GE 24922 - Universal Remote Control User manual

Universal Remote
Instruction Manual
Control Remoto Universal
Manual de Instrucciones
24922
6177

2
Introduction
Congratulations on your purchase of the GE Universal
Remote Control. The GE Universal Remote Control is
one of the most easy to use remote controls available
today. With the GE Universal Remote Control, juggling
multiple remote controls is a thing of the past!
Your GE Universal Remote Control controls multiple
devices, including the most popular brands of TV,
DVR, DVD, CBL, and SAT. The GE Universal Remote
Control is easy to use, easy to program, and it gives
you total control — at the touch of your fingertips!
IMPORTANT: SAVE THIS MANUAL AND CODE LIST
FOR FUTURE REFERENCE
Introduction..................................................................................... 2
Setup .................................................................................................. 3
Battery Installation............................................................... 3
Battery Precautions.............................................................. 3
Battery Saver........................................................................... 3
Code Saver ............................................................................... 3
Button Functions .......................................................................... 4
Programming Your Remote..................................................... 6
Direct Code Entry................................................................... 6
Auto Code Search ................................................................. 8
Controlling Combo Devices.............................................. 9
Favorite Function ................................................................10
Using Your Remote ....................................................................11
Master Volume Feature....................................................11
Code Identification .............................................................12
Reset to Factory Settings.................................................12
Using Shift...............................................................................13
Troubleshooting..........................................................................14
Warranty ........................................................................................15
Table of Contents
Scan this to view remote
setup video
Mira a ver el video de
instalación remota
http://www.jascoproducts.com/remote

3
Your universal remote requires two (2) AAA batteries
(not included). Alkaline batteries are recommended.
Battery Installation
1. On the back of the remote, slide the cover down to
remove.
2. Match the (+) and (-) marks on the batteries to the
(+) and (-) marks inside the battery compartment,
then insert two (2) AAA batteries. Be sure to use
fresh batteries.
3. Slide the battery cover back into place.
NOTE: If your remote stops operating properly,
replace the batteries with new ones. The remote will
retain the codes you have programmed for up to 10
minutes after the batteries are removed.
Battery Precautions
• Donotmixoldandnewbatteries.
• Donotmixalkaline,standard(carbon-zinc),or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Alwaysremoveold,weakorworn-outbatteries
promptly and recycle or dispose of them in
accordance with local and national regulations.
Battery Saver
Your remote automatically turns off if the buttons are
depressed more than 8 seconds. This will save your
batteries should your remote get stuck in a place
where the buttons remain depressed (e.g., between
the sofa cushions).
Code Saver
You will have up to 10 minutes to change the
batteries in your remote without losing codes you
have programmed. However, do not press any
buttons until batteries are installed in the remote. If
buttons are pressed without batteries in the remote,
all codes will be lost.
Setup

4
LAST Returns to
the previously
selected channel.
EXIT ExitsOn-Screen
Menus and/or
Returns to previous
On-Screen selection.
DOT: Used to select
digital channels, e.g., 2.3.
VOLUME UP/DOWN
Changes the volume
level of the device,
normally the TV.
CHANNEL UP/DOWN
Changes the channels.
RECORD, PLAY, STOP,
REW, FF, PAUSE
TV, DVR, CBL, B-RAY,
AMP, AUX
Selects device
to control.
Red Indicator lights when
any button is pressed.
INPUT Selects the video
inputs from available
viewing sources.
Button Functions
UP, DOWN, LEFT & RIGHT
Navigation buttons.
GUIDE Displays satellite
or cable on-screen.
DVR LIST Displays list of
recorded programs

5
A, B, C, D
Colored ABCD buttons for
menu navigation in DVRs
andsettopboxes
INFO Displays/selects
on-screen channel
information.
MENU Displays the
Menu on the TV.
SETUP Button is used to
program the remote
SHIFT is the alternate
function of this button.
Use the SHIFT button to
access the menu and DVR
list of your device. To enter
the SHIFT mode press
thisbuttononce.Toexit
the shift mode, press the
SHIFT button again.
MUTE Turns off the
TV sound while the
picture remains.
OK Selects menu
items for the device
you are controlling.
NUMBERS
Enter numbers for direct
channel selection. Some
devices require ENTER
to be pressed after
channel selection.
Button Functions, cont.
ON•OFF Turns
devices On or Off.
Fav Allows user to
program up to 10 of
their favorite channels
for quick

