GE Monogram ZKD910 User manual

GE Monogram®
Warming
Drawer
Installation
Instructions
27" Wide Models:
ZKD910
30" Wide Models:
ZTD910

2
Before you begin — Read these instructions completely and carefully.
IMPORTANT - Save these instructions for local inspector’s use.
IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer - Be sure to leave these instructions with the Consumer.
Note to Consumer - Keep these instructions with your Use and Care Book for future reference.
This appliance must be properly grounded. See “Electrical Supply”, page 4.
CAUTION
WARNING
If you have a question concerning the installa-
tion of this product, call the GE Answer
Center®Consumer Information Service at
800.626.2000, 24 hours a day, 7 days a week.
If you received a damaged warming drawer,
you should immediately contact your dealer or
builder.
Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See the Use & Care
Guide for warranty information.
•Use this appliance only for its intended
purpose.
Check with local utilities for electrical codes
that apply in your area. Local codes vary.
Installation electrical connections and
grounding must comply with applicable codes.
In the absence of local codes, the drawer
should be installed in accordance with
National Electrical Code ANSI/NFPA 70-1990
or latest edition.
Contents Design Information
Models Available.................................................................................................................................. 3
Product Dimensions............................................................................................................................ 3
Accessories ........................................................................................................................................... 3
Tools and Materials Required ............................................................................................................ 3
Installation Preparation
Advance Planning ............................................................................................................................... 4
Grounding the Appliance................................................................................................................... 4
Remove the Packaging and Parts ....................................................................................................... 5
Installation Below a Countertop ........................................................................................................ 5
Installation Below Wall Ovens ............................................................................................................ 6
Installation
Step 1: Provide Cabinet Support and Anti-Tip Bracket ................................................................... 7
Step 2: Install Warming Drawer ......................................................................................................... 7
Accessories
ZXD27B, ZXD30B for Installation of a Custom Panel ..................................................................... 8
JXPN1 Pan Kit ................................................................................................................................... 10
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada, call
1-888-880-3030.
For Monogram Parts and Accessories, call
1-800-626-2002.
ANTI-TIP PRECAUTIONS
An anti-tip brace must be installed to
prevent the drawer from tipping forward
when opened and loaded.
Failure to do so could result in personal
injury.
WARNING

3
Design Information
Warming Drawer
Models
Available
ZTD910
30” Wide model
ZKD910
27” Wide model
Product
Dimensions
Dimension A
ZTD910 30”
ZKD910 26-3/4”
The warming drawers may be installed
directly into a wall or wall oven cabinetry,
or below a countertop.
Accessories ZXD27B, ZXD30B – This kit provides for the
installation of a custom front panel on 27”
and 30" wide models.
Note: The original drawer front and handle will be removed and
discarded when this kit is used. A custom handle (not supplied)
must be installed to complete the installation.
Tools and
Materials
Required
• Wood screws and adhesive or other hardware for installing
runners or shelf to support warmer drawer.
• 2 x 4 or 2 x 2 lumber for runners
• 2 x 4 or 2 x 2 wood block for anti-tip security
• Saw
• Level
• Drill and 1/16” bit
• Phillips screwdriver
Runners must be level, rigidly mounted and capable of supporting
150 pounds.
26"
Including
Handle
23-1/4"
A
10-1/2"
9"
1"
Drawer
Open
27"
JXPN1 – Warming drawer pan kit. This kit
includes supports and a set of 5 pans which fit
into 27" and 30" models.

