gefran AFE200 4 Series User manual

...... Instruction Manual
Active Front End Regenerative
Power Supply Unit
AFE200-...-4
AFE200-...-6
Industrial application

2AFE200 • Instruction Manual
Information about this manual
Software version
This manual is updated according the software version V 7.x.2.
The identication number of the software version is indicated on the identication plate of the
AFE or can be checked with the Firmware ver.rel - PAR 490 parameter, menu 2.5
General information
Before using the product, read the safety instruction section carefully. Keep the manual in a
safe place and available to engineering and installation personnel during the product function-
ing period.
Gefran S.p.A has the right to modify products, data and dimensions without notice. The data
can only be used for the product description and they can not be understood as legally stated
properties.
Thank you for choosing this Gefran product.
We will be glad to receive any possible information which could help us improving this manual.
The e-mail address is the following: [email protected].
All rights reserved

AFE200 • Instruction Manual 3
Table of contents
Information about this manual ................................................. 2
1 - Safety Precautions ............................................................... 6
1.1 Symbols used in the manual .................................................................................... 6
1.2 Safety precaution...................................................................................................... 7
1.3 General warnings ..................................................................................................... 7
1.4 Instruction for compliance with UL Mark (UL requirements), U.S. and Canadian
electrical codes............................................................................................................... 9
2 - Introduction to the product................................................ 10
2.1 Product type designation........................................................................................ 12
2.1.1 Parallel congurations...........................................................................................13
3 - Transport and storage........................................................ 14
3.1 General................................................................................................................... 14
3.2 Permissible Environmental Conditions................................................................... 15
4 - Mechanical installation ...................................................... 16
4.1 Inclination and mounting clearance........................................................................ 16
4.2 Fastening positions................................................................................................. 17
5 - Wiring Procedure................................................................ 22
5.1 Power section......................................................................................................... 25
5.1.1 Cable Cross Section..............................................................................................25
5.1.2 EMC guide line......................................................................................................29
5.1.3 Block diagram power section ................................................................................30
5.1.4 Power line connection ...........................................................................................32
5.1.5 DC output connection............................................................................................33
5.1.6 Connection of fans power supply ..........................................................................35
5.2 Regulation section.................................................................................................. 36
5.2.1 Removing the terminal cover.................................................................................36
5.2.2 Cable Cross Section..............................................................................................36
5.2.3 Regulation section connection ..............................................................................36
5.2.4 Switches, jumpers and LED ..................................................................................38
5.3 Serial interface (XS connector)............................................................................... 41
5.3.1 AFE / RS 485 Port (not insulated) point-to-point connection.................................41
5.3.2 AFE / RS485 port point-to-point connection (with insulation)................................43
5.3.3 RS 485 multi-drop connection...............................................................................43
5.4 Typical connection diagrams (with Pre-charge Kit) ........................................................... 44
5.5 Precharge Kit.......................................................................................................... 48
5.5.1 Fuses internal to the pre-charge kit.......................................................................48
5.5.2 Pre-charge kit dimensions and Cable Cross Section............................................49
5.6 LCL Filters ............................................................................................................. 51
5.6.1 LR3-AFE (Choke) Dimensions, Cable Cross Section and data ............................54
5.6.2 LC-AFE (Choke + capacitors) Dimensions, Cable Cross Section and data..........56
5.6.3 L-AFE (Choke) Dimensions, Cable Cross Section and data.................................57
5.6.4 C-AFE (Capacitor) Dimensions and Cable Cross Section ....................................58
6 - Use of the keypad ............................................................... 59
6.1 Description.............................................................................................................. 59
6.2 Navigation............................................................................................................... 60
6.2.1 Scanning of the rst and second level menus.......................................................60
6.2.2 Display of a parameter ..........................................................................................60
6.2.3 Scanning of the parameters .................................................................................61

