GE TURBOCOOL 23 Safety guide

ge.com
Safety Instructions. ........... 2-4
Operating Instructions
Additional Features ............ 10
Automatic Icemaker ............ 12
Care and Cleaning .......... 14, 15
Crispers and Pans .............. 11
Ice and Water Dispenser ..... 13, 14
Refrigerator Doors .......... 10, 11
Replacing the i,ight Bulbs ....... 16
Shelves and Bins .............. 8, 9
Temperature Controls ........... 5
TurboCool'" .................... 6
Water Filter .................... 7
Installation Instructions
Installing the Refrigerator .... 22-25
Preparing to Install
the Refrigerator ............ 17-19
Removing and
Replacing Doors ............ 19-21
Water Line Installation ....... 26-28
Troubleshooting Tips ....... 30-32
Normal Operating Sounds ....... 29
Consumer Support
Consumer Support ..... Back Cover
Performance Data Sheet ........ 38
Product Registration
(Canadian) ................ 35, 36
Product Registration
(U.S.) ..................... '.43, '.44
State of California Water
Treatment Device Certificate ..... 39
Warranty (Canadian) ........... 40
Warranty (U.S.) ................ 41
Models23and25
C6te fiC6te
Rdfrigdrateurs
La section fran_aise commence a la page 42
Lado a Lado
Refrigeradores
La seccidn en espa_ol empieza en la pagina 76
Write the model and serial numbers here:
#
#
Find these numbers on a label inside
the refrigerator compartment at the
top on the right side. 2001)8074['004 49-60413-1 02-08JR

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
a, WARNING'!
Use this appliance only for its intended purpose as described in this Owner's Manual
SAFETYPRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
This refligerator must be properly installed
and located in accordance with the Inst_fllation
Instructions before it is used.
Do not allow children to climb, stand or hang
on the shelves in the reffigeramI: They could
&mmge the refrigerator and seriously i_jure
themseNes.
{{Do not touch the cold surfaces in the fleezer
compamnent when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
{{Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
In refl_igeramrs wit1 automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating
element locamd on the bottom of the icemake_.
Do not place fingers or hands on the automatic
icemaking mechanism while the refligeramr
is plugged in.
Keep fingers out of the "pinch point" areas;
clearances between the doors and between
the dooIs and cabinet are necessarily small.
Be careflfl closing doors when children are
in the area.
Unplug file refligemmr before cleaning and
making repai,_.
NOTE:Westrong/}/recommendthatan}/servicingbe
performedbyaquafifiedindividual
{{Setting either or both controls to 0FFdoes not
remove power to the light circuit.
{{Do not refleeze flozen foods which have
thawed completel):
2

ge.com .............
DANGER! RISK OFCHILDENTRAPMENt---
PROPERDISPOSALOFTHEREFRIGERATOR
GhiM entrapment and suffbcadon are not problems CFCDisposal
of tile past. Junked or abandoned refligeratoI_ are
still _l)mgerous...even if they will sit for "just a few Your old refl-igerator may have a cooling syst
CFCs
days. If you are getting _q_dof your old refl_igeratoi, that used CFCs (chlorofluorocarbons). ,uc
please follow the instructions below to help prevent believed to harm stratospheric ozone. _}
accidents. If you are throwing away your old refligemto_; make
BeforeYouThrowAway YourOldRefrigerator surethe GFGrefligerantisremovedfor proper
Freezer: disposal by a qualified serviceL If you intentionally _,
or release this CFC refl-igerant, you can be subject to q
• lke off the doors, fines and imprisonment under provisions of
I,eave the shelves in place so that children may enviromnenml legislation. '_'a
not easily climb inside.
USEOFEXTENSIONCORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use
of an extension cord. -_"
However, if you must use an extension cord, it is absolutely necessaD_ that it be a UIAisted (in the United _'
States) or a GSA-listed (in Ganada), _gwire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts. _"
g
g
i
3