6
Programming Your Remote
Your GE universal remote control is designed to
control multiple audio/video devices such as a TV,
DVD, DVR, satellite, cable and audio device using
only one remote. To use this remote, you will need to
program it to control the devices of your choice. There
are two ways to program the remote - direct code
entry or auto code search.
Direct Code Entry (Recommended)
1. Locate the Remote Code List provided
in this manual. Find the DEVICE
CATEGORY you wish to program (for
exampleTV, DVR, CBL, B-RAY, AMP,
AUX) and then find the BRAND of that
device. Circle all the codes under that
brand.Example:ForaGETV,locatethe
TV code section then circle all of the
GE TV codes.
2. Manually turn on the device you wish
to control.
3. Press and hold the SETUP button
until the red indicator light stays on
(approximately2seconds)andthen
release the SETUP button.
4. Press and release the device button on
the remote (TV, DVR, CBL, B-RAY, AMP,
AUX). The red indicator will blink once
and then remain on.
5. Enter the first 4-digit code previously
found in the code list using the
number buttons on the remote. If the
code entered is a valid code, the red
indicator light will turn off. If the code
entered is not a valid code, the red
indicator light will flash and remain on
allowing you to re-enter the code.
Note: If no buttons are pressed for 35
seconds, the remote will exit the SETUP
mode and you will have to start over.

7
Programming Your Remote, cont.
6. Point the remote at the device. Press
the POWER button—if the device
turns off, no further programming is
required for that device. If the device
does not turn off, return to steps 3-5
andusethenextcodefoundinthe
code list. Continue this process until a
code for your device is found.
7. Repeat this process for each device
(forexampleTV,DVR,CBL,DVD,SAT,
AUX) in your home entertainment
system you wish to control.
Programming Notes
• Ifyourdevicedoesnotrespondtotheremoteafter
trying all codes listed or your brand is not listed in
the code list, use the Auto Code Search method to
program your remote.
• Sometimestherstcodethat“works”withyour
device may operate only a few functions of your
device. There may be another code in the code
list that performs more functions. Try other codes
from the code list for more functionality.
• WiththeDirectCodeEntrymethod,youcan
program any device button to control any device
in your home entertainment system.
Forexample,youcanusetheDVR device button
to control an audio receiver or a DVD, VCR, satellite
device, etc.
• Forcombinationdevices,youmayhavetoentera
codeforeachdevice.Forexample,foraVCR/DVD
device, you may have to enter a code for the DVD
under the DVD button and enter a code for the
VCR using a different device button on the remote.
• Writedownthecodefoundtooperateyourdevice
for future reference.

8
Programming Your Remote, cont.
Auto Code Search
The Auto Code Search, searches automatically
through all of the codes stored in this remote. Read
all the following steps prior to starting the auto code
search as you will need to be prepared to lock-in the
proper code when found.
1. Manually turn on the device you wish
to control.
2. Press and hold the SETUP button
until the red indicator light stays on
(approximately2seconds)andthen
release the button.
3. Press and release the device button on
the remote (TV, DVR, CBL, B-RAY, AMP,
AUX) for device you wish to control.
The red indicator will blink once and
then remain on.
4. Point the remote at the device and
press and release the POWER button
(for TV) or PLAY button (for DVD, VCR,
etc.) to start the search. The red
indicatorwillash(approximately
every 2 seconds) as the remote
searches. Note: The remote must be
pointed at the device for the duration
of this search.
5. Place your finger on the #1 button so
you are prepared to lock-in the code.
6. When the device shuts off or begins
playing, press the #1 button to lock-in
the code. The red indicator light will
turn off. Note: You have approximately
two seconds after the device shuts off
or begins playing to lock-in the code.
7. Point the remote at the device and
check to see if the remote operates the
device as desired. If it does, no further
programming is required for that
device. If it does not, return to step 2
and start the auto code
search again.