4AFE200 • Instruction Manual
6.2.4 List of the last parameters modied ......................................................................61
6.2.5 “Goto parameter” function .....................................................................................61
6.3 Parameter modication........................................................................................... 62
6.4 How to save parameters......................................................................................... 63
6.5 Conguration of the display.................................................................................... 64
6.5.1 Language selection ...............................................................................................64
6.5.2 Selection of Easy / Export mode ...........................................................................64
6.5.3 Startup display.......................................................................................................64
6.5.4 Back-lighting of the display....................................................................................64
6.6 Alarms..................................................................................................................... 65
6.6.1 Alarm reset ............................................................................................................65
6.7 Messages ............................................................................................................... 65
6.8 Saving and recovery of new parameter settings .................................................... 66
6.8.1 Selection of the keypad memory...........................................................................66
6.8.2 Saving of parameters on the keypad.....................................................................66
6.8.3 Load parameters from keypad ..............................................................................67
6.8.4 Transfer of parameters between AFE200..............................................................67
7 - Commissioning via keypad .............................................. 68
7.1 Startup Wizard........................................................................................................ 71
7.2 Programming ......................................................................................................... 74
7.2.1 Menu display modes .............................................................................................74
7.2.2 Programming of “function block” analog and digital input signals .........................74
7.2.3 Variable interconnections mode ............................................................................74
8 - Description of parameters and functions (Expert list).... 76
Legend ...........................................................................................................................76
8.1 Parameters on selection lists, but not displayed on keypad................................. 150
8.2 Selection Lists ...................................................................................................... 155
9 - Troubleshooting................................................................ 160
9.1 Alarms................................................................................................................... 160
9.1.1 “ExtIO fault” Alarm ..............................................................................................163
9.1.2 “Fastlink fault” Alarm............................................................................................164
9.2 Messages ............................................................................................................. 165
10 - Specication ................................................................... 168
10.1 Environmental Conditions................................................................................... 168
10.2 Standards ........................................................................................................... 168
10.3 Accuracy............................................................................................................. 168
10.3.1 Current control...................................................................................................168
10.3.2 Voltage control...................................................................................................168
10.3.3 Current rating ....................................................................................................168
10.4 Overload............................................................................................................. 169
10.5 DC circuit............................................................................................................ 169
10.6 Electrical data..................................................................................................... 170
10.7 Voltage level of AFE200 for safe operations ...........................................................172
10.8 Cooling ............................................................................................................... 173
10.9 Weight and dimensions ...................................................................................... 174
11 - Options ............................................................................ 181
11.1 Optional external fuses (mandatory)................................................................... 181
11.1.1 Fuses for connection mains side (F1) ...............................................................181
11.1.2 Fuses for connection DC side ...........................................................................182
11.2 EMC lter............................................................................................................ 184
11.3 Installation of optional cards ............................................................................... 185
11.4.1 Shielding of optional card connections..............................................................187

AFE200 • Instruction Manual 5
Appendix 1 - Design .............................................................. 188
A1.1 Single-motor calculation based on motor output power ..................................... 188
A1.2 Calculation for multi-motor system..................................................................... 189
Appendix 2 - Parallel connection (400 ... 1650kW sizes).... 192
A 2.1 Introduction........................................................................................................ 192
A 2.2 Compatibility of IGBT modules......................................................................... 194
A 2.3 MS-SL interface cable wiring sizes 400...710 kW ............................................. 195
A 2.4 MS-SL interface cable wiring sizes 900 kW...1 MW .......................................... 196
A 2.5 MS-SL interface cable wiring size 1.35 MW...................................................... 197
A 2.6 MS-SL interface cable wiring size 1.65 MW...................................................... 198
A 2.7 Jumpers and Switches ...................................................................................... 199
A 2.8 LEDs.................................................................................................................. 199
Appendix 3 - Block Diagrams ............................................... 202
System Diagrams Index ............................................................................................. 202
Drive overview............................................................................................................ 202
Reference................................................................................................................... 202
Commands ................................................................................................................. 203
Digital inputs............................................................................................................... 204
Digital outputs............................................................................................................. 205
Analog inputs.............................................................................................................. 206
Analog outputs............................................................................................................ 208
Current Control........................................................................................................... 209
Active Curr Cong ...................................................................................................... 210
Functions.....................................................................................................................211