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
AWARNING'!
HOWTOCONNECTELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of dlis appliance is equipped
with a 3-prong (grounding) plug which mates
wifll a standard 3-prong (grounding) waU outlet
to minimize the possibilil 0, of electric shock hazard
fiom this appliance.
Have the wall oudet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
If die oudet is a standard 2-prong oudet, it is
your personal responsibility and obligation m
have it replaced with a properly grounded
3-prong waU oudet.
The refligerator should ahvays be plugged into
its own indMdual electrical oudet which has
a voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard flom overheated wires.
Never unplug your refligerator by pulling on
the power cord. Ahvays grip plug firefly and pull
straight out flom the outlet.
Repair or replace immediamly aUpower cords dlat
have become flayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
x_qlen moving the refligerator away flom the
waU, be careflfl not to roll over or damage the
power cord.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS
4

Aboutthe temperaturecontrols, geoom
The temperature controls are preset in the factory at 5for both
the refrigerator and freezer compartments. Allow 24 hours for the
temperature to stabilize to the preset recommended settings.
Several adjustments may be required. Each time you adjust
controls, allow 24 hours for the refrigerator to reach the setting
you have selected.
Setting either or both controls to 0stops cooling in both the freezer
and refrigerator compartments, but does not shut off electrical power
to the refrigerator.
Control settings will vary based on personal preferences, usage and
operating conditions and may require more than one adjustment.
NOTE: The refrigerator is shipped with protective film covering the
temperature controls. If this film was not removed during installation,
remove it now.
PerformanceAir FlowSystem
The Performance Air Flow Sysmm is designed to maximize mmperaulre conuol in file iefligerator and
fleezei compartments. This unique special feaulre consists of the Air Tower along the back waU of the
refligerator and the Air Tunnel on the bottom portion of the fieezer rear wall. Placing food in fiont of the
louvers on these components will not aftbct perfommnce. Although the Air Tower and the Air Tunnel can
be removed, doing so will aft>ct temperature pe_foimance. (Fox removal insuucfions, on-line, contact us at
ge.com o, call 800.GE.(;ARES. In (;anada, contact us at geappliances.ca or call 1.800.561.3344.)
5

About TurboCooLTM (onsome models)
How it Works
TurboCoolral)idly cools file refligermor
compamnent in order m more quickly
cool foods. Use rurboCoolwhenadding a
large amount of food to the refrigerator
compartment, putting away foods after they
have been sitting out at room temperature
or when putdng away warn1 leftovers. It can
also be used if the refligeramr has been
without power for an exmnded period.
Once activamd, the compressor will mrn on
immediately and the fans will cycle on and
off at high speed as needed for eight horns.
The compressor will continue m run until
the reflJgerator compartment cools m
approximately 34°F (1°C), then it will cycle
on and off to maintain this setting. Afker 8
hours, or if rur/JoCoolis pressed again, the
refligeramr compartment will return m
tile original set6ng.
Howto Use
Press TurboCool.The refligemtor
mmpemmre display will show 9(die coldest
setting).
AtXerTurboCooliscomplete, the
refligeramr compartment will return
m the origdnal setting.
NOTES:The refligeramr mmperamre
cannot be changed during
rurboCoot
The fleezer mmperamre is not
affbcmd dining TurboCool.
When opening the refrigerator
door during TurboCootthe f.ns
will continue to run if they have
cycled on.
6