9
Programming Your Remote, cont.
8. Repeatthisprocessforeachdevice(forexample
TV, DVD, SAT, AUX) in your home entertainment
system you wish to control.
Programming Notes
• Thisprocessmaytakeseveralminutesasthe
remote contains many codes.
• WhenusingtheAutoCodeSearchprogramming
method, the device button corresponding to
the type of device you want to control must be
selected(forexample,theTV device button must
be selected in step 3 if you want to control a TV,
the DVD device button for a DVD player, etc.)
• TheSETUP button can be used during the search
process to reverse the direction of the search of
theremotecodes.Forexample,ifyoumissthe
code for your device and the remote is continuing
to search (as indicated by the blinking red light),
press the SETUP button and the code search will
reverse direction and return to the code.
• Sometimestherstcodethat“works”withyour
device may operate only a few functions of your
device. There may be another code in the code
list that performs more functions. Continue the
auto code search as directed above until the best
code is found.
Controlling Combo Devices
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device.
Forexample,ifyouhaveaTV/DVDCombo,youmight
need to set up one code under the TV button to
control the TV part AND a separate code (under any
other Mode button) to control the DVD part.

10
Favorite Function
Allows user to program up to 10 of their favorite
channels for quick access.
Setup Favorite Function
1. Press and release the device button
(TV, DVR,CBL, B-RAY, AMP, AUX). The
indicator light will blink once. Special
 Note:Usermustselectthedevice
type that controls the channels; for
 exampleifauserhasaCableBox
for controlling channels, then this
device button must be selected to
properly change the channels on
 thecablebox.
2. Press and hold the SETUP button for 2
seconds or until the red indicator light
turns on, then release the SETUP button.
3. Press and release the FAV button.
The red indicator will blink once
and remain on.
4. Press and release the numerical button
(0 – 9) that you will use for storing your
favorite channel. The red indicator will
blink once and remain on.
5. Enter the channel number you wish
 toprogram,forexamplechannel4,
21, 4-1, 52-2.
6. Press and release the FAV button, the
red indicator will turn off. Your
favorite channel is now saved.
7. Process can be repeated for up to 10 of
your favorite channels.
Using Favorite Function
1. Press and release the FAV button. The
red indicator light will turn on.
2. Press and release the programmed
button (0-9). The red indicator will
blink twice and the remote will
send the code for your
pre-programmed channel.
Programming Your Remote

11
Using Your Remote
Master Volume Feature
The Master Volume Feature allows you to select a
single device (TV or audio receiver) that the volume
controlalwayscontrols.Forexample,theremotecan
be in TV mode while the volume buttons control the
volume on your audio receiver instead of your TV.
Enabling the Master Volume Feature
1. Press and hold the SETUP button
until the red indicator stays on
(approximately2seconds)andthen
release the button.
2. Press and release desired device
button (TV, DVR, CBL, B-RAY, AMP,
AUX) for the device you wish to setup
to always control the volume.
3. Press and release the MUTE button.
4. Press and release the VOL + button.
The red indicator will blink twice and
then go off.
To test the feature put the remote in
another mode such as the TV mode if
you programmed the audio receiver to
be the Master Volume Device. Point the
remote at the audio receiver, press and
hold either the VOL - or the VOL + button.
If the audio receiver volume changes then
the remote is programmed correctly. If
the TV volume changes and not the audio
receiver, you will have to repeat the steps
above and test again.
Disabling the Master Volume Feature
1. Press and hold the SETUP button
until the red indicator stays on
(approximately2seconds)andthen
release the button.
2. Press and release the device button
(TV, DVR, CBL, B-RAY, AMP, AUX) which
is programmed to control the Master
Volume Feature.

12
Using Your Remote, cont.
3. Press and release the MUTE button.
4. Press and release the VOL - button.
The red indicator light will blink twice
and go off.
Code Identification
1. Press and hold the SETUP button
until the red indicator stays on
(approximately2seconds)andthen
release the button.
2. Press and release the desired device
button (TV, DVR, CBL, B-RAY, AMP,
AUX) you would like the code for.
3. Press and release ENTER button.
4. Press and release the #1 button.
Count the number of times the
remote light flashes. This is the
number corresponding to the first
digit of the code. Repeat the process
by pressing the #2, #3 and #4
buttons for the remaining digits.
5. Press and release ENTER button to
exitthismode.
Reset to Factory Settings
1. Press and hold the SETUP button
until the red indicator stays on
(approximately2seconds)andthen
release the button.
2. Press and release the MUTE button.
3. Press and release the number #0
button. The red indicator light will
flash twice.