6AFE200 • Instruction Manual
1 - Safety Precautions
1.1 Symbols used in the manual
Indicates a procedure, condition, or statement that, if not strictly observed, could result
in personal injury or death.
Indique le mode d’utilisation, la procédure et la condition d’exploitation. Si ces consignes ne
sont passtrictement respectées, il y a des risques de blessures corporelles ou de mort.
Indicates a procedure, condition, or statement that, if not strictly observed, could result
in damage to or destruction of equipment.
Indique et le mode d’utilisation, la procédure et la condition d’exploitation. Si ces consignes
ne sont pas strictement respectées, il y a des risques de détérioration ou de destruction des
appareils.
Indicates that the presence of electrostatic discharge could damage the appliance.
When handling the boards, always wear a grounded bracelet.
Indique que la présence de décharges électrostatiques est susceptible d’endommager l’appa-
reil. Toujours porter un bracelet de mise à la terre lors de la manipulation des cartes.
Indicates a procedure, condition, or statement that should be strictly followed in order to
optimize these applications.
Indique le mode d’utilisation, la procédure et la condition d’exploitation. Ces consignes doivent
êtrerigoureusement respectées pour optimiser ces applications.
Note ! Indicates an essential or important procedure, condition, or statement.
Indique un mode d’utilisation, de procédure et de condition d’exploitation essentiels ou importants
Qualied personnel
For the purpose of this Instruction Manual , a “Qualied person” is someone who
is skilled to the installation, mounting, start-up and operation of the equipment and
the hazards involved. This operator must have the following qualications:
- trained in rendering rst aid.
- trained in the proper care and use of protective equipment in accordance with
established safety procedures.
- trained and authorized to energize, de-energize, clear, ground and tag circuits
and equipment in accordance with established safety procedures.
Personne qualiée
Aux ns de ce manuel d’instructions, le terme « personne qualiée » désigne toute personne
compétente en matière d’installation, de montage, de mise en service et de fonctionnement
de l’appareil et au fait des dangers qui s’y rattachent. L’opérateur en question doit posséder
les qualications suivantes :
- formation lui permettant de dispenser les premiers soins
Warning!
Caution
Attention

