manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. GE
  6. •
  7. Dishwasher
  8. •
  9. GE Spacemaker PDW1800N Manual

GE Spacemaker PDW1800N Manual

Dimensions and Installation Information (in inches)
For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
ge.com or call GE Answer Center®service,
800.626.2000.
PDW1800/60N
GE Profile™18" Built-In Dishwasher
Specification Revised 2/09 250218
Listed by
Underwriters
Laboratories
Electrical Rating
Voltage AC..........................................................120
Hertz.......................................................................60
Total connected load amperage...............9.0
Calrod®heater watts max......................... 550
For use on adequately wired 120-volt,
15-amp circuit having 2-wire service
with a separate ground wire. This appliance
must be grounded for safe operation.
Note: Dishwasher must not be installed
more than 10 feet from sink for proper
drainage. All plumbing and electrical work
must be in accordance with local codes.
Installation Information: Before installing,
consult installation instructions packed with
product for current dimensional data.
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
18*
22-1/2
Max.
25
32-1/2
to
35**
1-1/2"
90°
34-1/4" Min.
24"
Bottom
of tub
to floor
7"
Hot Water
Line
Electrical
Wiring
17-5/8" to 18" Min.
1-1/2"
From back of
rear frame
to wall
3"
90°
Electrical, drain and
water supply line
entrances must
be confined to
shaded areas to
avoid interference
with components
White (neutral)
Black (line)
Ground
Dishwasher Countertop
2" Minimum
Dishwasher
Door
*Width adjustable from 17-5/8" to 18".
**Meets ADA countertop height requirement of 34".
For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
ge.com or call GE Answer Center®service,
800.626.2000.
PDW1800/60N
GE Profile™18" Built-In Dishwasher
Specification Revised 2/09 250218
Listed by
Underwriters
Laboratories
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
GE Pub. No. 031-30244
Custom Dishwasher Door Panel Template
For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
ge.com or call GE Answer Center®service,
800.626.2000.
Top of Panel
7-11/16"
Trim Around
Dotted Line
2-5/32"
(5.5 cm)
(19.5 cm)
Trim Around Dotted Line
Drill 3/32"
Pilot Hole
3/32" Deep
Top of Panel
7-11/16"
2-5/32"
(5.5 cm)
(19.5 cm)
Drill 3/32"
Pilot Hole
3/32" Deep
Drill 3/32"
Pilot Hole
3/32" Deep
13/32"
(1 cm)
6-1/2"
(16.5 cm)
5-29/32"
(15 cm)
Drill 3/32"
Pilot Hole
3/32" Deep
13/32"
(1 cm)
6-1/2"
(16.5 cm)
5-29/32"
(15 cm)
3/4" Thick Custom Panel
Template Instructions for 18"
Top Control Integrated Prole and
Monogram Dishwasher Models
Pub. No. 31-30244
Dwg. No. 206C1559P182
05-08 JR
The custom panel should be sized to your installation situation. See Step 1. For easier
installation, the custom panel and custom handle should be attached before installing the
dishwasher.Use this template to locate mounting screws and spacers on the custom panel.
IMPORTANT
• A custom handle must be installed onto the custom
panel. Install the custom handle 4-1/2" max. from
the top of the panel.
STEP 2 DRAW CENTERLINE
• Placethecustom panelon a surface with the
appearanceside down.
• Locatethevertical center of thepanel at the top.
• Useacarpe nter's square todraw a centerlinefrom
topto bottom.
STEP 3 ALIGN TEMPLATE TO PANEL
• Trimtemplateonthe dottedlinealong all sides.