13
Using Your Remote
Using SHIFT for Menu and Navigation
The SHIFT button allows access to more than one
functionforcertainbuttons.Note:theredindicator
light will blink in shift mode.
Use the SHIFT/SETUP button prior to accessing the
DVR LIST, MENU, EXIT forexample:
For DVR List press and release SHIFT/
SETUP then DVR LIST/GUIDE.
For Menu, press and release SHIFT/SETUP
then INFO/MENU.
ForExit,pressandreleaseSHIFT/SETUP
then LAST/EXIT.
SPECIAL NOTE: Remote will stay in shift mode until
the SHIFT button is pressed again, or until 10 seconds
of inactivity.

14
Remote does not operate your device.
• Pressthedevicebuttonofthedeviceyou
wish to control.
• Programtheremotewithanewcode.
• Installnewbatteries.(Youmighthaveto
reprogram your remote after installing
new batteries.)
• Remotemaynotbecompatiblewithyourdevice.
Remote does not operate some features of
your device.
• Sometimesaparticularcodemightoperatesome
features but not all. Try programing remote with a
new code.
• Remotemaynotbeabletooperateallfeaturesof
your device or button names might be different
than that of your original remote.
Red Indicator blinks and stays on after you
program a product code.
• Remotedidnotacceptthecode.
• Trytoprogramthecodeagainortry
a different code.
Remote Code is not available for a combo device
(e.g. TV/VCR)
• Seesectionforcontrollingcombodevices.
If you have any questions or would like
additional information please visit our web site
www.jascoproducts.com, or contact our
Technical Support Group at 1-800-654-8483.
Troubleshooting

15
Jasco Products Company warrants this product to be
free from manufacturing defects for a period of 90
days from the original date of consumer purchase.
This warranty is limited to the repair or replacement
ofthisproductonlyanddoesnotextendto
consequential or incidental damage to other products
that may be used with this unit. This warranty is in
lieuofallotherwarrantiesexpressorimplied.Some
states do not allow limitations on how long an implied
warrantylastsorpermittheexclusionorlimitationof
incidental or consequential damages, so the above
limitations may not apply to you. This warranty gives
you specific rights, and you may also have other
rights which vary from state to state. If unit should
prove defective within the warranty period, return
prepaidwithdatedproofofpurchaseto:
Made in China
Jasco Products Company
10 East Memorial Road
Oklahoma City, OK 73114
www.jascoproducts.com
90-Day Limited Warranty

16
This device complies with part 15 of the FCC rules.
Operationissubjecttothefollowingtwoconditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
FCCNOTE:Themanufacturerisnotresponsiblefor
anyradioorTVinterferencecausedbyunauthorized
modifications to this equipment. Such modifications
could void the user’s authority to operate the
equipment.
NOTE:Thisequipmenthasbeentestedandfound
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encourage to try to correct
the interference by one or more of the following
measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipment
and receiver.
•Connecttheequipmentintoanoutletonacircuit
different from that to which the receiver
is connected.
•Consultthedealeroranexperiencedradio/TV
technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme
á la norme NMB-003 du Canada
FCC Statement

17
Introducción
Felicitaciones por adquirir el control remoto universal
GE. El control remoto universal GE es uno de los más
fáciles de usar hoy en día. Con el control remoto
universal GE, ¡el uso de varios controles remotos es
cosa del pasado! Su control remoto universal GE
controla varios dispositivos, incluidas las marcas más
populares de televisores, DVR, DVD, cable y satélite. El
control remoto universal GE es fácil de usar, fácil de
programaryledacontroltotal:¡conelsimpletoque
de sus dedos!
IMPORTANTE: GUARDE ESTE MANUAL Y LA LISTA DE
CÓDIGOS PARA CONSULTARLOS EN EL FUTURO
Introducción..................................................................................17
Configuración...............................................................................18
Para Instalar las Pilas........................................................18
Precauciones con las Pilas..............................................18
Ahorrador de Pilas ..............................................................18
Protección de Ahorros.......................................................18
Funciones de los Botones ...............................................19
Programación de su Control Remoto ...............................21
Entrada Directa de Códigos ...........................................21
Búsqueda Automática de Códigos .............................23
Control de Aparatos Combinados...............................24
Función Favoritos................................................................25
Uso de su Control Remoto ....................................................26
Función de Volumen Principal .....................................26
Identificación de Códigos................................................27
Para Restablecer las Configuraciones
Predeterminadas.................................................................27
El uso de SHIFT.....................................................................28
Solución de Problemas ...........................................................29
Garantía..........................................................................................30
Declaración de la FCC..............................................................31
Índice

