Geevon T228137 User manual
Unit displays
1.Time display
2.Indoor temperature
3.Alarm
4.Channel select
5.Pool temperature
6.Alert signal
7.Pool highest temperature alert
8.Temperature trend
9.Pool lowest temperature alert
10.Hang hole
11.Battery Compartment 3xAAA (not included)
12.Pedestal
13.Sensor temperature display
14.Transmission light
15.Temperature sensor
Buttons
A: DOWN and alarm button
B: UP button
C: Channel select button
D: Snooze and light button
E: Mode (set ) button
Main function:
1. Time display
2. Indoor temperature display(℃/℉）:0℃- 50℃
& 32℉- 122℉
3. Pool temperature display(℃/℉）: -40℃- 70℃
& -40℉- 158℉
4. 12HR & 24HR
5. ℃ & ℉
6. Pool temperature
7. Highest and lowest temperature in the pool
8. Pool temperature alarm
9. Alarms with snooze function
10. Low battery indicator
11. Backlight
12. 3 channels for remote sensor
1. Setting up power supply Base device
Proceed as follows:
1.Remove the battery compartment cover.
2.Insert the batteries into the battery compartment.
3.Ensure that the battery polarity (+/-) is correct.
4. Replace the battery compartment cover.
Remote sensor:
1.Rotate right to open the sensor.
2.Insert the batteries into the battery
compartment. Ensure that the battery polarity
(+/-) is correct.
3.Press CH button to set the channel selector
switch to the desired channel.
GEEVON WIRELESS POOL THERMOMETER
Item No.T228137
User Manual
Thank you for purchasing T228137 pool ther-
mometer
Please take a moment to read this guide and
store it for future reference.
MODE
/ALARM
1 2
A B C D E F10
11
12
7
8
9
3
4
5
6
13
14
15
Channel 1, Channel 2 or Channel 3. Hold the CH
button for approx. 3 seconds to reset values and
search for an RF signal.
NOTICE! Always make sure the channel
chosen on the display unit matches the chan-
nel option chosen on the pool sensor.
8. Temperature Alert setting
1. Press the ALERT button for approx. 3 seconds
and the current channel symbol starts flashing.
2. Press the ▲ or▼/Alarm button to set the
temperature.
3. Press ALERT button to confirm and continue to
the next setting.
4. Settings order: Pool highest temperature >
Pool lowest temperature
5. Press ALERT button to activate or deactivate
the Alarm for the currently selected temperature
Alert.
6.Press the CH button to select the channel.
When alert is triggered, press any button to stop
the alert. If you ignore the alarm, it will ring for 5
seconds of each minute.
9. Backlight
When connect with batteries, press the
SNZ/LIGHT button to turn on the backlight.
10. Technical data
Main unit
Batteries: 3x AAA Battery（Not Incl）
Temperature measuring unit: °C / °F
Indoor temperature display range: 0℃- 50℃&
32℉- 122℉
Remote sensor
Batteries: 2x AA Battery（Not Incl）
Temperature measuring unit: °F
Temperature measuring range: -40℉- 158℉
Transmission range: 100 m/328feet
Important Placement Guidelines
A. To maximize wireless range, place units away
from large metallic items, thick walls, metal
surfaces, or other objects that may limit wireless
communication.
B. To prevent wireless interference, place both
units at least 3ft (1 m) away from electronic
devices (TV, computer, microwave, radio, etc.)
Technical Support
If your Geevon product does not operate proper-
ly, please contact the seller on your order page or
NOTICE! This pool thermometer can be oper-
ated with one or more remote sensors. Each
remote sensor being connected must be
operated on a different channel. If only one
remote sensor is connected, it should be
operated on channel 1.
4. Replace the battery compartment cover.
2. Time setting
Manual time setting
1.Press and hold MODE button for approx. 3
seconds to change to time setting mode.
2.Digits to be set are flashing.
3.Press ▲or▼/ Alarm button to change the value.
4.Press MODE button to confirm and continue to
the next setting.
5.Settings order: 12HR /24HR switch >Hours >
Minutes
6.Finally press the MODE button to save the
settings and exit the setting mode.
3. Alarm setting
1. Press MODE button to check the Alarm time .
2. When enter Alarm mode, Press and hold MODE
button for approx. 3 seconds to enter the alarm
time setting mode. Digits to be set are flashing.
3. Press ▲or▼/ Alarm button to change the value.
4. Press MODE button to confirm and continue to
the next setting.
5. Settings order: Hours > Minutes
6. Finally press the MODE button to save the
settings and exit the setting mode.
7. Press MODE button in normal display mode to
display the alarm time.
8. Press ▼/ Alarm button to turn on or turn off the
alarms. If the alarm turn on. The alarm symbol
will be displayed.
4. Snooze function
When the alarm sounds, press SNOOZE button
to activate the snooze function,the snooze time is
5 minutes .
5. C/F select
In normal mode, press ▲ button to select ℃ or ℉.
6. 12/24H select
1.In normal mode press and hold MODE button
for approx. 3 seconds to change to time setting
mode.
2. Digits to be set are flashing.
3. Press ▲or▼/ Alarm button to change
12HR/24HR.
7. Channel select
In normal mode, press the CH button to select
Other Geevon Thermometer manuals
