Gefen EXT-3GSDI-441 User manual

EXT-3GSDI-441
User Manual
4x1 3GSDI Switcher
Release A8
*Preferred

ii
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install or place this unit near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the unit.
11. Only use attachments/accessories specied by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this unit, never handle or touch
this unit or power cord if your hands are wet or damp. Do not expose this
unit to rain or moisture.
13. Unplug this unit during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when
the unit has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the unit,
the unit has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this unit and/or accessories should never be
exposed to open ame or excessive heat. Always dispose of used batteries
according to the instructions.
Important Safety Instructions

Gefen warrants the equipment it manufactures to be free from defects in material and
workmanship.
If equipment fails because of such defects and Gefen is notied within two (2) years from
the date of shipment, Gefen will, at its option, repair or replace the equipment, provided
that the equipment has not been subjected to mechanical, electrical, or other abuse or
modications. Equipment that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of repair. Such repairs
are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or tness for any particular purpose, all of
which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their original
condition.
The information in this manual has been carefully checked and is believed to be accurate.
However, Gefen assumes no responsibility for any inaccuracies that may be contained
in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages. The technical information contained herein
regarding the features and specications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Support section of the Gefen Web site at www.gefen.com.
iii
Warranty Information

iv
Technical Support
[phone] [phone]
8:00 AM to 5:00 PM Monday - Friday, Pacic Time
Fax
[phone]
Email
[email protected]
Web
http://www.gefen.com
Mailing Address
Gefen, LLC
c/o Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
Product Registration
Register your product here: http://www.gefen.com/kvm/Registry/Registration.jsp
iv
Contacting Gefen Technical Support

v
• The 4x1 3GSDI Switcher will accept the following formats:
► SDI (SMPTE 259M-C, 270 Mbps)
► HDSDI (SMPTE 292M, 1.485 Gbps)
► 3GSDI (SMPTE 424M / 425M, 2.97 / 3.0 Gbps)
4x1 3GSDI Switcher is a trademark of Gefen, LLC.
© 2015 Gefen, LLC. All Rights Reserved. All trademarks are the property of their respective owners.
Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation
without prior written notice.
v
Operating Notes
This product uses UL or CE listed power supplies.
Pb

vi
Features and Packing List
Features
• Switches between four 3G-SDI sources to a single output device without latency or
signal degradation
• Resolutions up to 1080p are supported
• Backwards-compatible with SDI and HD-SDI
• Supports NTSC, PAL, and all HD formats
• Switching is controlled via front panel push button, IR Remote (included), or RS-232
Commands
• Plug-and-Play Installation
• Locking Power Supply
Packing List
The 4x1 3GSDI Switcher ships with the items listed below. If any of these items are not
present in the box when you rst open it, immediately contact your dealer or Gefen.
• 1 x 4x1 3GSDI Switcher
• 1 x 6 ft. DB-9 cable
• 1 x IR Remote Control Unit
• 1 x 5V DC locking power supply
• 1 x Quick-Start Guide
1080P

viii
Table of Contents
1 Getting Started
Introduction............................................................................................................ 2
Front / Rear / Bottom Panel .......................................................................... 2
IR Remote Control ........................................................................................ 4
Installing the IR Remote Battery ................................................................... 6
Setting the IR Remote Channel .................................................................... 6
Installation ............................................................................................................. 7
Connection Instructions................................................................................. 7
Sample Wiring Diagram ................................................................................ 7
2 Basic Operation
Switching Sources............................................................................................... 10
Using the Front Panel ................................................................................. 10
Using the IR Remote................................................................................... 11
DIP Switch Conguration .................................................................................... 12
3 Advanced Operation
RS-232 Control.................................................................................................... 16
RS-232 Interface ......................................................................................... 16
RS-232 Settings .......................................................................................... 16
Commands.......................................................................................................... 17
4 Appendix
Specications ...................................................................................................... 20

1 Getting Started
4x1 3GSDI Switcher
Introduction............................................................................................................ 2
Front / Rear / Bottom Panel .......................................................................... 2
IR Remote Control ........................................................................................ 4
Installing the IR Remote Battery ................................................................... 6
Setting the IR Remote Channel .................................................................... 6
Installation ............................................................................................................. 7
Connection Instructions................................................................................. 7
Sample Wiring Diagram ................................................................................ 7

page | 2
Page Title
Front / Rear / Bottom Panel
®
IR Power 1 2 3 4 Select
4x1 3GSDI Switcher
In 2 In 3 In 4 Out RS-232
EXT-3GSDI-441
5V DCIn 1
ON SAB
1 2 3 4
®
IR Power 1 2 3 4 Select
4x1 3GSDI Switcher
In 2 In 3 In 4 Out RS-232
EXT-3GSDI-441
5V DCIn 1
ON SAB
1 2 3 4
®
IR Power 1 2 3 4 Select
4x1 3GSDI Switcher
In 2 In 3 In 4 Out RS-232
EXT-3GSDI-441
5V DCIn 1
ON SAB
1 2 3 4
Introduction
Getting Started Getting Started
1
2
5 6 7 8
9
3 4

