GDI SM560SA User manual

SM560SA Manual 1
SM560SAMAN
SM560SA
MANUAL
56 K SMART MODEM
STAND ALONE
GDI Communications, LLC
Verdi, Nevada

SM560SA Manual 2
SM560SAMAN
SM560SA MANUAL
REV. B
GDI Communications, LLC
280 Interstate 80 Exit 1
Verdi, Nevada 89439
775-345-8000
This Manual applies to units with serial numbers 00000 and above
Drawing Number: A00350
APPROVED:
Engineering_______________________________ Date_______________
Manufacturing_____________________________ Date _______________
Marketing_________________________________ Date _______________
Release Date___________________

SM560SA Manual 3
SM560SAMAN
TABLE of CONTENTS
GENERAL DECRIPTION……………………………………………..4
SPECIFICATIONS…………………………………………………….4
INSTALLATION………………………………………………………5
AT COMMAND SET …………………………………………………7
TABLES
DB-9 PIN-OUT………………………………………………….……5
RJ11 PIN-OUT………………………………………………….…….5
170 CONNECTION CHART…………………………………………6

SM560SA Manual 4
SM560SAMAN
DESCRIPTION
The SM560SA is a 56 Kbps dial-up
Modem in a standalone case. It is
completely compatible with other V.34 AT
command set Modems and is designed for
traffic control environments. The
SM560SA has a built in power supply and
plugs into a standard outlet. The
SM560SA-12 connects to a 12VDC
supply. The Black wire from the cord is
connected to +12V and the white wire is
connected to Ground. The SM560SA
comes standard with an RS-232 port that
connects to a Computer or Traffic
controller through a DB-9 (female)
connector on the back panel. The phone
line connects to the SM560SA through a
standard RJ-11 connector. The SM560SA
can not be used with leased lines. A second
RJ-11 connector can be used for a phone
connection.
The SM560SA can operate at 56 Kbps and
automatically fall back all the way down to
300 baud. The Modem speed can also be
set using the AT commands if wanted (see
AT Command listing). The serial port has a
maximum speed of 115.2 Kbps and is RS-
232 and V.24 compatible. An RS-485
option is also available using the same DB-
9 connector.
A speaker is included internal to the
Modem so that call progress can be heard.
The speaker is controlled through standard
AT Commands. Front panel LEDs show
the status of the Modem. The SM560SA
has Auto Answer, Auto Dial, and tone or
pulse dialing. A front panel switch allows
you to set DTR active all the time if DTR
is not available. Front panel dip switches
also allow you to invert the RS-485 data
and control signals if that option is
installed.
SPECIFICATIONS
ENVIRONMENTAL
Temperature Range……..-37°to +74°C
Humidity ..….5 to 95% non-Condensing
POWER
Voltage………..90 to 130 VAC or
189 to 260 VAC
Frequency………47 to 63 Hz
Power…………..6 Watts Max
+12 Volt version….12 VDC @ 0.5A
PHYSICAL
5.7”W x 8.5”D x 1.5” H
Weight……………~3 lbs.
MODEM
Modulation……..Quadrature Amp. Mod.
Compatibility:
Modem…………ITU V.90, V.34 and
Rockwell V.FC
Interface………..ITU V.24/V.28,
EIA-232, and EIA-485
Data Throughput…..115.2 Kbps
Data Rates……56Kbps, 33.6Kbps,
31.3Kbps,
28.8Kbps, 26.4Kbps,
24.0Kbps, 21.6Kbps,
19.2Kbps, 16.8Kbps,
14.4Kbps, 12.0Kbps,

