Garmin G3000 User manual

REFERENCE ONLY
1
Version 1.0 REFERENCE ONLY
Swapping GSA80 Roll & GSA80 Yaw Servo on Citation CJ3+
Garmin G3000 Software Version 10
Caution: Before starting the software or configuration loading process, certain
items may be required to be recorded first, to prevent loss of
information or settings. See Section 1 for details.
Caution: Make certain that all SD cards are available before starting. These are
usually located in a blue pouch onboard the aircraft (usually in AFM).
Caution: Follow all steps in a given section for specific loadings. Failure to do so
will result in probable rework.
Caution: Ensure that power is available through a GPU so that power is not
interrupted during the loading process.
Note: This document is to supplement, not replace, the Cessna Citation CJ3+
MM, and Garmin G3000 LMM.
Note: Reference latest revision of the Garmin G3000 LMM 190-01785-00.
Table of Contents
Introduction G3000 System Familiarization
Section 1 Determining Options Installed
Section 2 Software and Configuration Loading
Section 3 Final Verification / Return to Service
Section 4 FLEET ID / CRC Numbers
Section 5 Troubleshooting

REFERENCE ONLY
2
Version 1.0 REFERENCE ONLY
Introduction G3000 System Familiarization
When in configuration mode, select GDU controls on left side of GTC 1. Ensure that PFD 1 is
selected on the screen. The dual concentric knobs on the lower right bezel will be utilized, and
throughout this document will be referred to as the FMS small and large knob. The Enter
button will be in the lower right part of the screen.
As an alternative, you can use the dual concentric knobs (labeled PFD) and Enter button on the
GCU-275 controller mounted above PFD 1.

REFERENCE ONLY
3
Version 1.0 REFERENCE ONLY
Section 1 Determining Options Installed
Determine Options Installed
Note: This is with the G3000 powered up in normal mode.
•Synthetic Vision
oOn the PFD, select PFD Settings, then select Attitude Overlays. If Synthetic Terrain
button is displayed, mark YES.
•Checklist
oFrom the Home screen of either GTC 570, look for Checklist button to be
displayed. It may be grayed out, but if the button is present, mark YES.
YES
NO
YES
NO

REFERENCE ONLY
4
Version 1.0 REFERENCE ONLY
•CPDLC
oMark YES if the CPDLC button is available on the home screen of either GTC.
•Single GSR56 (Iridium Phone)
oOn either GTC 570, select the SERVICES / TELEPHONE button, then select
Telephone. Mark YES if a single Iridium transceiver is displayed on the left side.
•Dual GSR56 (Iridium Phone)
oOn either GTC 570, select the SERVICES / TELEPHONE button, then select
Telephone. Mark Yes if a double Iridium transceiver is displayed on the left & right
side.
•ACARS
oFrom the Home screen of either GTC 570, look for a Services button. If it is
located, select it and look for a button marked ACARS. If it is present, mark YES.
oThe service provider will be determined later on page 11.
YES
NO
YES
NO
YES
NO
YES
NO

REFERENCE ONLY
5
Version 1.0 REFERENCE ONLY
•GDL69 (XM Receiver)
oFrom the Home screen of either GTC 570, touch the Weather button. Then touch
Weather Selection. If Sirius XM Settings is displayed, mark YES.
•GSR56 Weather
oFrom the Home screen of either GTC 570, touch the Weather button. Then touch
Weather Selection. If CONNEXT WEATHER is displayed, mark YES.
•Stormscope (Lightning Detect)
oFrom the Home screen of either GTC 570, touch the Weather button. Then touch
Weather Selection. If Stormscope is displayed, mark YES.
•Doppler & Turbulence (Includes Ground Clutter Suppression)
oFrom the Home screen of either GTC 570, select the Weather button. Select
Weather Selection button. Select the WEATHER RADAR SETTINGS button & if the
Turbulence Detection & GND Clutter Suppression buttons are visible, mark YES.
YES
NO
YES
NO
YES
NO
YES
NO

REFERENCE ONLY
6
Version 1.0 REFERENCE ONLY
•Ground Clutter Suppression (Stand Alone Option Without Doppler & Turbulence)
oFrom the Home screen of either GTC 570, select the Weather button. Select
Weather Selection button. Select the WEATHER RADAR SETTINGS button & the
GND Clutter Suppression button will be visible, without the Turbulence
Detection button. Do not select YES if Doppler & Turbulence is selected YES
above.
•Cabin Briefing
oFrom the Home screen of either GTC 570, select AIRCRAFT SYSTEMS. If the Cabin
Briefing button is displayed, mark YES.
•SurfaceWatch
oFrom the Home screen of either GTC 570, select Utilities. Select Setup & then
Avionics Settings. Then select the Alerts tab. If the SurfaceWatch Inhibit button is
visible, mark YES. Note the Inhibit box will not be illuminated (resets at power up).
YES
NO
YES
NO
YES
NO

