GB BGB300 User manual

BGB300 GAME RIDER
OWNER’S MANUAL
*This item is for consumer use only and it is not meant for commercial use.

This page intentionally left blank

General Information
BGB 300 Page 1
Warranty
Body Flex Sports warrants your product for
a period of 1 year for the frame and 90 days
on all parts if the item is used for the intended
purpose, properly maintained and not used
commercially. Any alterations or incorrect
assembly of the product will void this warranty.
Proof of purchase must be presented for any
warranty validation (no exceptions). This
warranty applies to the original purchaser only
and is not transferable.
This warranty does not cover abuse or defects
caused during use, storage or assembly.
During the warranty period, Body Flex Sports
reserves the right to:
a). provide replacement parts to the
purchaser in an effort to repair the item.
b). repair the product returned to our
warehouse (at the purchaser’s cost).
c). replace the product if neither of the two
previously mentioned actions effect repair.
This warranty does not cover normal wear and
tear on upholstery.
Questions
If you have any questions concerning the
assembly of your item or if any parts are
missing, please DO NOT RETURN THE
ITEM TO THE STORE OR CONTACT THE
RETAILER. Our dedicated customer service
staff can help you with any questions you may
have regarding the assembly of this unit and
can also mail you replacement parts.
Customer Support
Customer Support is open 9:00 a.m. to 5:00
p.m. (Pacific Time) Monday through Friday.
Please contact us by any of the following
means.
Body Flex Sports, Inc.
21717 Ferrero Parkway, Walnut, CA 91789
Telephone: (888) 266 - 6789
Fax: (909) 598 - 6707
Email: info@bodyflexsports.com
Safety
Before you undertake any exercise program,
please be sure to consult with your doctor.
Frequent strenuous exercise should be
approved by your doctor and proper use
of your product is essential. Please read
this manual carefully before commencing
the assembly of your product or starting to
exercise.
• Please keep all children away from this item
when in use. Do not allow children to climb or
play on them when they are not in use.
• Supervise teenagers while they use this unit.
• For your own safety, always ensure that there
is at least 3 feet of free space in all directions
around your product while you are exercising.
• Regularly check to see that all nuts, bolts and
fittings are securely tightened. Periodically
check all moving parts for obvious signs of
wear or damage.
• Clean only with a damp cloth, do not use
solvent cleaners. If you are in any doubt, do
not use your product; contact CUSTOMER
SUPPORT.
• Before use, always ensure that your product
is positioned on a solid, flat surface. If
necessary, use a rubber mat underneath to
reduce the possibility of slipping.
• Always wear appropriate clothing and
footwear such as training shoes when
exercising. Do not wear loose clothing that
could become caught in moving parts during
exercise.
• Do not use this unit if it is not functioning
properly or if it is not fully assembled.
• Do not use this unit for commercial purposes.
Storage and Use
Your product is intended for use in clean
dry conditions. You should avoid storage in
excessively cold or damp places as this may
lead to corrosion and other related problems.
Weight Limit
Your product is suitable for users weighing:
250 pounds or less.
• Before use, you must read and understand all
instructions & warnings stated in this Owner’s
Manual as well as posted on the equipment.
• It is the facility owner’s responsibility to properly
instruct users on the proper operation of the
equipment and to warn them of the potential
hazards.
• If at any time during exercise you feel faint, dizzy
or experience pain, stop and consult your
physician.
Assembling Tools
- Ruler with both metric and English measurements
- 2 x Adjustable Wrenches
- 1 x Philips (”Crosshead”) Screw Driver

BGB 300 Page 2
Hardware List
The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these
items. Please note some of this hardware is already pre-assembled on the machine. Do not be alarmed if you
see parts on this page that are not included in your hardware packet
Bolt
#14 Carriage Bolt (M8x90 mm)
[2 Pieces]
#22 Screw (M8x25 mm)
[2 Pieces]
#23 Screw (M8x16 mm)
[4 Pieces]
#25 Screw (M5x10 mm)
[4 Pieces]
Washer
#26 Screw (M5x16 mm)
[3 Pieces]
#27 Spring Washer (M8)
[2 Pieces]
#28 Arc Washer (M8)
[8 Pieces]
#29 Washer (M10)
[1 Piece]
#30 Washer (M5)
[4 Pieces] #32 Washer (M8, OD16)
[3 Pieces] Pre-assembled
Nut
#15 Lock Nut (M8)
[4 Pieces]
#33 Nut (M8)
[3 Pieces] Pre-assembled
Knob
#18 Knob (M8x15 mm)
[1 Piece]
#17 Spring Knob
(M16x27 mm) [1 Piece]
#16 Knob (M10)
[1 Piece]
Tool
#13 Carriage Bolt (M8x73 mm)
[2 Pieces]