SM560SA Manual 5
SM560SAMAN
9.6Kbps, 7.2Kbps,
4.8Kbps, 2.4Kbps,
1.2K baud, 300 baud. The
Modem will automatically select
the best operating speed. Speeds are
±0.01%.
Specifications:V.90, 56Kflex, V.34,
V.32 bis, V.32,V.22
bis, V.22A/B, V.23, V.21,
Bell 212, Bell 103, V.33,
V.17, V.29, V.27 ter, V.21
Channel 2
Error Correction….V.42 LAPM, MNP2-4,
MNP10
Data Compression…V.42 bis, MNP 5
Loop Tests…..ITU V.54 loop2 (RDL) and
Loop 3 (LAL)
Transmit and Receive Frequencies:
Data Carrier…….1800 ±0.5 Hz
Calling Tone……1300 ±10 Hz
Answering Tone…2100 ±15 Hz
Receiver Freq. Tol…….±14 Hz
Receiver Performance
S/N Ratio…………..-26 dB
Dynamic Range……-12 dBm to –42 dBm
Transmit Level
Fixed at –11 ±2 dB
Ring detect Sensitivity…. 38 VRMS
LINE INTERFACE
Ring Equiv. Number….…1 Bel
Terminating Imped………600 Ohm
Return Loss…Better than 14 dB between
200 and 4000 Hz
DB-9 PIN-OUT
Pin No. EIA-232 EIA-485
1 DCD (out) TXD+
2 RXD (out) TXD-
3 TXD (in) RXD+
4 DTR (in) RXD-
5 GND GND
6 DSR (out) RTS+
7 RTS (in) RTS-
8 CTS (out) CTS+
9 RI (out) CTS-
INDICATORS
POWER, TXD, RXD, DTR, DSR (OH),
DCD, RI.
Th SM560SA can store 2 user profiles and
4 phone numbers. The numbers can have
up to 32 digits.
INSTALLATION
The SM560SA comes from the factory set
up for 90 to 130 VAC. If 180 to 260 VAC
operation is required, the Zero Ohm
jumpers labeled “110VAC” (R8 and R9)
should be removed and the Zero Ohm
Jumper labeled “220VAC” (R10) installed.
These jumpers are located between the
transformer and the fuse on the PC Board.
The SM560SA-12 connects to a 12 Volt
DC supply rated at least to 0.5A. The
Black wire connects to +12V and the white
wire connects to Ground. The green wire is
Chassis Gnd.

SM560SA Manual 6
SM560SAMAN
The Phone line is connected to the RJ11
connector on the back panel labeled
“LINE”. An exterior phone can be
connected to the RJ11 labeled “PHONE”.
The RJ11 connectors are connected in
parallel so do not use the phone while the
modem is being used.
RJ11 PIN-OUT
2 TIP
3 RING
The DB-9 connector is pinned out so that a
one-to-one cable is needed to connect to
most computers. Since most computers use
a DB-9 connector with male pins, the cable
will need to have one female and one male
connector on it.
A special cable will be needed if you have
the RS-485 option since there is no
standard pin-out for RS-485 with this
connector. The DB-9 is pinned out
according to the way CALTRANS has
defined it on the 2070-7.
The connection chart for a 170 type
controller is shown below:
170 Connection Chart
Function DB-9 170 C2,20
TXD 3 K
RXD 2 L
RTS 7 J
CTS 8 M
DCD 1 H
GND 5 N
As can be seen from the Chart, the 170
doesn’t use DTR and DSR. DTR can be set
up to be ignored by the Modem with an AT
command. DTR can be permanently
asserted with the front panel switch if you
don’t want to use the AT command.
485 OPTION
The SM560SA has the 120-Ohm
termination resistors built into the unit on
the input lines (TXD and RTS). This
Modem is not designed to be used in an
RS-485 Multi-drop system.
The polarity of theRS-485 signals can be
inverted if needed by two front panel dip
switches. The Switch labeled “DATA” will
invert the TXD and RXD signals and the
Switch labeled “CTR” will invert the RTS
and CTS signals. These Switches have no
affect on RS-232 operation.
Indicators
The Indicators on the front panel give the
status of the SM560SA.
POWER………Indicates that the Power
Supply is operating.
TXD…………Indicates that data is being
Transmitted
RXD………….Indicates that data is being
Received
DTR……….. Indicates that Data terminal
Ready is true.
DSR (OH)…..Indicates that Data SET
Ready is true. It is also
An indicator of the OFF
Hook condition.
DCD…………Indicates that the modem
Is detecting a carrier.
RI……………Indicates that the Modem is
Receiving a Ring signal.

SM560SA Manual 7
SM560SAMAN
There are no adjustments or user selectable
features inside the Modem. There is no
preventative maintenance required or
anything that needs to be adjusted for the
life of the product.
The following pages contain a summary of
the AT Commands and “S” Registers that
the SM560SA responds to. The factory
default settings are also shown. A complete
definition of the AT commands is too large
for this Manual (174 pages). If one is
required, a PDF file (450K) can be sent
electronically to you.