• Placethetemplateon the panelaligne dwithth e top
edgeand the centerline. Use tape to holdin place.
IMPORTANT:If the template is not aligned with the top
edge of the panel, the 1/2" minimum gap will not be maintained.
This 1/2" minimum gap must be maintained to prevent condensation
and damage to the control panel from screw heads.
• Useanawl to mark the screw hole locations indicated
onthe template.Removethetemplate.
HEIGHT
Panel height should be 26-25/32" (68 cm).
• Thetop of thecustom panelmust be
withthe topof the door.The 1/2"minimumgap
betweenthetop of the door and the bottomof
thecountertopmustbe maintained.
PARTSINCLUDED:
(2) Brackets
(4) 1/2" Phillips at-head screws
(2) Spacer pads
(2) Metal spacers
(2) 1" Phillips at-head screws
(2) 3/4" Phillips round-head screws
STEP 1 CUSTOM PANEL SIZE REQUIREMENTS
IMPORTANT:To ensure optimum door balance
performance, the custom panel must not weigh
more than 8 lbs.
WIDTH
Panel width must be 17-1/2" (44.4 cm).
• If the panelwidthis less than17-1/2",itwill
notcover the dishwasher frame.
STEP 7 CHECK DOOR BALANCE
Tocheck the doorbalance, holdth etop of the
dishwasher
• Checkth edoor balance by openingand closing
thedoor.
• Ifthedoordrops whenreleased, increase the
springtension.If th edoorrises whenreleased,
decrease thespring tension.
• Usinga T25 torquedriver,adjust in the direction
shown.Adjust bothsides equally.
STEP 6 INSTALL ASSEMBLED PANEL
• Securethepanel to the doorby inserting
thetop metalspacers andbottombrackets
intothe matchingslots on the dishwasher
doorand controlpanel.
• Makesure bothmetalspacers and both
brackets engagethe slots.
• Pressthe panelagainst th edoor and push
downwarduntilthemetal spacers andbrackets
are fully engagedintothe slots. The panel should
alignevenly withth etop and sides.
• Standthe dishwasher upright.
• Openthedishwasher door and removethe
2 plugbuttons,oneon each side as shown.
• Placethesupplied3/4"Phillips round-head
screws inside the plastic sleeve and drive
throughtheinnerdoor and intothe custom
panel.
• Replacethe2 plugbuttonsby pressing them
back intothe plastic sleeve.
WARNING: Donot overtightenscrews. Excessive
tighteningof thescrews coulddamagedoor edges.
STEP 5 INSTALL CUSTOM HANDLE
A customhandle mustbe installedonto thepanel
beforethe panel is secured to th e dishwasher door.
• Thehandle shouldbe installed so that it aligns with
adjacentdrawer handles, or 4-1/2"max.fromthe
topof the panel.Secure th ehandle in thesame
manneras thecabinet handles.Screws must be
countersunkintothe panel.
STEP 4 INSTALL MOUNTING SCREWS AND SPACERS
Note:The custompanel is secured to the dishwasher door
withthe metalspacers, screws and brackets provided.
The metalspacers and brackets will slip intothe slots
onthe dishwasher door and controlpanel.
• Alignthe metalspacers overthe toppilotholes. Ensure
thethick, recessed sideis facing up.
• Drivethe supplied1"Phillips screws through
themetal spacers andintothe panel.
• Alignthe brackets over the bottompilotholes.Ensure
thecurved lipis facing up. If the back surface of the
panelis not use the spacer pads provided.
• Drivethe 1/2"Phillips screws throughthe
brackets and intothe panel.
Countertop
Minimum 1/2" gap
for clearance
1/2" minimum
Mark center
screw holes
Bracket
Spacer Pad Spacer
Handle
4 1/2" Max.
from top
of panel
Custom
door panel
Screws must be counter-
sunk into panel