Aboutthe water filter.(onsome models) ge.com
On some models
Water Filter Cartridge
The water filter cartridge is located in the back upper fight
corner of the reflJgerator compartment.
When to Replace the Filter on Models With a
Replacement Indicator Light
There is a replacement indicator light for the water filter
cartridge on the dispenser. This light will utrn orange to roll
you that you need m replace the filmr soon.
The filter cartridge should be replaced when the
replacement indicator light turns red or if the flow of water
to the dispenser or icemaker decreases.
When to Replace the Filter on Models Without a
Replacement Indicator Light
The filter cartridge should be replaced evecy sixmonths
or earlier if the flow ofwamr m the wamr dispenser or
icemaker decreases.
Removing the Filter Cartridge
If you are replacing the cartridge, first remove the old one
by slowly unning it m the left. DOnotpull down on the
cartridge. A small amount of water mW drip down.
Installing the Filter Cartridge
O If you are replacing a SmartWatercartrklge with an
adapter, the adapter illttst be removed before installing
the cartridge. To remove the adapter; turn it to the left
about 1l/4 unn.
If you are replacing a Waterby Cu/figancartridge,
leave the adapter in place. This adapter will stay in the
refligerator when you replace future camidges.
iI ,, r -,
i _ _i i i _ii
With adapter Withoutadapter
(appearance may vary)
O Slowly turn it to the fight until the filter cartridge stops.
DONOTOVERTIGHTEN.As you unn the cartridge, it will
atttomafically raise itself into position. The cartridge will
move about 1/2 turn.
O Run water from the dispenser for 3 minutes (about
1-1/2 gallons) to clear the system and prevent
sputtering.
Press and
FILTERpad
(on some
;) on
RESETWATERFILTER the dispenser
HOLD3SECS lot" ,_ seconds.
NOTE:A newly-installed water filter cartridge may cause
watertosourtfl-o_e_,_,, dispensel_
Filter B! ,,,,,
Youmus _ L_J] ssi:, --_--_ ' relent
_,......... _Filter/.JI ,-." LHter/" _ _ tl.o
n:tc/ _a_ _ _ _ xc. B,,n_ee _ ....
icemake, _uPgass _ irt,, PlYu_g"°° ;:r
bypass pl
SmartWater WaterbyCulligan
On models without a replacement indicator light,
apply the month and ),eat sticker to the new caruidge
to remind you to replace the filter in sixmonths.
Fill the replacement cartridge with water flom the mp
to allow for better flow flom the dispenser immediately
after installation.
OIJne tap the arrow on the cartridge and the cartridge
holder. Place the top of the new cartridge up inside the
holder. Donot push it up into the holder.
To use the filter bypass plug on WaterbyCulliganmodels,
yott IIlttst f]pst remove the filter adapter flom the cartridge
hoMer by unning it to the left.
ffyou have questions--visit our Website
at ge.com,
or call 1.800.GE.CARES 11.800.432.2737).
Replacementfilters:
Toorderadditionalfiltercartridgesin theUnitedStates,
visitourWebsiteatge.com,orcall GEPartsandAccessories,7
t",,a
=4"
==
....7::,_ii,?iiiiil
iiiiiiii_iiiii(iiiiii_i_i'ii
_,,:iiiiLii_i_iii_ii,ii
t{i_iiiitiiii{ii_ii
m
=4"
t",,a
=4"
==
g
,,,=z=,,,
,mla4
,,,w=,|
m
r,,/,3
;:x

Aboutthe shelvesandbins.
Not all features are on all models.
'Refrigerator Door Bins
P
Refrigerator bin
The refligerator door bins are adjusmble.
Toremove:I,iff the fiont of the bin straight
up, then lift up and out.
Toreplaceorrelocate:Engage file back side
of the bin in file molded supports of the
dooL Then push down on the flont of the
bin. Bin will lock in place.
Thesnugger helps prevent tipping, spilling
or sliding of small items stored on the door
shelf. Place a finger on either side of the
snugger near the rear and move it back
and forth m fit your needs.
Deep Door Shelves
Detachable shelf exmnders deepen and
enclose fixed door shelves, providing
more sm_ge room and greater storage
flexibility.
Toremove:I,ift the shelf extender straight
up then pull out.
Toreplace:Engage the shelf extender in the
molded supports on the door and push in.
It will lock in place.
Press tab and pull shelf forward
to remove
Slide-Out Spillproof Shelf
The slide-out spillproof shelf aUows you
m reach imms stored behind others. The
special edges are designed m help prevent
spills flom dripping to lower sheNes.
Toremove:
Slide the shelf out until it reaches the stop,
then press down on the tab and slide the
shelf smdgbt out.
Toreplaceorrelocate:
I,ine the shelf up with the supports and
slide it into place. The shelf can be
reposidoned when the door is at 90 ° or
more. To reposidon the shelf, slide the shelf
past the stops and angle downward. Slide
shelf down m the desired position, line up
with the supports and slide into place.
Makesureyoupushtheshelvesall thewayback
in beforeyoudose thedoor.
8

ge.com
Not all features are on all models.
OuickSpace TM Shelf
This shelf splits in half and slides under
itself for storage of tall items on the shelf
below.
This shelf can be removed and replaced
or relocatedj ust like Slide-.Out Spillproof
Shelves.
On some models, this shelf can not be used
in the lowest position.
Slide-Out Freezer Shelves
Toremove, slide out to the stop position,
lift the fiont past the stop position, and
slide out.
Makesureyoupushtheshelvesall the wayback
in beforeyouclosethedoor.
Fixed Freezer Shelves
Toremove, lift the shelf up at the left side
and then bring the shelf out.
9