Page 3BGB 300
# Description # Description
01 Main Frame
33
02 Front Stabilizer
34
03 Rear Stabilizer
35
04 Center Post
05 Handle Bar
36
06 Monitor Support Bracket
37
07 Seat Post
38
08 Horizontal Seat Bar
40 Square End Cap (38 mm)
09 Seat
41 Square End Cap (20 mm)
10L Pedal (Left)
42 Round End Cap
10R Pedal (Right)
43 Monitor
11 Poster Support
43a Left Handle Pulse Wire (Upper)
12 Poster Board
43b Right Handle Pulse Wire (Upper)
13 Carriage Bolt (M8x73 mm)
43c Main Sensor Wire (Upper)
14 Carriage Bolt (M8x90 mm)
43d Handle Sensor Wire (Upper)
15 Lock Nut (M8)
44 Main Sensor Wire (Lower)
16 Knob (M10)
45a/b Main Sensor Wire (Middle)
17 Spring Knob (M16x27 mm)
18 Knob (M8x15 mm)
47 Left Handle Pulse Wire (Lower)
19 Lock Pin
48 Right Handle Pulse Wire (Lower)
20 Screw (M5)
49L Left Handle Bar Button
21 Screw (ST4)
49R Right Handle Bar Button
22 Screw (M8x25 mm)
50a AC Adapter for Wireless Box (DC 6V, 1000mA)
23 Screw (M8x16 mm)
50b AC Adapter for Bike (DC 8V,1000mA)
24 Screw (ST3)
51 Wireless Box
25 Screw (M5x10 mm)
52a AV Cable (Upper)
26 Screw (M5x16 mm)
52b Audio Cable (Lower)-White
27 Spring Washer (M8)
52c Video Cable (Lower)-Yellow
28 Arc Washer (M8)
53a USB Cable (Upper)
29 Washer (M10)
53b USB Cable (Lower)
30 Washer (M5)
54 Pulse Sensor
31 Washer (M6)
55 Resistance Band
32 Washer (M8,OD16)
56L Crank (Left)
56R Crank (Right)
Shroud
End Cap for Front Stabilizer
End Cap for Rear Stabilizer
Bushing
39 Rubber Ring (φ50 mm)
Nut (M8)
Center Post Cover
46 Handle Sensor Wire (Lower)
57
58
Handle Bar Cover (Lower)
Handle Bar Cover (Upper)
59
60
Rubber Ring (φ60 mm)
U Bracket
Parts Listing
The following parts list describes all of the parts illustrated on the
exploded diagram on the following page. Please note, most of
these parts are already pre-assembled on your unit.

Page 4
Exploded Diagram
The following diagram is provided to help you familiarize yourself with the parts and
hardware that will be used during the assembly process. Please note that not all of the
parts and hardware you see here will be used while you are assembling the machine
because some of these items are already pre-installed. Please continue to the next
page to begin the assembly process and use this page only as a reference guide for
parts and hardware.
BGB 300

BGB 300 Page 5
Make sure the wire is hanging out before
proceeding to the next step. If it has fallen
inside the tube, use a bent wire to “fish” them out.
Nut
#15 Lock Nut (M8)
[4 Pieces]
Tool
A s s e m b l y S t e p 1
Hardware & Tool Required
Bolt
#13 Carriage Bolt (M8x73 mm)
[2 Pieces]
Washer
#28 Arc Washer (M8)
[4 Pieces]
#32 Washer (M8, OD16)
[3 Pieces]
#33 Nut (M8)
[3 Pieces]
#14 Carriage Bolt (M8x90 mm)
[2 Pieces]
Front & Rear Stabilizer Assembly
With the help of an assistant, attach the Front Stabilizer
(#02) to bracket at the front of Main Frame (#01). Insert two
Carriage Bolts (#13) through the Front Stabilizer (#02)
followed by the front Main Frame (#01). Secure them
together using two Arc Washers (#28) and two Lock Nuts
(#15). Now attach the Rear Stabilizer (#03) to the bracket
at rear of Main Frame (#01). Insert two Carriage Bolts (#14)
through the Rear Stabilizer (#03) followed by the rear
Main Frame (#01). Secure them together using two Arc
Washers (#28) and two Lock Nuts (#15).
NOTE: The Front Stabilizer (#02) has wheels on the end
caps that spin for ease of relocating and transporting the unit.
The Rear Stabilizer (#03) has height adjustable end caps
for leveling of the unit .
A s s e m b l y S t e p 2
Seat Assembly
Remove the three Washers (#32) and three Nuts (#33)
that are pre-installed on the Seat (#09) as illustrated and
set them aside. Align the holes of the Seat (#09) to the
Horizontal Seat Bar (#08) as shown in the diagram.
Next, secure them together using three Washers (#32)
and three Nuts (#33) that were previously removed.
Assembly Instructions

