IHP Envy AKC-CLS-DLSCNV User manual

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
1
P/N 900005-05
Rev. NC 10/2014
INSTALLATION INSTRUCTIONS FOR ANDIRON KITS
FOR USE WITH ENVY DIRECT-VENT GAS FIREPLACES
FIREPLACE MODELS ENVY35T(E/Y)N, ENVY40T(E/Y)N, AND ENVY45T(E/Y)N,
DECORATIVE ANDIRON KIT
ENVY™ TRADITIONAL SERIES
HEARTH PRODUCTS
KITS AND ACCESSORIES
Envy™ Series Andiron Kits
Cat. No. Model Description
H8723 AKC-CLS-DLSCNV Andiron Kit, Classic
KIT CONTENTS
2 ea. Andirons
4 ea. Thumbscrews (2 attached to each andiron)
TOOLS NEEDED
Safety Glasses
Protective Work Gloves
Figure 1
GENERAL INFORMATION
This document contains installation instructions for the andiron kit used
with ENVY direct vent gas fireplaces. The decorative andiron kit is offered
as an enhancement to the firebox appearance.
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION INSTRUC-
TIONS AND CARE AND OPERATION MANUALS PROVIDED WITH THE
APPLIANCE APPLY TO THESE INSTRUCTIONS.
TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
FIREBOX ACCESS
Step 1. Use the fireplace remote control to ensure the fireplace is OFF.
Step 2. Remove the top louver.
Step 3. Remove the left and right side finish trim gap fillers.
Step 4. Remove the surround trim assembly by detaching it at the top
of the fireplace and lifting it 1” to disengage the side tabs, then
pulling it away from the fireplace exposing the front glass door.
Step 5. Locate the four (4) spring-loaded latches (Figure 2); two above
and two below the enclosure. Release the lower latches, by
pulling each handle out and down to unhook it from the glass
door. Lightly press against the door, to hold it in position, while
releasing the two upper latches. Carefully grip the glass door at
both the top and bottom, and remove from the fireplace. Retain
the door in a secure location for later reinstallation.
Upper Glass Enclosure Latches
Lower Glass Enclosure Latches
Figure 2 - Upper And Lower Glass Door Latches
NOTE: It is not necessary to handle the log set when installing the
andirons.
Lower Glass Enclosure Latches
Upper Glass Enclosure Latches
P900005-05
fire-parts.com

2
Printed in U.S.A. © 2014 Innnovative Hearth Products
P/N 900005-05 Rev. NC 10/2014
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
IHP reserves the right to make changes at any time, without notice,
in design, materials, specifications, and prices, and to discontinue
colors, styles, and products. Consult your local distributor for
fireplace code information.
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
IHP.us.com
INSTALLATION INSTRUCTIONS
The mounting holes for the andirons are located along the
front of the firebox.
NOTE: When installing the andirons for the first time, use a
screwdriver to bend down the metal tabs covering the mounting
holes.
Step 1. Insert one of the andirons into the left mounting holes in the
firebox base (Figure 3).
Step 2. Insert the second andiron down into the right mounting holes
in the firebox base (Figure 3).
NOTE: The andirons are loose in their mounting holes to allow for
metal expansion when the fireplace is in operation.
Figure 3 - Classic Andiron Installation
FIREPLACE REASSEMBLY
Step 1. Carefully position the glass door in front of the firebox and hook
the two upper spring-loaded latches over the door frame.
Step 2. Hook the two lower spring-loaded latches over the door frame.
Step 3. Use an ammonia-free glass cleaner and a soft, non-abrasive cloth
to remove fingerprints and smudges from the glass door.
Step 4. Locate the surround trim assembly mounting slots along the
left and right edges of the firebox.
Step 5. Align the surround trim assembly with the mounting slots and
press in and down to lower it into position. Reinstall the left and
right side finish trim gap fillers.
Step 6. Use an ammonia-free glass cleaner and a soft, non-abrasive
cloth to remove fingerprints and smudges from the surround
trim assembly.
P900005-05
fire-parts.com