page | 3
Page TitleIntroduction
ID Name Description
1 IR Receives signals from the included IR
remote control.
2 Power This LED indicator will glow solid blue
when the matrix is powered.
3Input Indicators (1 - 4) These LED indicators display the
currently selected input. The currently
selected input will glow solid blue.
4Select Press this button to cycle through each
of the input ports.
5 In 1 - In 4 Connect up to four SDI sources to these
ports using BNC cables.
6 Out Connect a BNC cable from this port to
the SDI display.
7RS-232 Connect an RS-232 cable from this port
to the automation device.
8 5V DC Connect the included power supply from
this power receptacle to an available
electrical outlet.
9 DIP switches Refer to DIP Switch Configuration (page
12) for information on using these DIP
switches.
Getting Started

page | 4
Introduction
Getting Started Getting Started
IR Remote Control
ID Name Description
1 Activity indicator This LED will be activated momentarily
each time an input button is pressed.
2 Input buttons Press these buttons to select an input
(1 - 4).
21
3 4
2
1

page | 5
Introduction
Getting Started
P/N: RMT-4-IRN
ON
1 2
www.gefen.com
ID Name Description
1 DIP switch bank Use these DIP switches to set the IR
channel of the remote. See the next page
for more information.
2 Primary battery slot
(shown without battery)
Holds the battery for operating the remote.
Use only 3V CR2032-type batteries. Make
sure that the positive (+) side of the battery
is facing up.
3 Alternate battery slot Allows for the installation of secondary
(backup) battery.
23
1

page | 6
Getting Started
Introduction
Getting Started
Installing the IR Remote Battery
The IR remote control unit ships with two batteries. Only one battery is required for
operation. The second battery is a spare.
1. Remove the back cover the IR Remote Control unit.
2. Insert the included battery into the primary battery slot. The positive (+) side of the
battery should be facing up.
3. Replace the back cover.
Setting the IR Remote Channel
In order for the included IR remote control to communicate with the 4x1 3GSDI Switcher,
the IR remote control must be set to the same channel as the switcher.
IR Channel DIP settings
0
(default)
1 2
ON
1
1 2
ON
1 2
2
1 2
ON
3
1 2
ON
P/N: RMT-4-IRN
ON
1 2
www.gefen.com
Warning
Use only 3V CR2032-type batteries. Risk of explosion if battery is replaced by
an incorrect type. Dispose of used batteries according to the instructions.
DIP switches

page | 7
Installation
Getting Started
Connection Instructions
►Video
1. Connect a BNC cable from each SDI source to the input ports (In 1 - In 4) on the
4x1 3GSDI Switcher.
2. Connect a BNC cable from the SDI display to the Out port on the 4x1 3GSDI Switcher.
►RS-232
3. Connect an RS-232 cable from the RS-232 port on the matrix to the RS-232 connector
on the automation controller.
►Power
4. Connect the included power supply to the 5V DC power receptacle and connect the
power cord to an available electrical outlet.
Sample Wiring Diagram
3G-SDI CABLE
3G-SDI Display
3G-SDI Source
3G-SDI Source
3G-SDI Source
3G-SDI Source
Switcher
EXT-3GSDI-441
RS-232
Automation
Control Device
RS-232 CABLE

4x1 3GSDI Switcher
2 Basic Operation
Switching Sources............................................................................................... 10
Using the Front Panel ................................................................................. 10
Using the IR Remote................................................................................... 11
DIP Switch Conguration .................................................................................... 12

page | 10
Using the Front Panel
1. Each of the input indicators (1 - 4) on the front panel represents an SDI input
(In 1 - In 4) on the rear of the unit. The input indicator, for the currently selected
source, will glow solid blue.
2. Press and release the Select button on the front panel to advance to the next input.
3. Continue to press and release the Select button, as desired, to cycle through each
input.
4. Once input indicator 4 is illuminated, pressing the Select button again will select
input 1. Input indicator 1 will now be illuminated.
®
IR Power 1 2 3 4 Select
4x1 3GSDI Switcher
In 2 In 3 In 4 Out RS-232
EXT-3GSDI-441
5V DCIn 1
ON SAB
1 2 3 4
Switching Sources
Basic OperationBasic Operation Basic OperationBasic Operation
®
IR Power 1 2 3 4 Select
4x1 3GSDI Switcher
In 2 In 3 In 4 Out RS-232
EXT-3GSDI-441
5V DCIn 1
ON SAB
1 2 3 4
®
IR Power 1 2 3 4 Select
4x1 3GSDI Switcher
In 2 In 3 In 4 Out RS-232
EXT-3GSDI-441
5V DCIn 1
ON SAB
1 2 3 4
®
IR Power 1 2 3 4 Select
4x1 3GSDI Switcher
In 2 In 3 In 4 Out RS-232
EXT-3GSDI-441
5V DCIn 1
ON SAB
1 2 3 4
Select button
Input indicators