Custom
panel
Dishwash-
er door
Custom panel
PARTS SUPPLIED
(2) Brackets(2) Spacer Pads (2) Metal spacers
(2) 3/4" Round-head
screws (4) Phillips at-head
screws
(2) Phillips at-head
screws
Increase
Decrease
Decrease
Increase
Instructions de gabarit pour panneau
sur mesure épais de 19 mm (3/4 po)
pour modèle de lave-vaisselle à réglage
intégré en haut Prole et Monogram
Le panneau de nition doit avoir des dimensions appropriées pour l’installation. Consulter l’étape 1.
Pour faciliter l’installation, le panneau de nition et la poignée de nition doivent être montés avant la mise
en place du lave-vaisselle. Utiliser ce gabarit pour déterminer l’emplacement des vis de montage et
des rondelles sur le panneau de nition.
IMPORTANT
le panneau de nition. Installer la poignée à
moins de 11,5 cm (4-1/2 po) du haut du pan -
neau.
ÉTAPE 2 TRAÇAGE DE L’AXE
• Mettre le panneaude surune surface plate, le côté extérieur
vers le bas.
• Mettre le centre vertical du panneauen haut.
• Avec une équerre de menuisier,tracer un axe du haut au bas.
ÉTAPE 4 INSTALLER LES VIS DE MONTAGE ET LES RONDELLES
ÉTAPE 5 INSTALLATION DE LA POIGNÉE DE FINITION
• Mettre le lave-vaisselle debout.
• Ouvrirla portedu lave-vaisselle et visser les vis à têtebombée
fourniesnº 8 x 1-3/4po.Visser une vis enhaut et une en bas, à
travers le panneauinternede la porteet le panneaude
ATTENTION: Il nefaut pas serrer les vis en excès. Un serrage
excessif des vis peutendommagerles bordsde la porte.
• Couperle gabaritsuivant le pointillé,sur tousles côtés.
• Mettre le gabaritsur le panneau,aligné sur le bordsupérieuret sur l’axe.
Le maintenirenplace avec du rubanadhésif.
IMPORTANT: Si le gabarit n’est pas aligné à l’extrémité du haut du panneau,
vous n’obtenez pas 1/2 po d’espace libre. Vousdevez avoir un espace libre de
1/2 po pour empêcher la condensation et éviter d’endommager le panneau de
contrôle avec les têtes de vis.
• Avec unpointeau,marquerles emplacementsdetrous de vis indiqués
sur le gabarit. Enlever le gabarit.
HAUTEUR
Le panneau doit avoir entre au moins 30 1/16 po et 30 1/4 po
de hauteur.
• Sile panneaua plus de 30 1/4po de hauteur,il empêchela
portede s’ouvrir complètement.
• Sile panneaua moinsde 30 1/16pode hauteur,il ne couvre
pas le châssis deportedu lave-vaisselle.
Numéro de publication 31-30569-1
Nº de plan 206C1559P109
07-04 JR
PIÈCES INCLUSES :
(4) Rondelles
(4) Vis nº 8 x 5/8 po à tête bombée Phillips, en acier inoxydable
(3) Vis à bois nº 8 x 1-3/4 po à tête bombée Phillips, en acier
inoxydable
(2) Ressorts pour service sévère
ÉTAPE 1 T AILLE NÉCESSAIRE POUR LE PANNEAU SUR MESURE
Si l’épaisseur dupanneau est inférieure à 19mm(3/4po), il faututiliser des vis
pluscourtes. Utiliserdes vis nº 8 x 1/2po (pas fournies) pour les panneauxde
13mm(1/2po).
• Utiliser une mèche de 2,4 mm(3/32po) pourpercer des trous guides à u ne
profondeurde2,4mm(3/32po)aux emplacementsmarqués.
Remarque : Le panneaude estmaintenuen place sur la portedulave-
vaisselle avec des rondelleset des vis fournies. La rondelleglisse dans les
trousallongés dans la porte dulave-vaisselle.
• Visser les vis nº 8 x 5/8po à têtebombéePhillips, en acier inoxydable(four-
nies) à travers la rondelle et dans le panneau.
• Installer les rondelleset les visrestantes, commeindiqué,aux endroitsmar-
qués.
IMPORTANT : Pour que la porte fonctionne
bien, le panneau sur mesure ne doit pas