AFE200 • Instruction Manual 7
- formation liée à l’entretien et à l’utilisation des équipements de protection selon les consigne
de sécurité en vigueur
- formation et habilitation aux manoeuvres suivantes : branchement, débranchement,
vérication des isolations, mise à la terre et étiquetage des circuits et des appareils selon les
consignes de sécurité en vigueur
Use for intended purpose only
The power drive system (electrical drive + application plant) may be used only for
the application stated in the manual and only together with devices and compo-
nents recommended and authorized by Gefran.
Utiliser uniquement dans les conditions prévues
Le système d’actionnement électrique (drive électrique + installation) ne peut être utilisé que
dans les conditions d’exploitation et les lieux prévus dans le manuel et uniquement avec les
dispositifs et les composants recommandés et autorisés par Gefran.
1.2 Safety precaution
The following instructions are provided for your safety and as a means of prevent-
ing damage to the product or components in the machines connected. This sec-
tion lists instructions, which apply generally when handling electrical drives.
Specic instructions that apply to particular actions are listed at the beginning of
each chapters.
Les instructions suivantes sont fournies pour la sécurité de l’utilisateur tout comme pour éviter
l’endommagement du produit ou des composants à l’intérieur des machines raccordées. Ce
paragraphe dresse la liste des instructions généralement applicables lors de la manipulation
des drives électriques.
Les instructions spéciques ayant trait à des actions particulières sont répertoriées au début
de chaque chapitre.
Read the information carefully, since it is provided for your personal safety and will
also help prolong the service life of your electrical drive and the plant you connect
to it.
Lire attentivement les informations en matière de sécurité personnelle et visant par ailleurs à
prolonger la durée de vie utile du drive tout comme de l’installation à laquelle il est relié.
1.3 General warnings
This equipment contains dangerous voltages and controls potentially dangerous rotat-
ing mechanical parts. Non-compliance with Warnings or failure to follow the instructions
contained in this manual can result in loss of life, severe personal injury or serious
damage to property.
Cet appareil utilise des tensions dangereuses et contrôle des organes mécaniques en mou-
vement potentiellement dangereux. L’absence de mise en pratique des consignes ou le non-
respect des instructions contenues dans ce manuel peuvent provoquer le décès, des lésions
corporelles graves ou de sérieux dégâts aux équipements.
This equipment contains dangerous voltages and controls potentially dangerous rotat-
ing mechanical parts. Non-compliance with Warnings or failure to follow the instructions
contained in this manual can result in loss of life, severe personal injury or serious
damage to property.
Les drives occasionnent des mouvements mécaniques. L’utilisateur est tenu de s’assurer
que de tels mouvements mécaniques ne débouchent pas sur des conditions d’insécurité.
Les butées de sécurité et les seuils d’exploitation prévus par le fabricant ne doivent être ni
contournés ni modiés.
Warning!

8AFE200 • Instruction Manual
Only suitable qualied personnel should work on this equipment, and only after becom-
ing familiar with all safety notices, installation, operation and maintenance procedures
contained in this manual. The successful and safe operation of this equipment is
dependent upon its proper handling,installation, operation and maintenance.
Seul un personnel dûment formé peut intervenir sur cet appareil et uniquement après avoir
assimilé l’ensemble des informations concernant la sécurité, les procédures d’installation, le
fonctionnement et l’entretien contenues dans ce manuel. La sécurité et l’efcacité du fonction-
nement de cet appareil dépendent du bon accomplissement des opérations de manutention,
d’installation, de fonctionnement et d’entretien.
In the case of faults, the drive, even if disabled, may cause accidental movements if it
has not been disconnected from the mains supply.
En cas de panne et même désactivé, le drive peut provoquer des mouvements fortuits s’il n’a
pas été débranché de l’alimentation secteur.
Electrical Shock
The DC link capacitors remain charged at a hazardous voltage even after cutting off the
power supply.
Never open the device or covers while the AC Input power supplyis switched on.
Minimum time to wait before working on the terminals or inside the device is listed in
section 10.6 .
Risque de décharge électrique
Les condensateurs de la liaison à courant continu restent chargés à une tension dangereuse
même après que la tension d’alimentation a été coupée.
Ne jamais ouvrir l’appareil lorsqu’il est suns tension. Le temps minimum d’attente avant de
pouvoir travailler sur les bornes ou bien àl’intérieur de l’appareil est indiqué dans la section
10.6 .
Electrical Shock and Burn Hazard:
When using instruments such as oscilloscopes to work on live equipment, the oscil-
loscope’s chassis should be grounded and a differential probe input should be used.
Care should be used in the selection of probes and leads and in the adjustment of the
oscilloscope so that accurate readings may be made. See instrument manufacturer’s
instruction book for proper operation and adjustments to the instrument.
Décharge Èlectrique et Risque de Brúlure : Lors de l’utilisation d’instruments (par example
oscilloscope) sur des systémes en marche, le chassis de l’oscilloscope doit être relié à la terre
et une sonde différentiel devrait être utilisé en entrée. Les sondes et conducteurs doivent être
choissis avec soin pour effectuer les meilleures mesures à l’aide d’un oscilloscope. Voir le
manuel d’instruction pour une utilisation correcte des instruments.
Fire and Explosion Hazard:
Fires or explosions might result from mounting Drives in hazardous areas such as loca-
tions where ammable or combustible vapors or dusts are present. Drives should be
installed away from hazardous areas, even if used with motors suitable for use in these
locations.
Risque d’incendies et d’explosions: L’utilisation des drives dans des zônes à risques (pré-
sence de vapeurs ou de poussières inammables), peut provoquer des incendies ou des
explosions. Les drives doivent être installés loin des zônes dangeureuses, et équipés de
moteurs appropriés.

