 pcs of 1,5 V AAA batteries (micro)
Temperature measurement range: -9°C to +50°C
Accuracy of measurement: +/- 1°C
Resolution: 1°C
Rel. humidity measurement range: 20% to 95%
Accuracy of measurement: +/- 5%
Resolution: 1%
Dimensions 136 x 84 x 32 mm
GARNI technology a.s. hereby declares that the Digital alarm clock model GARNI 140 meets all basic
requirements of the applicable EU Directives. The full EU Declaration of Conformity is available on the following
website: www.garni-meteo.cz
The manual was prepared for GARNI technology a.s. by Roman Gajda.
Reproduction of this manual or its parts is prohibited without the author's consent
Version 03G20