REFERENCE ONLY
7
Version 1.0 REFERENCE ONLY
•Becker ADF
oIf ADF is seen on the AUDIO & RADIO screen of either GTC 570, mark YES.
•GDR66 (VHF Datalink (Datalink/COMM 3))
oIf GDR or Datalink are seen on the AUDIO & RADIO screen of either GTC 570, mark
YES. They should appear as one of the 2 images below and labeled as COM3 with
frequencies, or Datalink showing on the right side.
or
•HF9000
oIf HF9000 is seen on the AUDIO & RADIO screen of either GTC 570, mark YES.
•DME 2
oIf DME2 is seen on the AUDIO & RADIO screen of either GTC 570, mark YES.
YES
NO
YES
NO
YES
NO
YES
NO

REFERENCE ONLY
8
Version 1.0 REFERENCE ONLY
•TAWS Class A
oFrom the Home screen of either GTC 570, select the TAWS button. Then select
TAWS Selection button. If there are 6 buttons displayed on the page, then TAWS
A is loaded, and mark YES. Otherwise TAWS B is loaded as default. Note: First
image is TAWS B, and second image is TAWS A.
•EROS Oxygen Mask
oLook at the crew mask and determine if EROS brand. If the mask is an EROS, mark
YES. Note: The option changes the gains for the microphone if EROS is installed.
Placing System Into Configuration Mode
Note: Anytime that software or configurations are being loaded, all three displays, and both
touch controllers must be in configuration mode.
•When GCU 1 is replaced, then software and configuration loading is required.
1) Pull the following circuit breakers:
L PFD
MFD
R PFD
L Touch Control
R Touch Control
2) Insert the 010-01293-10 software loader card into the upper slot of PFD 1.
3) Turn on aircraft power.
YES
NO
YES
NO

REFERENCE ONLY
9
Version 1.0 REFERENCE ONLY
4) Press and hold the right knob on the left GTC and push the L Touch Control circuit
breaker in.
Let go when you see initializing.
5) Press and hold the right knob on the right GTC and push the R Touch Control
circuit breaker in.
Let go when you see initializing.
6) Press and hold the #12 softkey on the #2 PFD and push the R PFD circuit breaker
in.
Let go when you see initializing.
PFD 2 should come up in configuration mode.
•SYSTEM STATUS should show at the top of the screen.
7) Press and hold the #12 softkey on the MFD and push the MFD circuit breaker in.
Let go when you see initializing.
MFD should come up in configuration mode.
•SYSTEM STATUS should show at the top of the screen.
8) Press and hold the #12 softkey on the #1 PFD and turn on power.
Let go when you see initializing.
9) Press the NO softkey at “DO YOU WANT TO UPDATE SYSTEM FILES?” prompt.
10) Press the NO softkey at “DO YOU WANT TO UPDATE THE CUSTOM GRAPHICS
FILES (EG, SPLASH SCREEN)?” if it appears.
11) PFD 1 should come up in configuration mode.
SYSTEM UPLOAD should show at the top of the screen.

REFERENCE ONLY
10
Version 1.0 REFERENCE ONLY
Determine Options Installed (Options That Can Only Be Seen In Configuration Mode)
Note: This is with the G3000 still powered up in configuration mode.
•ACARS Service Provider (Only if ACARS was determined to be an option per page 3)
oRotate small FMS knob until on AIRCRAFT CONFIGURATION page.
oOn the IATA Airline Designator line, look for a 2 letter code and check appropriate
box in the table below.
XA designates ARINC Direct
GS designates Honeywell GDC
UV designates Universal Weather
ARINC Direct
Honeywell GDC
Universal Weather
•TAWS A Voice Callouts (100-400 FT) (In Addition to Standard 500 FT Callout) (Only if
TAWS A option is installed)
oThe system should still be in configuration mode from before.
oRotate the large FMS knob until on the GDU tab (near the left side of the choices).
oRotate the small FMS knob to the right until on TAWS Configuration.
oSelect VCO (voice call out) at the bottom of the display.
oVCO 500 (500 FT) is highlighted, and will always show TRUE below it, as this is
standard. Do not mark YES for this part.
oRotate the small FMS knob to the right one turn to change to VCO 400 (400 FT).
oIf it is FALSE below the VCO 400 under the Enabled line, then the TAWS A
Callout feature is not turned on (Second Image). Select NO.
oIf it is TRUE below the VCO 400 under the Enabled line, then the TAWS A Callout
feature is turned on (Third Image). Select YES.
Standard 500 FT VCO
YES
NO