SM560SA Manual 8
SM560SAMAN
BILL OF MATERIAL
FOR THE
SM560SA
RS-232 VERSION
Item PART
NUMBER Qty DESCRIPTION REFERENCE
1 PCB-336SA 1 PC Board for the Sm336SA Rev. B 1
2 FP-560SA 1 Front panel w/silkscreen 2
3 BP-560SA 1 Back panel w/silkscreen 3
4 P/CORD-18/3B 1 Power cord, 18 AWG 4
5 SR-1150 1 Strain Relief, Power Cord, Heyco 5
6 LANSING/TOP 1 Lansing Top 6
7 LANSING/BAS
E 1 Lansing Base 7
8 LANSING/BEZ
L 1 Lansing Bezel 8
9 LANSING38695 4 Screw, 4-40
10 LF-3A/G- ½ A 1 Fuse, ½ A Slow Blow
11 Box-12X9X3 1 Shipping Box 9
11A TYWRAP-
3.9WH 2 Ty-wraps 4” for tying down U9 U9
12 V.90/56-MMC 1 SocketModem Conexant 56k V.90, K-
flex U9
13 74HC-86 1 EX-OR Gate, quad, U6
14 14C88 1 RS-232 Driver, Quad, CMOS U7
15 00386 1 Audio Amp, LM386CN U5
16 MAX-232 1 RS-232 Rec., Driver, 5V U3
17 LT-1129CT-5 1 Regulator, 5V, LOH, w/Shut off, TO-
220 U1
18 01233-5 1 Voltage Monitor DS1233-5, TO92 U10
19 2N7000 7 Transistor, 2N7000, MOSFET Q1,7
20 1N5233 1 Zener, 1N5233, 5.1V Z3
21 1N4004 2 Diode, 1N4004, 1 Amp, 400V D1,2
22 SA26A 1 Tranzorb, 26V Z2
23 V275/350-S 1 SIDACTOR, Teccor P3100BA70,
310V Z1
24 LED-CR 7 LED, RED, Clear Lens DS1,7

SM560SA Manual 9
SM560SAMAN
Item PART
NUMBER Qty DESCRIPTION REFERENCE
25 V150LA10 3 MOV, 150V 50J MOV1,2,3
26 102K1000-CDR 2 Capacitor, 1000pF, 1000V, Ceramic
disc C22,23
27 473M050-DCR 1 Capacitor, 0.047uF, 50V, ceramic C13
28 104K050-DCR 15 Capacitor, 0.1uF, 50V, ceramic C3-6,8-12,14-
16,18,21,24
29 106K025-TTR 3 Capacitor, 10.0uF, 25V Tantalum C19,20,25
30 107M025-AER 1 Capacitor, 100 uF, 25V Electrolytic C7
31 227M035-AER 1 Capacitor, 220 uF, 35V Electrolytic C17
32 108M025-AER 2 Capacitor, 1000 uF, 25V Electrolytic C1,2
33
34
35 02505-000 3 Resistor, 0 Ohms R8,9,12 (opt
R14)
36 02505-100 1 Resistor, 10 Ohms, ¼ W, 5% R13
37 02501-1001 10 Resistor, 1.0 K, ¼ W. 1% R1-7,11,15,16
38 02501-3011 1 Resistor, 3.01 K, ¼ W, 1% R17
39 02501-4751 3 Resistor, 4.75 K, ¼ W, 1% R20,21,23
40 02501-2321 1 Resistor, 2.32 K, ¼ W, 1% R22
41 PDT-2 1 Switch, push button SW2
42 SPST—3SA 1 Switch, dip, 3 position side actuated SW1
43 PH3TB-MKDS 1 Terminal Block, 3 position, Phoenix J4
44 RJ11C-RA/PC 2 RJ-11 Phone Jack, PC mount J1,2
45 9DSC-FRA/PC 1 Connector, DB-9, Female, PC mount J3
46
47 LP20-300B7 1 Transformer, 20V, PC mount T1
48 FERBEAD-85A 8 Ferrite Bead, TDK BF45-4001 L2-9
49 FERBEAD-
400W 1 Wound Ferrite Bead, Fair-Rite 2961666681 L1
50
51 10SIL-TH/SKT 2 Socket, 10 Position SIP, SAMTEC A9
52 IC-SKT4 2 Socket, 4 Position SIP, SAMTEC A9
53 LFH-HLDR/PC 1 Fuse Holder, Littlefuse F1
54 LFH-K/3AG 1 Fuse Holder Casing F1
55 M/SPKR-SQ/2 1 Speaker SPKR1
56 MS3-48X3/8PP 2 Screw, 3-48 3/8” SPKR1
57 HN3-48SS/S 2 Nut, 3-38 SPKR1
58 H/SINK-FIN 1 Heatsink, TO-220 HS1
59 MS4-40X3/8P 1 Screw, 4-40 X 3/8” HS1
60 HN4-40Z/M 1 Nut, 4-40 HS1
61 CL/SPRAY A/
R Conformal Coating 10

SM560SA Manual 10
SM560SAMAN
Item PART
NUMBER Qty DESCRIPTION REFERENCE
62 A/
R Heatsink compound HS1