4
Design Information
Warming Drawer
Advance
Planning
•The drawer may be installed below a
countertop, a cooktop, a single or double
oven and side by side using 2 drawers.
•The warming drawer can be installed below
approved cooktops. Allow 2" min. clearance
from bottom of cooktop burner box to top
of warming drawer cutout. See page 5.
•The warming drawer can be installed below
approved ovens. Allow a 2" min. clearance
between cutouts. Additional clearances may
be required. See page 6.
IMPORTANT - (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
Do not use an extension cord or adapter plug
with this appliance. Follow National electrical
codes or prevailing local codes and ordi-
nances.
This warming drawer must be supplied with
120V, 60Hz, and connected to an individual,
properly grounded branch circuit, and
protected by a 15 or 20 amp circuit breaker or
time delay fuse.
•A properly grounded 3-prong receptacle
should be located within reach of the
drawers’ 56” long power cord.
•Locate the receptacle in an adjacent cabinet.
– within 42” of the right side or,
– within 16” of the left side or,
– A recessed receptacle may be located on
the right side of the cutout, 7” from the
back of the cabinet. In this location, the
excess power cord should be coiled and
secured to the warming drawer side with
the power cord clip.
•When two warming drawers are installed
side to side, they can operate from the same
receptacle.
IMPORTANT: (Please read carefully).
The power cord of this appliance is equipped
with a three-prong (grounding) plug that
mates with a standard three-prong grounding
wall receptacle to minimize the possibility of
electric shock. The customer should have the
wall receptacle and circuit checked by a
qualified electrician to make sure the recep-
tacle is properly grounded and has the correct
polarity.
•Where a standard two-prong wall receptacle
is encountered, it is the personal responsibil-
ity and obligation of the customer to have it
replaced with a properly grounded three-
prong wall receptacle.
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
DO NOT USE AN EXTENSION CORD.
Grounding
the
Appliance
•Electrical power cord is located on the right
side of the warming oven. Locate the outlet
within reach of the 56” long power cord in
an adjacent cabinet, within 42” of the right
side or 16” from the left side of the cutout. A
recessed receptacle can be installed on the
right side of the cutout, 7” max. from the
rear of cabinet.
Drill 1-1/2" Hole
For Power Cord For
Left or Right Side
Outlet Location
Recessed
Receptacle 7"
Max. From Rear
on Right Side.

5
Installation Preparation
Warming Drawer
• Place carton on a flat surface.
•Open one end of the carton and lift off the
top piece.
• Lift the warmer up and out of the carton.
•Place the drawer on top of the shipping
carton to protect the drawer front and the
finished flooring.
• Remove all packing materials and tape.
• Locate package containing 4 wood screws
and set aside.
Remove
Packaging
and Parts
•When installed, the front face of the drawer
will be nearly flush with adjacent cabinetry
doors.
•Drawer overlaps will conceal cut edges on all
sides of the opening.
The rough opening for the drawer must be:
– Depth - 23-1/2” min. from inside back to
front of cabinet frame.
– Width - 25-1/2” for 27” wide models,
28-1/2” for 30” wide models.
– Height - 9-1/4”.
•5” min. above floor or 1” above toekick.
23-1/4” from floor to bottom of cutout is
recommended for under countertop
installation.
Installation below a cooktop:
•Warming drawers are approved for installa-
tion below only certain specified cooktop
models. See the label attached to the top of
the warming drawer for approved models.
Installation
Below a
Countertop
Dim. A
ZKD30 28-1/2”
ZKD27 25-1/2”
Note: If you are installing in frameless cabi-
nets, it may be necessary to install 1/2” wide
cleats to accept drawer mounting screws. See
drawer to find exact locations of mounting
screws.
Side to Side Installation:
•Install two warming drawers in separate
cutouts. Allow 2" min. between cutouts.
Parts provided:
• 4 Wood Screws
*Note: When installing the warming drawer under a
cooktop, allow 2" min. clearance from bottom of cooktop
burner box to the top of cutout. See the label attached to the
top of the warming drawer for approved cooktop models.
Electrical
Outlet 16" Max.
From Left Side.
23-1/2" Min.
25"
1-1/2" Cabinet Top
36"
Countertop
Height
2" Min.*
A9-1/4"
Electrical Outlet 42" Max.
From Right Side.
Electrical Outlet
Flush With Side
of Cabinet 7" Max.
9"
Install
2x4 or 2x2
Anti-Tip Block
Against Rear
Cabinet Wall
9" From Floor
to Bottom
of Block 7"
2"
Min.
Side to Side Installation