Aboutthe additional features.
Not all features are on all models.
ShelfSaver TM Rack
(onsomemodels)
Use this rack to store
beverage cans for easy
access.
It can also hoM a 9" x 13"
baking dish.
Door Can Rack
(onsomemodels)
This door rack holds up
to 9 cans.
NOTE:Thisrackcanonlybe
mountedin thetopposition
underthedairybin.
Removable Beverage Rack
The beverage rock is designed to hold
a bottle on its side. It can be attached
to any slide-.out shel£
Toinstall:
O I,ine up the huge part of the slots on
the top of the rack with the robs under
the shelf.
O Then slide the rack back to lock it
in place.
Aboutthe refrigeratordoors.
Refrigerator Doors
The refligerator doors may feel diffbrent
fllan die ones you are used to. The special
door opening/closing feature makes sure
the doors close all the way and are securely
sealed.
When opening and closing die door you
will notice a stop position. If the door is
opened past this stop point, the door will
remain open m allow you m load and
unload food more easily. When the door
is only partially open, it will automatically
close.
The resistance you feel at the stop
position will be reduced as the door
is loaded with food.
When the door is only partially open,
it will automatically close.
Beyond this stopthe door will
stay open.
10

ge.com
Door Alignment
If (loots are uneven, adjust tile refrigerator
(loot;
O Using a 7/16" wrench, utrn tlle (loot
adjusting screw to the dght to raise the
door; to the left m lower it.
(A nylon plug, imbedded in the
threads of the pin, prevents the pin
from utrning unless a wrench is used.)
0 At_er one or two turns of tile wrench,
open and close the refligerator door
and check the aligmment at the top
of the doors.
Aboutthe crispersandpans.
Not all features are on all models.
l\
Fruit and Vegetable Crispers
Excess water dmt may accumulate in the
bottom of the drawers should be wiped dry.
Adjustable Humidity Crispers
Slide the control all tile way to tlle
H/setting to provide high humidil),
recommended for illost vegetables.
Slide the control all the way to the
LOsetting to provide lower humidity
levels recommended for most fluits.
Aboutcrisperremoval
Not all features are on all models.
Crisper Removal
Crispers can easily be removed by pulling
tlle drawer straight out and lifting tile
drawer tap and over tile stop location.
If die door prevents you flom taking out
the drawers, first try m remove the door
bins. If this does not oflbr enough
clearance, the refligerator will need m
be rolled forward until the door opens
enough to slide the drawet_ out. In some
cases, when you roll the refligeramr out,
you will need m move the refligerator
m the left or right as you roll it out. 11

Aboutthe automaticicemaker.
A newly-installed refrigerator may take 12to 24 hours to begin making ice.
Automatic Icemaker
]cemaker
Switch ]erArm
Ice Drawer
Pull the upper freezer sheff straight
out to access the icemaker. Always
be sure to replace the shelf. The
shelf can be used for storage.
The icemaker will produce seven cubes
per cycle--approximately 100-1,30 cubes
in a 24-hour pedod, depending on fleezer
comparmlent temperature, room
mmperamre, number of door openings
and other use conditions.
If the refligerator is operated before the
water connection is made to the icemake_,
set the power switch in the OFFposition.
_qlen the refligemtor has been connected
to the water suppl}; set the power switch to
the 0N position.
The icemaker will fill wifll water when it
cools to 15°F (-10°C). A newly4nstalled
reflJgemtor m W take 12 m 24 horns m
begin making ice cubes.
Throw away the first few batches of ice
to allow the water line to cleaL
Be sure nothing interferes with the sweep
of the feeler arm.
X_rhenfile bin fills to file level of file feeler
arm, file icemaker will stop producing ice.
It is normal for several cubes m be joined
mgetheL
If ice is not used flequently, old ice cubes
will become cloudy, tasm stole and shrink.
IceDrawer
Ice Storage Drawer
Toaccessice, pull the drawer forward.
Toremovethe drawer, pull it smdght out and
lift it past the stop location.
12