BGB 300
Spring Knob Operation
Turn knob counter-clockwise
three times.
Pull knob outward and adjust
seat simultaneously
Push knob back inward until
it clicks and then tighten it by
turning clockwise.
NOTE:
If labels designating the Left/Right Pedal
are not present, please check pedals
closely for embossed “L”/ “R” letter marks.
These will be “L” / “R” letters that are
raised on the pedal material.
WARNING
Do not remove the Seat (#09) for any
reason after you have installed it.
Exercising on this unit without the Seat
(#09) can result in SERIOUS INJURY.
Ensure the seat is locked in place by
tightening the two knobs prior to use.
A
B
A s s e m b l y S t e p 3 Hardware & Tool Required
Seat Post Assembly
Pedal Assembly
Screw the Pedal [Left](#10L) to the Crank [Left] (#56L) by turning the
bolt head on the Pedal [Left](#10L) COUNTER-CLOCKWISE.
Screw the Pedal [Right](#10R) to the Crank [Right] (#56R) by turning
the bolt head on the Pedal [Right](#10R) CLOCKWISE.
A.) Attach the Horizontal Seat Bar (#08) onto the Seat Post (#07) by
inserting the bolt (on the bottom of the Horizontal Seat Bar (#08))
through the Seat Post (#07), secure them using a Washer (#29)
and a Knob (#16). This knob can be loosened to adjust the distance
of the seat from the handle bars. Make sure to tighten the knob after
making any adjustment,
but do not over tighten the knob.
B.) If the Seat Post (#07) is not already pre-assembled, please insert
the Seat Post (#07) into the mouth of the post that is protruding
from the Main Frame (#01). Please ensure that the hole on the Seat
Post (#07) is facing the right so it can be aligned with the corresponding
hole on the Main Frame (#01). Screw in the Spring Knob (#17)
through the Main Frame (#01) post and through any hole located on
the Seat Post (#07). Please refer to illustration. To use the
safety-featured Spring Knob (#17), use one hand to hold the Seat
(#09) to prevent sudden slipping and the other hand to loosen the
knob by turning it counter-clockwise three times as you pull it outward.
Adjust the seat height to your liking and then pop the knob back in.
Then, tighten the knob by turning it clockwise. Please do not
over-tighten.
Washer
#29 Washer (M10)
[1 Piece]
Knob
#17 Spring Knob
(M16x27 mm)
[1 Piece]
#16 Knob (M10)
[1 Piece]
Tool
Page 6
55
40 1 2 3 4
55
40 1 2 3 4
STEP3:
Assembly Instructions

BGB 300 Page 7
Bolt
#23 Screw (M8x16 mm)
[4 Pieces]
Washer
#28 Arc Washer (M8)
[4 Pieces]
Tool
A s s e m b l y S t e p 4 Hardware & Tool Required
55
40 1 2 3 4
55
40 1 2 3 4
STEP3:
Assembly Instructions
Post (#04) for now.
[Middle] (#45b) to the Main Sensor Wire [Lower] (#44).
Wire Connection
Then, connect the Main Sensor Wire
Center Post Assembly
Slide the Center Post (#04) onto the Main Frame (#01)
and secure it using a total of four Arc Washers (#28) and
four Screws (#23).
Center Post Cover
Then, slide down the Center Post Cover (#34) and Rubber
and twist/turn clockwise so it fits properly and
of the
snugly over the Main Frame (#01) . Please refer to positioning
Center Post Cover (#34) and Rubber Ring (#59)
in the diagram below.
Remove the Rubber Ring (#59) and Center Post Cover
(#34) from packaging and slide them onto and up the Center
Ring (#59)