AFE200 • Instruction Manual 9
1.4 Instruction for compliance with UL Mark (UL require-
ments), U.S. and Canadian electrical codes
Short circuit ratings
AFE200 must be connected to a grid capable of supplying a symmetrical short-
circuit power of less than or equal to “xxxx A rms.
The values of the “xxxx” A rms short-circuit current, in accordance with UL require-
ments (UL 508 c), for each power rating (AFE output in the manual) are shown in
the table below.
Short current rating
AFE output (kW) SCCR ( A ) up to 600Vac
1,1...37,3 5000
39....149 10000
150....398 18000
299.....447 30000
448-671 42000
672-1193 85000
≥1194 100000 ... 200000
Note! Drive will be protected by semiconductor Fuse type as specified in the instruction manual.
Branch circuit protection
In order to protect AFE against over-current use fuses specied in par. 11.1.
Environmental condition
The AFE has to be considered “Open type equipment”. Max surrounding air tem-
perature equal to 40°C. Pollution degree 2.
Wiring of the input and output power terminals
Use UL listed cables rated at 75°C and round crimping terminals. Crimp terminals
with tool recommended by terminal manufacturer.
Field wiring terminals shall be used with the tightening torque specied in par.
5.1.1.
Over-voltage control
In compliance with CSA-requirements Overvoltage at mains terminal is achieved
installing an overvoltage protection device as for :
Type OVR 1N 15 320 from ABB or similar.
Minimum time required for safe DC-link voltage
Before removing AFE cover in order to access internal parts, after mains discon-
nection wait for time as follow :
Drive size Safe time ( sec )
size 3.....5 300
size 6...7 and Parallels 300

10 AFE200 • Instruction Manual
2 - Introduction to the product
AFE200 is the series of AC/DC Active Front End (AFE) regenerative, DC Bus
power supply units
With a powerful 32-bit technology platform and reliable IGBT power stage the
AFE200 offers signicant advantages for single or multi-inverter automation sys-
tems powered by a common DC bus.
AFE200 is intended to power the ADV200..-DC fed family of AC inverters, either
single module or multi-modules with their DC buses tied in parallel.
It may also be used to supply ADV200-...-IT series intended to be powered from a
DC input.
About use with standard products (i.e. ADV200...-4 or -6) or other brand products.
AC fed inverters may utilize input lter capacitors that exist from the input diode bridge
to ground. These capacitors are subject to failure if the product is powered via the DC
bus input.
In this scenario, the input lter capacitors should be removed before powering up the
unit from an AFE...
For GEFRAN legacy or AC fed units, please consult the factory.
For Other Brand products, consult the manufacturer of that product.
Note! In order to work properly, an external LCL type line input filter and precharge kit is needed.
LCL filters must be chosen based on the overload required for the AFE: Heavy Duty or Low Duty.
Connection with Precharge Kit and LCL Filter
D
C
AC Main
Supply
EMI Filter
LR3-AFE
K2M
K1M
LC-AFE
PRECHARGE SECTION
LCL Input Filter
M
E
C
Exp-Sync-ADV
SMPS and
power interface
+
Control signals
Exp-Enc-ADV
SMPS and
power interface
C+
Encoder signals
Control board Control board
AFE200 ADV200-DC
C (+)D (-)
Reduced operating costs
The AFE200 achieves considerable savings in terms of power consumption
and the relative costs. The kinetic energy of the inertia of the loads transformed
into electric energy by the AFE200 is sent back to the mains supply during
Caution