Aboutthe ice and water dispenser.(onsome models) ge.com
On some mode/s
To Use the Dispenser
SpillShelf
Select CUBEDICE_, CRUSHEDICE
or WATER_.
Press the ,glass gently against the top of the
dispenser cradle.
The spill shelf is not self-draining. To
reduce water spotting, the shelf and its
grille shouM be cleaned regularly.
If no wateris dispensedwhentherefrigeratoris
first installed,theremaybe air in thewaterline
system.Pressthedispenserarmforat least two
minutestoremovetrappedair from thewater
line andtofill the watersystem.Toflushout
impuritiesin thewaterline, throwawaythefirst
sixglassfulsof water.
CAUTION:Neverputfingersoranyother
objectsintotheicecrusherdischargeopening.
Locking the Dispenser
@Press the LOCKCONTROL
,__ padfor 3seconds to
lock the dispenser and
control panel. To
:, unlock, press and
HOLD3SEeS hold the pad again
for 3 seconds.
Dispenser Light
This pad turns the night
light in the dispenser on
and off: The light also
comes on when the
LIGHT dispenser cradle is
pressed. If tiffs light
burns out, it should be
replaced with a 6 watt
12 V maximum bulb.
QuickIce
@_rhen you need ice
..... in a hurry, press this
pad to speed lap ice
QUICK ICE
Door Alarm
production. This will
increase ice production
for the following
48 hours or until you
press the pad again.
DOORALARM
To set die alarm, press
tiffs pad until die
indicator light comes
on. This alarm will
sound if either door is
open for more than
3 minums. The light
goes out and the
beeping stops when
you close the dooL
Important Facts About Your Dispenser
Do not add ice flom trays or bags to
the storage draweL It may not crush or
dispense well.
Avoid overfilling glass Mill ice and use
of narrow glasses. Backed-up ice can jam
the chum or cause the door in the chute
m freeze strut. If ice is blocking the
clmm, poke it through with a wooden
spoon.
Beverages and foods should not be
quick-chilled in file ice storage draweL
Cans, bottles or food packages in the
storage drawer may cause the icemaker
or attger to jam.
To keep dispensed ice flom missing
the glass, put the ,glass close to, but not
touching, the dispenser opening.
Some crushed ice may be dispensed even
fllough you selected CUBEDICE.This
happens occasionally when a few cubes
accidentally get direcmd m the cmsheL
AfYer crushed ice is dispensed, some
water may drip flom the clmte.
Sometimes a small mound of snow will
form on fl_e door in d_e ice chute. This
condition is nomml and usually occurs
when you have dispensed crushed ice
repeatedly: The snow Mll eventuMly
evaporate.
13

Aboutthe ice and water dispenser.
Ice Storage Drawer
on Dispenser Models
Toremove:
Set the icemaker power switch to the
OFFposidon. Pull tlle drawer straight out
and then lift past the stop position.
Toreplace:
When replacing the drawe_, be sure to
press it fimdy into place. If it does not go
all the way back, remove it and romm the
drNe mechanism 1/4 turn. Then push
the drawer back again.
Drive
Mechanism
Careand cleaning oftherefrigerator.
i( ¸ : / (J
Dispenser drip area.
Cleaning the Outside
Thedispenserdriparea,(on some models)
beneath file glille, should be wiped dD_.Water
left in this area mW leave deposits. Remove
the deposits by adding undilumd vinegar m
the well. Soak until the deposits disappear
or become loose enough m _Jnse away.
Thedispensercradle(on some models).
Before cleaning, lock file dispenser by
pressing and holding the LOCKCOIVTROt
pad for 3 seconds. Clean with warn1
wamr and baking soda solution--about
a tablespoon (15 ml) of baking soda to
a quart (1 liter) ofwamL Rinse thoroughly
and wipe dxT.
Thedoorhandlesandtrim.Clean with
a cloth dampened with soap}, wateL
Dry with a soft cloth.
Thestainlesssteelpanelsanddoorhandles
(on some models) can be cleaned Mttl a
commercially available stainless steel
cleaner such as Stainless Sted M(_ic'"
Stainless StealM(_ic is available at Ace, True
Value, Servismx; H1_I and other leading
stores. It is also available duougb GE Parts
and Accessories, 800.626.2002. Order part
number _rX] OX] 5.
Do not use appliance wax or polish on the
stainless steel.
Keep the outside clean, gripe Mtb a clean
clod1 lighdy dampened Mill kitchen
appliance wax or mild liquid dish detergent.
DUand polish wkh a clean, soft cloth.
Donotwipetherefrigeratorwith a soileddish
clothor wet towel Thesemayleavea residue
thatcanerodethepaint.Donotusescouring
pads,powderedcleaners,bleachor cleaners
containingbleachbecausetheseproductscan
scratchandweakenthepaintfinish.
14
Cleaning the Inside
Tohelp prevent odors, leave an open box
of baking soda in the flesh food and fleezer
compamnents.
Unplugtherefrigeratorbeforecleaning.If dds
is not practical, wlJng excess moisane out
of sponge or cloth when cleaning around
switches, lights or conuols.
Use warm wamr and baking soda solution--
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) ofwateL Tiffs bodl cleans
and neutralizes odors. Rinse and wipe d_y.
Useofanycleaningsolution otherthanthat
which isrecommended,especiallythosethat
containpetroleumdistillates,can crackor
damagetheinterioroftherefrigerator.
Avoidcleaningcoldglassshelveswith hotwater
becausetheextremetemperaturedifference
maycausethemto break.Handleglassshelves
carefully.Bumpingtemperedglasscancause
it toshatter.
Donotwashany.plasticrefrigeratorparts in
thedishwasher.