Assembly Instructions
A s s e m b l y S t e p 5
Hardware & Tool Required
A s s e m b l y S t e p 6
Page 8
Pulse Handle Bar Assembly
Install the Handle Bar (#05) onto the inner side of the
Center Post (#04) using two Screws (#22) and two
Spring Washers (#27) as seen in diagram.
A.Place the Poster Support (#11) onto the corresponding
stem protruding from the Center Post (#04). Secure in
place using the Knob (#18) and tighten in place. You can
adjust the Poster Support (#11) location to your preference
by securing at the preferred angle.
B.Affix the Poster Board (#12) onto the plate of the Poster
Support (#11) using four Washers (#30) and four Screws
(#25).
C.The Poster Board (#12) and Poster Support (#11) are
intended to provide an easy-to-access guide to highlight
the key features and functions of the Game Rider. We
suggest placing the Poster Board (#12) at a 45 degree
angle to the user on either the right or left side.
Bolt
#22 Screw (M8x25 mm)
[2 Pieces]
#25 Screw (M5x10 mm)
[4 Pieces]
Washer
#27 Spring Washer (M8)
[2 Pieces]
#30 Washer (M5)
[4 Pieces]
Knob
#18 Knob (M8x15 mm)
[1 Piece]
Tool
A
B
C
BGB 300

Page 9
A s s e m b l y S t e p 7
Feed the Left Handle Pulse Wire (#47) and the Right Handle Pulse Wire (#48) through the side hole in
the neck of the Center Post (#04) and through the front hole of the Center Post (#04) as directed by the
arrow in diagram No. 1. You will need to connect these wires to the Monitor (#43) in later assembly step.
FRONT VIEW
BACK VIEW
Please also ensure that Handle Sensor Wire [Lower] (#46) and Main Sensor Wire [Middle] (#45) are fed
through the same hole as shown in diagram No. 2. Please refer to diagram No. 3 and No. 4 to confirm
proper assembly.
The Round End Cap (#42) is pre-installed to hold the Left & Right Handle Pulse Wires
(#47 & #48) as
seen in diagram No. 2. However, you may remove the Round End Cap (#42) so you can tuck in the wires
more if there is too much give, or you do not want the wire to hang out so much. If you remove the Round
End Cap (#42), please remember to snap it back in place to hold all the wires in place.
Assembly Instructions
BGB 300

Page 10
A s s e m b l y S t e p 8 Hardware & Tool Required
Bolt
#26 Screw (M5x16 mm)
[2 Pieces]
Tool
Align the holes of the Monitor Support Bracket
(#06) with the holes on the Center Post (#04) as
shown in the diagram. Please ensure that the
wires are free and clear from the bracket. Then,
secure the Monitor Support Bracket (#06) using
two Screws (#26 ).
#42 WASHER FOR M10 BOLT,T2.0 1PC
#42 WASHER FOR M10 BOLT,T2.0 1PC
#42 WASHER FOR M10 BOLT,T2.0 1PC
Assembly Instructions
Wires will fall freely in this step.
You do not and should not need to feed wires
through the Monitor Support Bracket (#26).
BGB 300

Page 11
Assembly Step 9
A.Please ensure that the cables connected to the Monitor (#43) are within the track of the backside so they do not get pinched
or damaged during this next process (please see diagram). Slide the track of the Monitor (#43) halfway onto the
Support Bracket (#06)
B.Now, connect the corresponding cables as shown in diagram No. 7:
- 43a to 47
- 43b to 48
- 43c to 45a
- 43d to 46
C.Then, carefully place and tuck all the connected cables into Hole B as shown in diagram No. 8.
Please note: 1.) there is room for you to tuck the cables upward and downward in the hollow area of the Center Post (#04)
2.) use care when tucking in cables to avoid injury to your fingers and hands
Monitor
, tuck the Wires (#43a/b/c/d) on the Monitor (#43) through Hole A (diagram No. 6), then slide the
Monitor (#43) onto the rest of the track until the monitor locks in place.
Please note: if you need to remove the Monitor (#43), press and hold down the tab on the back of the Monitor (#43) to unlock,
slide, then release the tab.
-Please connect designated wires to matching numbers (i.e. “1” to “1”; “2” to “2”).
Note: Wires do not require excessive force to connect; please use care when connecting.
Assembly Instructions
BGB 300

