GE JX2127 User manual

Installation
Instructions Built-In TrimKits
JX2127andJX2130
Questions?Call GEAnswer Centerat 800.626.2000or Visito,u-X_bsite,t: www.GEAppliances.com ]
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - S.,ethese
inst_ uctions fin" local inspector's use.
• IMPORTANT - Obse,.e.U
governing codes and ordinances.
• Note to Installer -Be sure to leave these
instructions with the Consumer.
° Note to Consumer - KeeI)these instructions
tot fllttu'e reference.
• For easier installation and personal safety, we
recommend that two people install this microwave oven.
• Unplug the microwave oven beflwe attempting
installation of this kit.
FOR YOUR SAFETY:
WARNING -Bef.,ebeginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely tasten
a prominent warning device, such as a tag, to the
service panel.
TOOLS YOU WILL NEED
#2Phillipsscrewdriver
Pencil
Awl or punch
Drill with 7A/' bit or#35
Scissors(optional) Tapemeasure
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Skill level - Installation of this appliance requires basic
mechanical and electrical skills.
° Completion time - 1-3 horn's
• Proper installation is the responsibility of the installer,
•Product failure due to improper installation is not
covered trader the _4"u'rantv.
This kit is UI, listed for installation ahme or over
any (;eneral Electric/Hotpoint/RCA single electric
wall o_,eil.
PARTS iNCLUDED
PART OUANTtTY
TrimFrame 1
BottomDuct 1
TopBracket 1
PhillipsRound-Head
Screws 36
(27bronze,
9 color-matched,
24 requiredfor
installation)
PhillipsFlat-Head 12
Screws (2 requiredfor
installation)
Anti-TipBracket 1
BottomBracket 1
Template 1

Installation Instructions
CUTOUT DiMENSiONS
Models
Height
Width
Depth (nfin.)*
*Min. depth with rece
Min. depth with rece
27 tr
16%"
25½"
19½" or 22"
1.½
)ta(le Olltside (;tbii/et QI 9"
m_(le inside _abinet 22"
1%"overlap ...........
30"
16:_"
25½"
19½" or 22"
Depth
1" Clearancebeyond 1" overlap
TrimFrame
(onall sides)
ACAUTION
This trim kit uses air flow fl'om tile top, bottom and
sides of tile trim frame. Blocking tile air flow can
cause tile microwave to flmction improperly and
Ill,IV C_ltlSe dalllage to tile illicYowave.
Allow a 1" clearance beyond tile edge of tile Trim
Frame to provide proper air flow.
On 27" models, allow 1 i/_,, at tile top, !_;" on tile sides
and l" at tile bottom for oxerlap of tile Trim Frame
oxer tile edges of tile cutout.
l zt
On 30" models, allow l ¼ at tile top, 2JA" on tile sides
and l" at tile bottom for oxerlap of tile Trim Frame
oxer tile edces of tile cutout.
INSTALL BOTTOM BRACKET
AND BOTTOM DUCT
_Fit tile tab tile bottom bracket tile slot
into
(111 oil
tile back of tile 1)ottom duct, and push down until
tile bracket is flush with tile bottom of tile duct.
Fasten tile bottom bracket to tile bottom duct b_
rising two bronze ro/ind-head screws.
_ Disconnect tile microwa',e o',en 1)elore _roceeding
I ,
with tile installation.
Front
Rear
Screws
_ Remove any loose items inside tile microwave
oven, including tile tm'ntable and turntable
support. Careflfllv tm'n tile microwave oven
upside down.
_ I,ine tile tabs tile bottom duct with tile slots
lip Oil
on tile bottom of tile microwave and insert tile
tabs into tile slots. Secm'e the bottom duct with
four bronze ro/md-head screws as shown.
f Screws
I % _ Screws
, i
Microwave Oven Upside Down
2

mnstaJiation mnsttuctions
| iNSTALL THE ANTbTJP BRACKET
[_ l_)raw a lim_e o]_ the cutout Iqoor at the ce]_ter of
the cutouL amid exteN_d the lim_e _" dow]_ the g_ce
of the cabim_et.
_Fo]d or c_t the f_xmt edge of the template, a]<mg
the {_xmt g_fide ]h_e_ Place the template fi_s]]
a]oi_g the f_xmt edge of the cl_tol_t floo_; a]]gn]m_g
the ce]lter ]im_e of the template _it]l the ce]lter ]im_e
of the clltoIlt floor. Mark the ce]/ters of the t_ko
scre_ holes _it]] am_ a_] or ce]_ter preach f_r the
am_ti-ti I) bracket ]ocatio]_ as show]_.
//
Cutout Floor
_ Remove the template amid drill two holes for the
a m_ti-ti p bracket.
Screws
'I
Anti-Tip
>-<. Bracket
_ l_sta]l the a_ti-tip bracket o_to the cutout floor
Iosi_ rt'wo bi"o_ze i'olH_d-]_ead sc]'ews.
1-_ INSTALL MICROWAVE OVEN
INTO CABINET
_ Slide the microwave oxen part way into the cabinet
oi)ening.
[_] Plug in the microwaxe oxen.
BottomDuct sembly
Anti-Tip
Bracket
[]
[]
[]
Bottom Bracket
The bottom bracket must be fiat to the cutout
floor to engage correctly with the anti-tip bracket
as shown. Careflfllv slide the microwave oven back,
engaging the anti-tip bracket. Make sm'e the
power cord is not mashed or cut as VOlt slide the
microwave into place.
Center the microwaxe oxen within the
ct/to/It ol)enin_,.
Ensure the microwaxe oxen is accurately centered.
I,ine up the center line on the cabinet with the
triangular hole on the front of the bottom duct.
Opening
Screws _"
Triangular Positioning
centerh01e Flange
[_] Drill pilot holes through the positioning flange
and then install four bronze round-head screws
at the front of the bottom duct as shown.
3

mnstaJiation mnstructions
V_ INSTALL THE TOP BRACKET
_ Place t]_e U_p bracket ol_ t]_e u_p of t]_e microwave
ovem_, wit]] die tabs (m die u_p a_d sides o[ tile
bracket fittim_g sqlmre]} agaim_st the m]/iCYov;r_lve
OV e H.
Tabs
Screws
I_sim?g Him_e broHze roHmld-head screws.
V_ INSTALL THE TRIM FRAME
_ Pla('e trim h'ame oxer microwaxe oxen.
the the
_Snap the two s _ring clips on the trim frame into
I,
the slots on the top bracket.
.Slots
•SpringClips
_Open the microwave oven door. Secure the trim
fl'alne using four screws (two round-head screws
on the inside top and two fiat-head screws on the
inside bottom, colored to match yore" trim kit).
Round-headscrews
(color-matchedto yourtrimkit)
Flat-head screws
(color-matched to your trim kit)
Part No. 164D3370P243
Pub. No. 49-40303
[_ REPLACE ANY LOOSE ITEMS
_Yom" trim kit is now flflly installed. Replace any
loose items that were removed h'om the inside
of the microwaxe oxen. Saxe or discard the extra
screws. Do IlOt place thelll iI1 the illicrowa',e o_,ell.
_Keep these installation instructions for flKure
reterellce.
_ Replace house fllse or close circuit breaker to
restore power at the serxice panel.
10-02 JR 4 Printed in Korea