ge.com
Behind the Refrigerator
Be careflll when moving file refligemtor
away from file wall. All Wpes of floor
coverings can be damaged, particularly
cushioned coverings and fllose Mtb
embossed stnTaces.
Pull the reflq_gerator straight out and return
it to position by pushing it smdght in.
Moving the reflJgeramr in a side direction
m W result in damage m the floor covering
or refligeratoL
Whenpushingtherefrigeratorback,makesure
youdon't roll overthepowercordor icemaker
supplyline (onsomemodels).
Preparing for Vacation
For long vacations or absences, remove
food and unplug file refligemtoL Clean
the interior with a baking soda solution
of one tablespoon (15 ml) of baking soda
m one quart (1 limr) ofwateL I,eave the
doo,s open.
Set the icemaker power switch to the
OFFposifion and strut off the water supply
to the reflJgeratoL
If die mmperamre can drop below fleezing,
have a qualified servicer drain the wamr
supply system (on some models) m prevent
serious property damage due m flooding.
Preparing to Move
Secure all loose items such as shelves and
drawers by roping them securely in place
to prevent damage.
When using a hand track m move die
reflq_geramI;do not rest file flont or back
of the refligeramr against the hand track.
This could damage the refligeramL Handle
only flom the sides of the refligeramL
Be sure the refrigerator stays in an upright
position during moving.
....Z??ii]ii]
Z?:_IIIIIIIII'II
iiiiiiii_iiiii{iiiiii_i_i_ii
_i'iiiiiLii_i_iii_ii,ii
t{i_iiiitiiii{ii_ii
m
g
m
15

Replacingthe light bulbs.
Setting either or both controls to 0does not remove power to the light circuit.
_ _ Refrigerator Compartment--Upper Light
Pocket
0 Unplug the refligeratoL
0 The bulb is located at file top of file
compartment, inside file dome light
shield. To remove file shield, place your
finger in file pocket at file back of file
shield. Pull file shield forward and down.
After replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the light shield.
Plug the refrigerator back in.
Refrigerator Compartment--Lower Light
This light is located above the top drawer.
O Unplug the refrigeratoL
0 I,ift the light shield up and pull it out.
MYer replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the shield.
Plug the refligerator back in.
Freezer Compartment
0
0Unplug the refl_igeratoL
Remove file shelf just above the light
shield. (The shelfMll be easier m
remove if it is emptied fi_st.) On some
models, a screw at the mp of the light
shield will need m be removed.
@To remove file light shield, press in on
file sides, and lift up and out. On some
models, lift the light shield up and pull
it out.
Replace the bulb with an appliance
bulb of the same or lower wattage,
and reinstall the light shield. When
reinstalling the light shield, make
sure the top robs snap securely
into place. Replace the screw (on
some models).
OReinstall the shelf and plug the
refligerator back in.
Dispenser
0 Unplug the reffigeratoL
O The bulb is located on the
dispenser under the control panel.
Remove the light bulb by turning
it counterclockwise.
0Replace the bulb with a bulb of the
same size and wattage.
Plug the refligerator back in.
16