Page 12
A s s e m b l y S t e p 10
Hardware & Tool Required
Bolt
#26 Screw (M5x16 mm)
[1 Piece]
Tool
Place the Handle Bar Cover [Upper] (#58) over the inner side of the Center Post (#04). Please ensure
proper alignment as shown in the diagram. Next, connect the Handle Bar Cover [Lower] (#57) to the
Handle Bar Cover [Upper] (#58). The two covers should fit snugly in place. Secure with one Screw (#26)
through the top of the Handle Bar Cover [Upper] (#58).
The Handle Bar Cover [Lower] (#57) has a small indent for the Main Sensor Wire [Middle] (#45)
to tuck into so that it does not get pinched or damaged when connecting the covers. Please see
"VIEW FROM BOTTOM" diagram below for your reference.
VIEW FROM
BOTTOM
Assembly Instructions
BGB 300

55
40 1 2 3 4
55
40 1 2 3 4
STEP3:
A s s e m b l y S t e p 11
Page 13
To Increase Resistance:
1.Increasing the number of bands increases the handlebar
resistance.
2. If you have lessened resistance, you may increase the resistance
again to a maximum of 3 Resistance Bands (#55). Please follow
the proper “To Reduce Resistance” instructions above when
decreasing resistance. You should only need to ‘add’ the top
portion of the Resistance Band (#55) back to the original
position if these instructions were previously followed.
3. Please ensure both the left and right sides have the same number
of Resistance Bands (#55) for balanced handlebar resistance.
4.How To Add The (Top of the) Resistance Band:
Method A
Unscrew the upper Screw (#20) only, slip off the upper
hole of the Resistance Band (#55), then screw back
the upper Screw (#20) to its corresponding hole.
Please do not adjust the lower screw or lower portion
of the band (see above “2.”). Please ensure the Screw
(#20) is secure, but do not over-tighten.
Method A
Unscrew the upper Screw (#20) only, slip on the upper hole of the
Resistance Band (#55) onto the Screw (#20), then screw back
the upper Screw (#20) to its corresponding hole. Please do not
adjust the lower screw or lower portion of the band (see above
“2.”). Please ensure the Screw (#20) is secure, but do not over
-tighten.
Method B
Remove the band from the upper Screw (#20) by
pulling downward and stretching the upper hole of the
Resistance Band (#55) to create an initial opening.
Use this opening to stretch the hole of the band to fit
around, over, and off the Screw (#20). The Resistance
Band (#55) should now ‘pivot’ from the lower Screw
(#20). Please do not adjust the lower screw or lower
portion of the band (see above “2.”).
Method B
Add the band to the upper Screw (#20) by placing the upper hole
of the Resistance Band (#55) onto the upper Screw (#20) and
stretch it downward to create an initial opening. Use this opening
to stretch the hole of the band to fit around, over, and onto the
Screw (#20). Please do not adjust the lower screw or lower
portion of the band (see above “2.”).
Method A
If using Method B, you will be adding/reducing Resistance Bands (#55) from the outtermost edges first.
Resistance Bands Installation
The Resistance Bands (#55) add a realistic feel to the interactive game mode and an extra boost of fitness workout to your
arms and upper body. Increasing the number of bands increases the handlebar resistance for a more engaging workout, while
decreasing the number of bands decreases the handlebar resistance and requires less strength to maneuver.
There are (3) three Resistance Bands (#55) on each side pre-installed on the unit (along with the Lock Pin (#19)). This is the
maximum handlebar resistance you can use on your Game Rider.
To Reduce Resistance:
1.Reducing the number of bands reduces the handlebar
resistance.
2.You need only remove the top of the Resistance Band
(#55). It is not necessary for you to remove the bottom
portion of the band in order to lessen the tension, and
will also prevent the Resistance Band (#55) from
getting lost if not in use.
3. Please ensure both the left and right sides have the same
number of Resistance Bands (#55) for balanced
handlebar resistance.
4.How To Remove The (Top of the) Resistance Band:
Assembly Instructions
NOTE:
BGB 300