peser plus de 6,4 kilos (14 livres).
CONSEIL – Si la portene s’ouvre pas facilementou si elle
tombetroprapidement, le passage du câble des
ressorts. Le câble est maintenuenplace par des
« épaulements» sur la poulie. quele câble n’a pas
glissé sur les épaulementsdepoulie.
IMPORTANT– Régler l’équilibredes deux ressorts pour
avoirla mêmetensiondes deux côtés, d’éviterun
gauchissementexcessif de la porteen service.
ÉTAPE 3 ALIGNER LE GABARIT SUR LE PANNEAU
Installer unepoignéede sur le panneauavant de monter
le panneausur la portedu lave-vaisselle.
• Il faut alignerla poignéesur les poignéesdes tiroirs adjacents
ouà moinsde 115mm(4-1/2po)du haut dupanneau. Monter
la poignéede la mêmemanièreque les poignéesde l’armoire.
Les vis doiventêtrenoyées dans le panneau.
ÉTAPE 6 INSTALLATION DU PANNEAU ASSEMBLÉ
• Pour monterlepanneau sur la porte,insérer les vis de montage
duhautet du bas, avec les rondelles,dans les trous allongés
correspondants.
• que les quatrerondelles s’engagentdans les trous
allongés.
• Pousser le panneau contre la porte et l’abaisser jusqu’à ce
queles rondellessont totalementengagéesdans les trous al-
longés.Le panneaudoit être alignéuniformémentenhaut
etsur les côtés.
ÉTAPE 7 INSTALLATION DES RESSORTS DE LA PORTE
Le lave-vaisselle est expédiéde l’usine avec unjeu de ressort s
d’équilibretemporaires.Il faut utiliser les ressorts pourservice
sévère fourniset le s trous de réglage ducâble pouréquilibrer
la porteaprès avoir installé le panneau de nitionsur le
lave-vaisselle.
• Avec le lave-vaisselle sur la paletteen bois, fermeret ver-
rouillerla porte.
• Enlever et jeterles deux ressorts de la porte .
• Monterles nouveauxressorts pour service sévère de la porte.
Engagerl’extrémitéavec un crochet courtdans la patte de
supportetcelle avec le crochet longdans le câble.
• Ouvriret fermer la porte.
• Si la porte s’ouvrequandelle est relâchée, augmenterla ten-
siondu ressort. Si la portese ferme quandelle est relâchée,
diminuerlatension duressort.
• Lehautdu panneausur mesure doit le hautde la
porte.Il doity avoir un espace libre d’au moins1/2 poen-
trele haut de la porteet le bas durevêtementde comptoir.
LARGEUR
Le panneau doit avoir au moins 23 3/4 po de largeur.
• Sile panneaua moinsde 23 3/4po de largeur,il ne couvre
pas le châssis deportedu lave-vaisselle.
For Reference Only
Not to Scale
Order GE Pub. No. 031-30244
Call 1-800-626-2000
For a full-size panel template with complete
panel installation instructions.
PDW1800/60N
GE Profile™18" Built-In Dishwasher
Specification Revised 2/09 250218
PDW1800NSS
ON
OFF
TIME
DELAY
CYCLE
SELECT
1-24HR.
RINSEAID
HEAVY NORMAL LIGHT GLASSESRINSESPEED SOAK
Features and Benefits
• Bright Annealed Stainless Steel Interior - A lustrous finish and lasting beauty that resists
stains and corrosion
• Hidden Electronic Controls - Tucks easy-to-use controls out of sight inside the door's
top edge
• SpeedWash Cycle - Saves time by washing dishes faster
• Glasses Cycle - Gently washes glassware; great for entertaining
• Air-Dry Cycle - Washes lightly soiled dishes without a heated dry
• Nylon Racks - Heavy-duty design secures and protects dishes during each cycle
• 1-24-Hour Delay Start - Offers the ability to start the dishwasher when no one's home
• Model PDW1800NSS -Stainless steel
• Model PDW1800NWW -White
• Model PDW1800NBB -Black
• Model PDW1800NII -Custom panel

