GE GCG1700II User manual

Installation
Instructions
15" Built-In Compactors
6C61580 SS
6C61500 BB
6061500 WW
GCG1700I1"
ZC6S150 SS
ZCGP150I1"
*For ZCGP150II and 6C61700 II,
also refer to the instructions
provided on the template packed
with those models.

Safety information
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
•IMPORTANT- Save these instructions for
local inspector's use.
•IMPORTANT- Observe all governing codes
and ordinances.
Note to Installer - Be sure to leave these
instructions with the Consumer.
•Note to Consumer- Keep these instructions with
your Owner's Manual for future reference.
•Skill Level- Installation of this appliance requires
basic mechanical and electrical skills.
•Completion time - 1 hour.
•Proper installation isthe responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty. See Owner's Manual
for warranty information.
iMPORTANT
•Use this compactor only for its intended purpose.
•This compactor is designed for BUILT-IN
installations ONLY.
WARNING!
Do not allow items to fall or collect behind
the compactor. Failure to follow this
instruction could result in a fire.
CAUTION:
For personal safety, remove house fuse or
oven circuit breaker before beginning
installation to avoid severe or fatal
shock injury.
CONTENTS
Design Information
Models Available ..............................................................3
Product Dimensions and Clearances ............................3
Tools Required ..................................................................3
Parts Supplied ..................................................................3
Advance Planning
Clearances ........................................................................4
Models with a Custom Drawer Panel ..........................4
Installation Preparation
Electrical Requirements ................................................5
Grounding Requirements ................................................5
Unpacking the Compactor ..............................................6
Leveling the Compactor ..................................................7
Adjusting the Retaining Bracket ....................................7
Adjusting the Base Toekick ............................................7
Installation Instructions
Position the Compactor under the Countertop ............8
Attach the Compactor to the Countertop ....................8
Reinstall the Compactor Drawer ....................................9
Installation of the Trash Bag Caddy ..............................9
Finalize Installation ..........................................................9
2

Design information
MODELS AVAILABLE
GCG1580SS
GCG1500BB
GCG1500WW
GCG1700I1"
ZCGS150SS
ZCGP150I1"
*For ZCGP150II and GCG1700II, also refer
to the instructions provided on the template
packed with those models.
PRODUCT DIMENSIONS AND CLEARANCES
24" (61cm)
min 15-1/8"
(38.4cm)
min 34" (86.4cm)
to
35" !88.9 cm)
Locate the outlet 18" (45.7 cm) rain
from the floor, 3" (7.6 cm}rain from
either side
23" (58.4 cm)
33-3/4"
(85.8cm)
min.
to
35" (88.9 cm)
max.
• Allow 23" (58.4 cm)
clearance atthe front for
a full drawer opening,
• Allow 6"(15.2 cm)
clearance on the right
side to the nearest
vertical wall or cabinet
for bag removal.
• Nete: This compactor is
designed for built-in
applications only.
TOOLS REQUIRED
.Level
•Phillips Screwdriver
• Pliers
•Gloves
• Measuring Tape
PARTS SUPPLIED
•6 mounting screws (located in the literature package)
•2 countertop retaining brackets
•2 side mounting clips
3

ADVANCE PLANNING
CLEARANCES
You should be able to fully open the compactor
drawer. Six inches (15.2 cm)is required on the right
side of the compactor for bag removal.
• Allow 23 inches (58.4 cm) in front of the compactor
to remove the drawer.
This compactor is designed as a built-in
appliance only. It may be located in any
convenient space under a countertop.
DO NOT OPERATEFREE-STANDING.
The compactor may be installed beneath
countertops of stone or other materials that will
not accept screws. No trim kit is required.
The compactor must be securely installed in a cabinet
that is firmly attached to the house structure. Weight
on the compactor drawer could cause the compactor
to tip and result in injury. Never allow anyone to
climb, sit or hang on the compactor drawer.
MODELS WiTH A CUSTOM
DRAWER PANEL
Models ZCGP150 II and GCG1700 II
The custom drawer panel and custom handle of your
choice should be secured to the compactor before
installation begins. A template with instructions and
installation hardware is provided with those models.
For planning purposes, you may order the template in
advance. Order Pub. No. 31-30597. Complete panel
installation instructions are included on the template.
CUSTOM PANELSiZE REQUIREMENTS:
Maximum panel weight is 12 LBS (5.4 kg).
3/4"
(1.9 cm)
Thick
Custom 29-5/16"
Panel (74.5 cm)
_ 14-7/8"
(37.8 cm)
4