6
Design Information
Warming Drawer
Installation
Below
Wall Ovens
When installed under a wall oven:
Warming drawers are approved for installation
below only certain specified wall oven models.
See the label attached to the top of the
warming drawer for approved models.
•When installed, the front face of the drawer
will be nearly flush with adjacent cabinetry
doors.
•Drawer overlaps will conceal cut edges on all
sides of the opening.
INSTALLATION
BELOW A
SINGLE OVEN
Note: Additional clearance between
cutouts may be required. Check to be
sure that oven supports above the
Warming Drawer location does not
obstruct the required interior 23-1/2”
depth and 9-1/4” height.
Note: Additional clearance between
cutouts may be required. Check to be
sure that oven supports above the
Warming Drawer location does not
obstruct the required interior 23-1/2”
depth and 9-1/4” height.
Dim. A Dim. B
ZKD30 28-1/2” 30”
ZKD27 25-1/2” 26-3/4”
The rough opening for the drawer must be:
– Depth – 23-1/2” min. from inside back to
front of cabinet frame.
– Width – 25-1/2” for 27” wide models,
28-1/2” for 30” wide models.
– Height - 9-1/4”.
– Allow 2” min. between oven and drawer
cutouts for clearance of overlaps.
Note: If you are installing in frameless cabi-
nets, it may be necessary to install 1/2” wide
cleats to accept drawer mounting screws. See
drawer for mounting screw locations.
INSTALLATION
BELOW A
DOUBLE OVEN
1" Min. Above Toekick or Adjust
to Oven Installation Height
A
2" Min.
Allow 5/8"
Overlap on
All Sides
B
10-1/2"
23-1/4"
23-1/2" Min.
Inside
Oven
Cutout
9-1/4"
2x2 or 2x4
Anti-Tip Block
Against Rear
Wall, 9" From
Floor to
Bottom of
Block
9"
A
2" Min.
Allow 5/8"
Overlap on
All Sides
B
10-1/2"
23-1/4"
23-1/2" Min.
Inside
1" Min. Above Toekick
Oven
Cutout
2x2 or 2x4
Anti-Tip Block
Against Rear
Wall, 9" From
Floor to
Bottom of
Block
9"
9-1/4"

7
Installation
Warming Drawer
Step 1
Install
Anti-Tip
Brackets
Provide
Cabinet
Support
Important: When installed below a single or double oven,
check to be sure that any oven supports above the cutout do not
obstruct the 23-1/2” required depth of the warming drawer cutout.
•A 2” min. clearance between oven and
warming drawer cutouts are required.
Additional clearance may be required if 2 x 4
blocks are used to support runners or solid
floor of the oven above.
•The warmer drawer may be supported by
either a solid bottom, 2 x 4 or 2 x 2 run-
ners.
•The support must be level and rigidly
mounted, flush with the bottom edge of the
cutout.
– There is no way to level the drawer once it
has been installed. Be sure supports are
level.
•The entire weight of the drawer is supported
by the runners or solid floor and must be
capable of supporting 150 lbs.
Step 2
Install
Warming
Drawer
•Slide left corner of the drawer into the
opening.
•Push power cord into the hole leading to the
outlet location. Thread the cord through as
drawer is being pushed back into the open-
ing. Check to be sure power cord does not
get trapped under the drawer.
– If the outlet is installed inside the opening,
plug the cord into the outlet. Coil power
cord and secure to warming drawer side
with power cord clip.
•Push the drawer back until the front flange is
flush to the cabinet front.
ANTI-TIP PRECAUTIONS
An anti-tip brace must be installed to
prevent the drawer from tipping forward
when opened and loaded.
Failure to do so could result in personal
injury.
WARNING
•Open the drawer fully.
•Drill pilot holes through the holes in the
overlaping frame, one on each corner.
•Drive wood screws provided into each
corner.
23-1/2"
22"
27"
2"x 4" or
Equivalent Runners
23-1/2"
25"
30"
2"x 4" or
Equivalent Runners
9"
2x4 or 2x2
Runners or Solid
Bottom
Install
2x4 or 2x2
Anti-Tip Block
Against Rear
Cabinet Wall
9" From Floor
to Bottom
of Block

8
ZXD27B, ZXD30B Accessory
Installation of a Custom Panel
STEP 1:
•Open the drawer fully.
• Turn the warming drawer off.
STEP 2:
Remove original drawer front
• Remove two screws on each side and one
screw at the bottom of the drawer edge.
•Remove two screws on the inside of the
drawer at the top. Retain all screws.
– Support the glass drawer front as you
remove screws to prevent the possibility of
falling.
This kit contains a mounting panel to support
a trimless custom drawer front up to 3/4”
thick. A custom handle of your choice, must be
installed on the new panel.
Important: The warming drawer should be
installed according to the installation instruc-
tions packed with the product. The original
drawer front panel with handle will be re-
moved and discarded to make this installa-
tion.
• Cut edges of the drawer panel will be seen
and must be finished for best appearance.
• The custom drawer front panel, both raised
and flat design, should be constructed in
the same manner as typical cabinet doors.
• Order the custom drawer panel from the
cabinet manufacturer. Be sure to provide
the exact dimensions so that the panel is
constructed accurately.
• Order a custom handle to complement or
match surrounding cabinetry handles.
STEP 3:
Prepare the custom panel
• The custom panel must be sized to fit the
dimensions shown for your model.
• Drill a 5/16” diameter hole through the
appearance side of the panel. This hole
will hold the lamp jewel.
–A Brad point drill bit is recommended.
Tool and Materials required:
• Phillips screwdriver
• Drill and appropriate bits
(Brad point recommended for drilling through
wood panels)
• Custom panel
• Custom handle
• Adhesive recommended for metal to wood
Parts Supplied
• Lamp Jewel
• Metal mounting panel
A
10-1/2" 1-13/16"
1-3/4"
Drill 5/16" Dia.
Through Custom
Panel For Lamp Jewel
A = 26-3/4" for 27" models
A = 30" for 30" models