04
35
50b
05
Page 14
Your assembly and installation of the bike itself is now complete. However, please continue reading the
remaining sections of this manual in the pages following before you begin using the bike.
A s s e m b l y S t e p 12
Lock Pin
The Lock Pin (#19) allows you to switch the handlebar between fitness bike mode (stationary handlebar) and interactive game
mode (range of motion handlebar).
A.To keep the handle bar stationary:
Align the locking holes and insert the Lock Pin (#19) through the lower hole first followed by the upper hole as shown in the
diagram.
B.To allow range of motion in the handle bar:
Slowly pull the Lock Pin (#19) downward, removing it from the two locking holes.
You may store the Lock Pin (#19) by leaving it the lower Lock Pin hole, or, leave the cord to hang.
AC Adapter
Plug in the AC Adapter for Bike (DC 8V, 1000mA)(#50b) male plug into the rear female socket located on the back of the unit
Shroud (#35).
NOTE: There are 2 different AC adapters
included--1 for the Bike & 1 for the
Wireless Box. Please read the adapter
labels to ensure you are using the proper
one prior to connecting power.
BGB 300
Assembly Instructions

Operation Guide
BGB 
This patented Game Rider is not only a Game Bike but also a full-function Programmable Exercise Bike.
• The Game Bike functions are controlled by four major components:
1) the bike; 2) the monitor buttons; 3) the Wireless Box; and 4) the buttons on the bike handlebar.
• The Programmable Exercise Bike functions are controlled by:
1) the bike; 2) the monitor LCD display & buttons.
There is a “GAME/FIT” button located at the center of the monitor to control the switching between Game Bike
and Programmable Exercise %LNH functions.
This Operations Guide will describe the set-up and operation instructions of the Game Bike and Programmable
Exercise Bike functions in separate sections.
**PLEASE NOTE: The Game Rider is a fitness equipment unit that enhances your workouts with the option of
compatibility to your home television set or PC computer. Please consult the proper product manuals for your
home television set or PC computer and confirm that it can safely connect to the features of the Game Rider.
A.Bike & Monitor: Please follow the Assembly Steps described earlier in this manual to assemble the bike
and to attach the television Monitor (#43) to the bike.
B.Wireless Box:
PLEASE NOTE: the maximum distance between the Game Bike and the Wireless Box (#51) is 25 feet
.
Please ensure there is a clear path from the Game Rider to the Wireless Box without any obstacles
or obtrusions in the way to ensure that the wireless signal properly communicates.
I. SET UP & CONNECTIONS
[GAME] Mode Operation
Wireless Box – Front View
Wireless Box – Rear View
**SYNC (#6) has no function or use on this Game Rider model
Page 15

[GAME] Mode Operation
Page 16
BGB 
B-1. Connect to TV Set:
i. This connection enables user to play the games that are preloaded inside the Wireless Box (#51), and,
display the games on the TV set.
ii. First, connect the single-headed end of the AV Cable to the AV-OUT (#4) port in the rear of the Wireless
Box. Connect the other double-headed end of theAV Cable to the corresponding AV Input ports
on your TV Set. Please connect the cables to the corresponding colors (i.e. yellow to yellow; white to white)
while plugging the cables to the ports on your TV Set.
iii.Then, connect the AC Adapter for WirelessBox (DC 6V, 1000mA) (#50a) toDC (#5) port at the rear of the
Wireless Box and plug into a power source.
B-2. Connect to PC:
i. Alternatively, you may use the bike to play games that are playing on your PC, which include games that
are running directly on your PC, or, games running on Internet web sites.
ii. This connection enables user to play the games that are playing on his/her PC.
iii. First, connect one end of the USB Cable to the USB (#7) port at the rear of the Wireless Box.
Then, connect the other end of the USB Cable to a USB port on your PC.
iv. Since the USB Cable will also transmit the electrical power from the PC, you DO NOT have to connect the
to DC (#5) port at the rear of the
Wireless Box – Connect to TV or PC
*NOTE: There are 2 different AC adapters
included--1 for the Bike & 1 for the
Wireless Box. Please read the adapter
labels to ensure you are using the proper
one prior to connecting power.
AC Adapter for WirelessBox (DC 6V, 1000mA) (#50a)
Wireless Box.