18
Su control remoto universal necesita dos (2) pilas tamaño
AAA (no se incluyen). Se recomiendan pilas alcalinas.
Para Instalar las Pilas
1. Presione la pestaña y levante la tapa en la parte
posterior del control remoto.
2. Inserte dos (2) pilas tamaño AAA, de manera que las
marcas (+) y (-) de las pilas coincidan con las marcas
(+) y (-) en el interior del compartimiento de las pilas.
Asegúrese de usar pilas nuevas.
3. Presione la tapa del compartimiento de las pilas en
su lugar.
NOTA: Si su control remoto deja de funcionar
correctamente, reemplace las pilas por otras nuevas. El
control remoto conservará los códigos que ha programado
durante un máximo de 10 minutos después de retirar las
pilas.
Precauciones con las Pilas
• Nousepilasnuevasconpilasusadas.
• Nousepilasalcalinasconpilasestándar(carbono-zinc)
o con pilas recargables (Ni-Cd, Ni-MH, etc.).
• Siemprequitelasbateríasviejas,débilesodescargadas
con prontitud y recíclelas o deséchelas de acuerdo con
las regulaciones locales y nacionales.
Ahorrador de Pilas
Su control remoto se apaga automáticamente si los
botones se presionan durante más de 8 segundos. Esto le
ahorrará las pilas si el control remoto se permanece en un
lugar donde los botones quedan presionados (por ejemplo,
entre los cojines del sofá).
Protección de Ahorros
Usted tendrá hasta 10 minutos para cambiar las pilas
del control remoto sin perder los códigos que haya
programado. Sin embargo, no presione ningún botón hasta
que haya instalado las pilas nuevas en el control remoto.
Si presiona los botones sin haber instalado las pilas en el
control remoto, se perderán todos los códigos.
Configuración

19
Funciones de los Botones
LAST Regresa al
canal previamente
seleccionado o botón
de repetición de DVD.
EXIT Sale de los menús
en pantalla y/o regresa
a la selección anterior
en pantalla.
DOT:Seutilizapara
seleccionar los canales
digitales,porejemplo:2.3.
VOLUME ARRIBA/ABAJO
Cambia el nivel de volumen
del producto, normalmente
el del televisor.
CHANNEL ARRIBA/ABAJO
Cambia los canales.
RECORD, PLAY, STOP,
REW, FF, PAUSE
TV, DVR, CBL, B-RAY
AMP, AUX
Selecciona el dispositivo
que se va a controlar.
El indicador rojo se ilumina
cuando se presiona
cualquier botón.
INPUT Selecciona las
entradas de video de las
fuentesdevisualización
disponibles.
ARRIBA, ABAJO,
IZQUIERDA y DERECHA
Botones de navegación.
GUIDE Visualizaen
pantalla la guía de
programas de satélite o
cable.

20
Funciones de los Botones, continuación
A, B, C, D
Color de botones de ABCD
para el menú de navegación
en DVR y receptors
INFO Muestra/
selecciona la
información del canal
en pantalla.
MENU para mostrar el
menú en el televisor.
SETUPSeutilizapara
configurar el control
remoto y para la función de
búsqueda de códigos.
MUTE Apaga el
sonido del televisor
mientras que la
imagen continúa.
OK Selecciona los
elementos del menú
para el dispositivo que
está controlando
ENTER después de la
selección del
NÚMEROS
Introduzcanúmeros
para la selección directa
de canales. Algunos
dispositivos necesitan
que se presione ENTER
después de la selección del
canal.
ON•OFF Enciende y
apaga dispositivos.
Fav Le permite al
usuario programar
hasta 10 de sus
canales favoritos para
un acceso rápido