9
ZXD27B, ZXD30B Accessory
Installation of a Custom Panel
STEP 4:
Secure custom panel to metal mounting panel
• Lay the custom panel, appearance side down, on a
clean surface.
• Place the flat side of the metal panel onto the back side
of the custom panel, with the mounting flanges facing
up.
• Align the lamp hole in the panel with the mounting
panel.
• Check top, bottom and side dimensions from the metal
panel to wood panel edges.
STEP 5:
Apply adhesive to custom panel less than 3/4” thick
• Separate the custom panel and metal panel.
• Apply a few horizontal beads of adhesive to the metal
panel. Avoid adhesive within 1” of lamp hole area and
outer edges.
STEP 5A:
Secure 3/4” thick panels with screws
3/4” thick panels may be secured to the metal panel with
screws.
• Use the metal panel as a template. Position the metal
panel over the back side of the custom panel and drill
pilot holes. Drill pilot holes sized to match screws
being used (screws not provided).
Caution: Select screw length carefully to avoid penetration of the finished side.
STEP 6
Install lamp jewel
Turn the assembly appearance side up.
• Insert the red indicator lamp jewel through the front
custom panel surface as shown.
– If the hole is slightly oversized, apply a small amount
of adhesive to the barrel.
STEP 7
Install Custom Handle
A custom handle (not supplied) must be installed.
• Drill pilot holes through the front of the custom panel
and through the metal panel to match the chosen
handles.
Note: The handle screws should be installed through the
metal panel, the custom panel and into the custom
handle.
STEP 8:
Install assembled panel to the warming drawer
• Install the custom panel assembly to the exposed
drawer front using the original 7 screws.
Insert
Jewel
3/16"
Align Holes
1/4"
7/32"
1/4" Top
Bottom
Custom Handle
Back Side of Appearance Panel
with Support Panel

10
JXPN1 Accessory
Pan Kit for Warming Drawer
This kit contains supports and pans to fit your
new Warming Drawer.
This kit is designed to fit both 27” and 30”
wide models. Select the parts for your model
and discard the parts that do not fit.
1. Remove the packaging and separate parts.
2. Open the drawer fully.
3. Select the side to side rails to fit your
model.
4. Drop a side to side rail (with slots in the
top) into the slots at the rear and one in
the front of the drawer. Note that slots fit
only one way, with the wide interlocking
tabs on the right sides.
5. Drop filler panel into the right side.
Two sets of Side to Side Support Rails
(one set for 27” and one for 30” wide models)
6. Drop one or two front to back rails into
matching slots.
One Full size pan with Lid, 21” long x 13” wide x 4” deep
Two Half Size Pans with Lids, 21” long x 6-1/2” wide
x 4” deep
Two Quarter Size Pans with Lids, 10-1/2” long
x 6-1/2” wide x 4” deep
30"
Models
27"
Models
27" Models 30" Models
Wide Slots
Towards Inside
Small Slots
Towards Front
Drop Rail
Into Small
Slots
Wide Slots
Towards Rear
Filler Panel
27" Models
Front to Back
Support Rails
For All Models
Filler Panel
30" Models
Parts Included

11
JXPN1 Accessory
Pan Kit for Warming Drawer
7. Arrange pans to suit food storage
needs.
8. Discard the Side to side rails and filler
panel not used.
Important Notes:
• Use the pan lids to keep foods moist.
• Do not use plastic wrap! Plastic wrap
could melt and damage the interior of
your warming drawer.
• Do not place water in the bottom of the
warming drawer pan. Moisture can
form on cabinets or drip below.
Combinations with full size pan Combinations without full size pan.

Pub. No. 49-8937
Part No. 164D3333P167
 1999 GE Appliances
(N.D. 298) 4/99
977-0160-001
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
To obtain specific information concerning any
Monogram product or service, call GE Answer Center®
consumer information service at 800.626.2000—any
time, day or night.
For Monogram local service in your area, call
1-800-444-1845.
NOTE: Product improvement is a continuing endeavor at General
Electric. Therefore, materials, appearance and specifications are
subject to change without notice.
Monogram.
®
General Electric Company
Louisville, KY 40225