Page 17
[GAME] Mode Operation
I. Playing Games PRELOADED inside the Wireless Receiver Box:
A. Start-Up Procedure:
A-1. Connect the Wireless Box to the TV set: please follow the instructions described in the
“Connect to TV Set ” section above.
A-2. Power ON the Wireless Box by pressing the Power Button (#2) at the front of the Wireless
Box.
A-3. Power ON the TV set, and, use the TV remote controller to select INPUT (usually an “Input” or “AV”
button) to the corresponding AV Input ports (i.e. AV1, AV2, etc.) which you connected the AV Cable
from the Wireless Box .
A-5. Plug in the proper end of the AC Adapter for Bike (DC 8V, 1000mA)(#50b) into the socket located at
the rear end of the bike. Plug in the other end of the AC Adapter to a power source.
A-4. At this point, you should see the Game Menu display on your TV set.
A-6. Press the “GAME/FIT” button on the bike monitor to activate the “GAME” mode.
a. If you see the below display on monitor (with only the MANUAL option on the top line) after pressing
the “GAME/FIT” button, then, you are in “GAME” mode.
b. However, if you see the below display on monitor after pressing the “GAME/FIT” button, then, you are
in “FITness” mode. Press the “GAME/FIT” button again to switch to the “GAME” mode.
You are now ready to play the games while exercising on the bike. Your Game Rider will communicate to the
Wireless Receiver Box, and the gaming visual will be displayed on your TV screen. You should see the
“TVGAMES” (#3) LED in the front of the Wireless Box light up. Please follow the instructions in the
next section to control or manipulate the games.
B. Game Control & Manipulation:
B-1. Buttons on Monitor:
a.There are four buttons (with red icons) on the Monitor in the zone marked “GAME SELECT”. These
four buttons are used in selecting different games or options in games.
NOTE: these four buttons will function ONLY in “GAME” mode. If you find that these four
buttons do not respond when pressed, please press the “GAME/FIT” button to switch to the “GAME”
mode.
b.Button Functions:
↑ : UP UP key in menu selection.
← : LEFT
LEFT key in menu selection.
→ : RIGHT RIGHT key in menu selection.
: EXIT EXIT current selection menu and go to the top menu. Pressing this button in the
middle of game playing will EXIT the current game and go to the top menu for
other game selection.
M
M
GAME MODE
FIT(ness) MODE

II. Playing Games PRELOADED inside the Wireless Box:
BGB 300
DOWN
-
:DOWN
DECREASE the resistance level of the bike during game playing
UP :UP
INCREASE the resistance level of the bike during game playing

[GAME] Mode Operation
B-2. Buttons on Bike Handlebar:
a. There are four colored buttons on the Bike Handlebar.
PLEASE NOTE: these four colored buttons function differently while playing the preload games on
Wireless Box (GR mode) versus while playing the PC games (PC mode). The corresponding
button functions in GR mode and PC mode are marked on top of the buttons and are also color
coordinated.
b. Color Button Functions – while playing preloaded games on Wireless Box (GR Mode):
GREEN button : SELECT To confirm menu selection, or, to START the game. Pressing this
button during the game playing will PAUSE the game.
RED button : BRAKE Press this button during game playing to apply the BRAKE for slowing
down. PLEASE NOTE: this BRAKE function ONLY works in the
“Over Speed” game.
BLUE button : UP UP key in menu selection.
YELLOW button : DOWN DOWN key in menu selection.
B-3. Bike Handlebar:
a. During menu selection, making a LEFT turn using the handlebar is equivalent to pressing the :
LEFT button on the monitor, while making a RIGHT turn using the handlebar is equivalent to pressing
the : RIGHT button.
PLEASE NOTE: If the handlebar LEFT/RIGHT turn function and colored handlebar buttons are not
responding, please peddle on the Game Rider to engage these functions, then proceed again. These
functions stop working when the Game Rider is not actively engaged with the Wireless Box.
b. During game playing, making a LEFT turn or RIGHT turn using the handlebar will change the traveling
direction of the vehicle in the game.
B-4. Playing the Game:
a. Use the buttons on the monitor and the buttons on the handlebar to select the desired game and the
options in selected game.
PLEASE NOTE: Certain options or levels in the preloaded game CANNOT be selected until user has
passed the previous game level.
b. Once the selected game is started, use the handlebar to control the traveling direction of the vehicle
in the selected game.
PLEASE NOTE: The vehicle in the game moves forward by pedaling the bike. The faster you pedal the
bike, the faster the vehicle in the game travels. If you stop pedaling the bike during the game, the
vehicle in the game will stop and some buttons may not function properly.
c. Press the GREEN/SELECT button on the handlebar to PAUSE the game. To exit the game, press the
: EXIT button on the monitor, which will return to the game selection menu.

Page 18
BGB 300