Installation
Instructions Refrigerator
Models 23 & 25
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT - Savethese
instructions for local inspector's use.
• IMPORTANT - Observeall
governing codes and ordinances.
•Note to Installer- Be sure to leave these
instructions with the Consumer.
•Note to Consumer- Keep these
instructions for future reference.
• Skill level - Installation of this appliance
requires basic mechanical skills.
• Completion time- Refrigerator Installation
30 minutes
Water Line Installation
30 minutes
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation
is not covered under the Warranty.
If the refrigerator has already been installed,
remove the base grille (see Step 2 in Moving
the Refrigerator), then skip to Step 5 in
Installing the Refrigerator.
PREPARATION
WATER SUPPLY TO THE ICEMAKER
If the refrigerator has an icemaker, it will have
to be connected to a cold water line. AGE
water supply kit (containing tubing, shutoff
valve, fittings and instructions) is available
at extra cost from your dealer, by visiting
our Website at ge.com (in Canada at
www.geappliances.ca) or from Parts and
Accessories, 800.626.2002 (in Canada
1.800.661.1616).
TOOLS YOU WILL NEED
3/8" and 5/16" Socket 1/2" and 7/16" Wrench
U
Plastic Putty Knife
Phillips Head Screwdriver
17

Installation Instructions
MOVING THE REFRIGERATOR
ITI LOADING THE RERIGERATOR
ONTO AHAND TRUCK
Leave all tape and door pads on doors
until the refrigerator is in its final location.
To move the refrigerator, use a padded
hand truck. Center the refrigerator on the
hand truck and secure the strap around
the refrigerator. DO NOT OVERTIGHTEN
THE STRAP.
121REMOVE THE BASE GRILLE
Remove the grille by removing the two
Phillips head screws.
If the refrigerator must go through
any entrance that is less than 38"
wide, the doors must be removed.
Proceed to Step 3.
DO NOT remove the handles.
If all entrances are more than
38" wide, skip to Installing
the Refrigerator.
131DISCONNECT THE WATER
COUPLING (on some models)
If the refrigerator has a water dispenser,
there is a water line from the cabinet into
the bottom hinge on the freezer door that
must be disconnected.
To disconnect, push in on the white collar
of the coupling and pull out the tubing.
White collar
Bottom
freezer
hinge
18

Installation Instructions
[_] DISCONNECT THE POWER
COUPLING (on some models)
If the refrigerator has a water dispenser,
there is a power line (harness) from the
cabinet into the bottom hinge on the
freezer door that must be disconnected.
To disconnect, pull apart at the coupling.
[] CLOSE THE FREEZER AND
REFRIGERATOR DOORS
[] DISCONNECT THE ELECTRICAL
CONNECTORS (on some models)
If the refrigerator has a refreshment
center, there are electrical connectors
(harnesses) from the cabinet into the
bottom hinge on the refrigerator door
that must be disconnected.
To disconnect, pull apart each connector.
Bottom
refrigerator
hinge
19
171REMOVE THE FREEZER DOOR
[_] Remove the freezer door top hinge cover
by either squeezing it and pulling it up or
by prying it off with a plastic putty knife.
[]
[]
Remove the two 5/16" hex head screws,
then lift the hinge straight up to free the
hinge pin. 5/16" Hex Head
Open the freezer door to 90.°
90 °

Installation Instructions
MOVING THE REFRIGERATOR (CONT.)
[] REMOVE THE
FREEZER DOOR (cont.)
[] As one person slowly lifts the freezer door
up and off the bottom hinge, the second
person should carefully guide the water
line and power line (harness) through the
bottom hinge.
90°
['_ Set the door on a non-scratching surface
with the inside up.
1-81REMOVE THE
REFRIGERATOR DOOR
[_] Remove the refrigerator door top hinge
cover by either squeezing it and pulling
it up or by prying it off with a plastic
putty knife.
[] REMOVE THE
REFRIGERATOR DOOR (cont.)
[] Remove the two 5/16" hex head screws,
then lift the hinge straight up to free the
hinge pin. 5/16" Hex Head
[_] Open the refrigerator door to 90. °
=
i i
iJ
i
J
90 °
20