Other manuals for Spacemaker PDW1800N

1

This manual suits for next models

4

Other GE Dishwasher manuals

GE Profile PDW9700N User manual

GE

GE Profile PDW9700N User manual

GE Built-In Dishwashers User manual

GE

GE Built-In Dishwashers User manual

GE Cafe CDWT280VSS User manual

GE

GE Cafe CDWT280VSS User manual

GE GSC3200J User manual

GE

GE GSC3200J User manual

GE GLDT696D00SS User manual

GE

GE GLDT696D00SS User manual

GE GSD820 User manual

GE

GE GSD820 User manual

GE Spacemaker GSM1860NSS User manual

GE

GE Spacemaker GSM1860NSS User manual

GE GLC4000 Series User manual

GE

GE GLC4000 Series User manual

GE GSC3500NWW User manual

GE

GE GSC3500NWW User manual

GE Profile PDW8700 Series User manual

GE

GE Profile PDW8700 Series User manual

GE GDT530 SEries User manual

GE

GE GDT530 SEries User manual

GE GDF510PSDSS Manual

GE

GE GDF510PSDSS Manual

GE CDWT980RSS - Cafe 24" Tall Tub Dishwasher User manual

GE

GE CDWT980RSS - Cafe 24" Tall Tub Dishwasher User manual

GE GSD3800 User manual

GE

GE GSD3800 User manual

GE Monogram ZBD1800K Series How to use

GE

GE Monogram ZBD1800K Series How to use

GE Monogram ZBD8920PSS User manual

GE

GE Monogram ZBD8920PSS User manual

GE Profile PDW9200 Series How to use

GE

GE Profile PDW9200 Series How to use

GE GLD4500N Manual

GE

GE GLD4500N Manual

GE GDF540HSDSS Manual

GE

GE GDF540HSDSS Manual

GE GSD3360DSS Manual

GE

GE GSD3360DSS Manual

GE ZBD 5600 User manual

GE

GE ZBD 5600 User manual

GE Profile PDWT502VII Manual

GE

GE Profile PDWT502VII Manual

GE Profile PDW8680N User manual

GE

GE Profile PDW8680N User manual

GE Monogram ZDT975SIJII User manual

GE

GE Monogram ZDT975SIJII User manual

Popular Dishwasher manuals by other brands

Hotpoint Ariston LDF 1235 operating instructions

Hotpoint Ariston

Hotpoint Ariston LDF 1235 operating instructions

Bosch SP Series instruction manual

Bosch

Bosch SP Series instruction manual

Tappan TDT4030B user manual

Tappan

Tappan TDT4030B user manual

Siemens SX63H800BE user manual

Siemens

Siemens SX63H800BE user manual

AEG FSE64606P user manual

AEG

AEG FSE64606P user manual

Kenmore 665.1772 Series Use & care guide

Kenmore

Kenmore 665.1772 Series Use & care guide

Bosch SMV4ECX16E INFORMATION FOR USE

Bosch

Bosch SMV4ECX16E INFORMATION FOR USE

Maidaid Halcyon Evolution 515WS Installation and user guide

Maidaid Halcyon

Maidaid Halcyon Evolution 515WS Installation and user guide

THOR HDW2401SS Use & care manual

THOR

THOR HDW2401SS Use & care manual

Hanseatic HGTI6082C14T7735ES user manual

Hanseatic

Hanseatic HGTI6082C14T7735ES user manual

Smeg LF-455IT instruction manual

Smeg

Smeg LF-455IT instruction manual

Danby Designer DDW1802W instruction manual

Danby

Danby Designer DDW1802W instruction manual

Zanussi ZDT21006FA user manual

Zanussi

Zanussi ZDT21006FA user manual

Maytag MDBTT75AWS Use & care guide

Maytag

Maytag MDBTT75AWS Use & care guide

Bosch SHU33A use and care manual

Bosch

Bosch SHU33A use and care manual

Frigidaire 100 series Use & care manual

Frigidaire

Frigidaire 100 series Use & care manual

Grundig GSV41921 User instructions

Grundig

Grundig GSV41921 User instructions

Miele G 7966 operating instructions

Miele

Miele G 7966 operating instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.