Installation Preparation
ELECTRICAL REQUIREMENTS
WARNING!
FORPERSONAL SAFETY: Remove house
fuse or open circuit breaker before
beginning installation. Do not use an
extension cord or adapter plug with
this appliance.
• The power supply cord and plug should be brought
to a separate 15 or 20 ampere branch circuit single
grounded receptacle. The outlet box should be
located within reach of the 36" (91.4 cm) power cord.
*This appliance must be supplied with 120V,60Hz
and connected to an individual properly grounded
branch circuit, protected by a 15or 20 ampere
circuit breaker or time delay fuse.
• If the electrical supply does not meetthe above
requirements, call a licensed electrician before
proceeding.
iMPORTANT: Observe all governing codes and
ordinances.
GROUNDING REQUIREMENTS
WARNING!
The improper connection of the equipment
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service representative if you
are in doubtthatthe appliance is properly
grounded.
• Electrical Ground is REQUIREDon this compactor.
• DO NOT ground to a gas pipe.
• DO NOT change the power supply cord plug. If it
does not fit the outlet, have a proper outlet installed
by a qualified electrician.
• DO NOT have a fuse in the neutral or grounding
circuit. Afuse in the neutral or grounding circuit
could result in an electrical shock.
• DO NOT use an extension cord with this compactor.
Failure to follow these instructions could result in
death or serious injury.
Recommended Grounding Method:
Foryour personal safety,this appliance must be grounded.
This appliance is equipped with a power supply cord having
a 3-prong grounding plug. Tominimize possible shock
hazard,the cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in accordance
with the National Electrical CodeANSI/NFPA70--1atest
edition* and all local codes and ordinances. If a mating wall
receptacle is not available, it is the personal responsibility
and obligation of the customer to have a properly grounded
3-prong wall receptacle installed bya qualified electrician.
3-prong grounding-type
wall receptacle
3-prong _--...._
grounding I
plug . I (| I_ I
ower'I
supply _.4_'_J' Groundin_
cord 71 plug
Copies of the standards
listed may be obtained from:
* National Fire
Protection Association
Batterymarch Park,
Quincy, MA 02260
5

Installation Preparation
UNPACKING THE COMPACTOR
•Move the compactor close to the installation
location.
• Use a section of the shipping carton to protectthe
finished floor.
• Do not use the handle to lift the compactor.
• Remove all protective packaging materials such as
tape or shipping pads. Remove waxy residue caused
by shipping material with a mild solution of liquid
household cleaner and water.
• Check thatthe power supply cord is attached to the
cord clip on the rear of the compactor.
_ Cord cli_
IMPORTANT: Use the shipping carton as a pad.
Do not slide the compactor across a finished floor.
Damage will occur.
UNPACKING THE COMPACTOR
(CONT.)
• Open the compactor drawer and remove any
shipping materials or other items shipped in the
drawer.
• Do not remove the compactor bag (if installed).
•Grasp the sides of the drawer and lift it out of the
compactor. Place the drawer on a protected surface.
The drawer can scratch a finished floor.

Installation Preparation
[_ LEVELING THE COMPACTOR
•The top of the compactor should be at least 1/8"
(3 ram) from the top of the cabinet opening. You can
adjust the height of the compactor by turning the
screws on the front leveling legs and rear wheels.
Front leveling legs
_els
• Place a level inside the compactor on the floor
of the cabinet.
J
/
• Use the leveling legs to adjust level front to back and
side to side.
I_ ADJUST THE RETAINING
BRACKET
Determine installation depth of the compactor
beneath the countertop,
Adjust the position of the retaining brackets so that
the screws can meet the underside of the
countertop.
Mounting clips are provided for stone or other hard
countertops that will not accept screws.
Retaining
bracket
Countertop
I_ ADJUSTING THE BASE TOEKICK
Atoekick extension is supplied. It can be used to cover
any gaps from the bottom of the compactor to the floor,
• Remove the top toekick screws as shown. Lift off top
toekick piece.
• Loosen the base toekick screws, adjust to touch the
floor and tighten the screws.
• Reinstall the top toekick piece with the original
screws.
/
Top toekick Loosen screw
Adjustable on each side
lower toekick

Installation
I_ POSITION COMPACTOR UNDER
THE COUNTERTOP
WARNING!
When moving the compactor, use gloves to
protect and cushion your hands.
To protect the finished flooring, use a dolly
to move the compactor near the installation
location.
Failure to follow these instructions could
result in injury.
• Plug the power cord into a properly grounded
receptacle.
• Carefully lift the front of the compactor slightly and
roll the unit into the cabinet opening until the
retaining brackets stop.
Lift here
I_ ATTACH THE COMPACTOR TO
THE COUNTERTOP
• Use two #8-18 x 1/2" (45.7 cm x 1.3 cm) mounting
screws to fasten the retaining brackets at the top
of the compactor to the underside of the countertop.
Retaining
bracket
_'_r--,,,, Mounting
screws
• If the brackets cannot be attached to the underside
of the countertop, attach mounting clips to the
bracket. Fasten the compactor to the cabinet front
with mounting screws through the mounting clips.
ig
bracket
Mounting
screw
Mounting
clip
8

Installation
[_ REINSTALL THE COMPACTOR
DRAWER
• Grasp the sides of the drawer. Carefully slide the
drawer into the compactor.
iiiii
_] INSTALLATION OF THE TRASH
BAG CADDY (on some models)
• Set the bag caddy into the drawer and hook the
pre-punched holes in the caddy on the drawer
buttons.
• Setthe trash bag into the bag caddy and fold over.
• Hook the holes in the bag over the drawer buttons.
Trash
Drawer
buttons
_9qFINALIZE THE INSTALLATION
• Turn power on atthe source.
• Refer to your Owner's Manual for operating
instructions.
9

Notes
10

Notes
11

NOTE:While performing installations described in this book,
safety glasses or goggles should be worn.
NOTE:P]-odtlcr ilnpvovelnent is a continuil_g Lql(](_aVOl" at
General Electri(. Thel-etk_re, lnatevials, _ll_pem-al_ce mid
specifi(ations _11-(_ sul_je(r to (hmlge without nori(e.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY40225
ge.com Pub.No.31-30596
206C1559P140
08-05JR
Printedin China