Geevon W22145 User manual

GEEVON COLOR ATOMIC CLOCK
Item No.W22145
User Manual
Features & Benefits:
DISPLAY UNIT
1. LIGHT/SNOOZE button
2. Radio controlled with WWVB
3. Time display
4. SNOOZE
5. Weekday
6. Calendar
7. Indoor temperature
8. Alarm
9. Indoor humidity
10. Moon phase
11. LIGHT/SNOOZE button
12.UP button
13.Down button
14.Set button
15.Alarm button
16 Wave button
17.Hang hole
18. Stand
19. Battery Compartment
Main features:
1.6 Function buttons: ， ， ， ， ，
2. Radio controlled with WWVB
3. Color display
4. Moon phase display
5. Display time and date
6. Week display
7. Indoor temperature display(℃/℉）: -9.9℃-50℃
8. Indoor humidity display: 20%-95%
9. Alarm with snooze function
10. Time zone
11. Comfort icon
12. Backlight
Setting up power supply Base device
Insert the DC connector into the connection socket
of the base station. Insert the mains plug into the
power outlet. The device is energized directly.
NOTICE! For permanent operation, the mains
power supply is required. Alternatively, a
power supply with batteries is also possible, to
keep the time setting in case of power failure.
NOTICE! When Receiving the RCC, the
backlight will turn off.
Automatic time setting
After the power supply was established, the clock
will automatically search for the radio signal. The
clock will automatically search for the radio signal.
If the clock fails to receive the time signal, go
ahead with the following steps:
1.Press and hold button for approx. 3 seconds
to initialize the radio signal reception again.
2. If the device is still not receiving the signal, the
time must be set manually.
Manual time setting
1.Press and hold button for approx. 3 seconds
to change to time setting mode.
2. Digits to be set are flashing.
3. Press or button to change the value.
4. Press button to confirm and continue to the
next setting.
5. Settings order: 12/24H>Time zone>Hours >
Minutes > Year > Month > Day > DST ON/OFF
6. Finally press the button to save the settings
and exit the setting mode.
Alarm setting
1.Press button to check Alarm .
Thank you for purchasing W22145 Color Atomic Clock
Please take a moment to read this guide and store it for
future reference.

2.When enter Alarm mode, Press and hold
button for approx. 3 seconds to enter the alarm
time setting mode. Digits to be set are flashing.
3.Press or button to change the value.
4.Press button to confirm and continue to the
next setting.
5.Settings order: Hours > Minutes
6. Finally press the button to save the settings
and exit the setting mode. Alarm will be activated
automatically.
7. Press button in normal display mode to
display the alarm time.
8. Then press button to turn on or turn off the
alarm. If the alarm turn on. The alarm symbol will
be displayed.
Snooze function
1.When the alarm sounds, press button to
activate the snooze function.
2. In normal mode, press and hold the button
to set the snooze time.
C/F select
In normal mode, press button to select ℃ or ℉.
Backlight
When connect with adaptor, press the button
to adjust the brightness. The setting order: High
light>Low light>off.
When work with batteries, press the button
turn on the backlight for 5 seconds.
NOTICE! For permanent operation, the mains
power supply is required. Alternatively, a power
supply with batteries is also possible, to keep
the time setting in case of power failure.
Comfort icons
1. Dry: When the humidity is lower than 40%, it will
show DRY on the display.
2. COM: When the temperature is between 20-28
℃, at the same time the humidity is between
40%-70%, it will show COM on the display
3. WET: When the humidity is higher than 70%, it
will show WET on the display
4. NO ICONS: When the temperature is not
between 20-28℃but humidity is between
40%-70%, it will not show any icon on the display.
Technical data
Power supply: DC 5V 150 mA adaptor
Batteries: 3x AAA Battery
Temperature measuring unit: °C / °F
Temperature display range: -9.9°C – 50°C
Humidity display range: RH 20% - 95%
DISPLAY UNIT PLACEMENT
Place the display unit in a dry area free of dirt and
dust. Display unit stands up right for
tabletop/countertop use.
Important Placement Guidelines
a. To ensure accurate temperature measurement,
place units out of direct sunlight and away from
any heat sources or vents.
b. For better atomic signal, place unit away from
large metallic items, thick walls, metal surfaces, or
other objects that may lose the signal.
d. To prevent interference, place unit at least 3ft (1
m) away from electronic devices (TV, computer,
microwave, radio, etc.)
Technical Support
If your Geevon product does not operate properly,
please contact the seller on your order page or
shoot an email to : [email protected].