AFE200 • Instruction Manual 11
braking. In conventional resistor braking systems this power is dissipated in the
form of heat. The excess energy can be used to supply other equipment.
Production of Clean Power
The regeneration technology of the AFE200 uses advanced control algorithms to
provide clean power. A signicant reduction in harmonic distortion (less than
3% considering an AC main supply with THD voltage lower than 2%) and the input
current in phase with the input voltage enable unitary power factor operation,
for additional energy saving and system efciency.
Enhanced control dynamics
Used in single or multi-inverter solutions powered by a common DC bus the
AFE200 also guarantees high-level control dynamics in AFE and energy regen-
eration conditions, which would be impossible with electric braking solutions.
Control and monitoring performed on the DC-link also prevent the risk of undesir-
able stoppages during power transients and make the AFE200 a reliable solution
for use in networks with high voltage uctuation levels.
Typical applications
The AFE200 is ideal for applications that require management of high-inertia loads
or with high operating dynamics, such as: test benches, industrial lifting applica-
tions, centrifuges, mixers, ventilation systems, renewable energy systems, rolling
systems, high-power servo systems, etc.
The economic benets of using the AFE200 in applications such as these are not
of secondary importance.

12 AFE200 • Instruction Manual
2.1 Product type designation
The main technical characteristic of the AFE200 are showed in the product code
and in the nameplate.
AFE200 3 200 -K X X -4 -XX YY
Parallel version only:
XX : MS = MASTER
SL = SLAVE with MS/SL cable 1m length
SL2 = SLAVE with MS/SL cable 2m length
YY : 04 = 400.0 kW
05 = 500.0 kW
06 = 630.0 kW
07 = 710.0 kW
09 = 900.0 kW
10 = 1 MW
14 = 1.35 MW
17 = 1.65 MW
Rated voltage (factory setting):
4= 400 Vac, 50 Hz
6 = 500...690 Vac
Software: X = standard
Braking unit:
X = not included B = included
Keypad:
X = non included K = included
Power, in kW:
200 = 22.0 kW
450 = 45.0 kW
900 = 90.0 kW
1100 = 110.0 kW
1320 = 132.0 kW
1600 = 160.0 kW
2000 = 200.0 kW
2500 = 250.0 kW
3150 = 315.0 kW
3550 = 355.0 kW
Mechanical sizes:
3 = size 3
4 = size 4
5 = size 5
6 = size 6
7 = size 7
Active Front End Regenerative Power Supply Unit
Identication Nameplate
Type : AFE200-3220 -KXX-4 S/N: 09012345
Inp: 400Vac -15% ÷ 500 Va c +5% 50/60 Hz 3ph
40A@400Vac 36A@480Vac
Out : 650Vdc-780Vdc
28kW 43A @650Vdc 39A @780Vdc Ovld.150% -60s
42kW 64A @650Vdc 57A @780Vdc Ovld.110% -60s
Model
Serial number
Input (mains supply)
Output (Output voltage, power,
current, CT and VT overloads)
Approvals
Gefran S.p.Avia G.Carducci, 24
I-21040-Gerenzano, VA
Firmware & cards revision level nameplate
Firmware HW release S/N 09012345 Prod.
Release DFPRSBUSW.CFG CONF
0.8.0 A -.G -.I 10.10.10 A1
Power
Regulation
Safety
Braking unit
Software
revision
Product
configuration
Cards revision
Firmware revision
The choice of AFE200 depends on the power rating of the inverters connected to
the DC-link.

AFE200 • Instruction Manual 13
The rated output current of the AFE200 must be higher or equal to the sum of the
power ratings of the AFE200 connected to the DC-link. For further information
please see Appendix 1.
(*) The power rating in kW shown on the product data plate refers to that of the equivalent ADV200-DC.
2.1.1 Parallel congurations
A parallel connection of several units basically consists of one MASTER unit and
one or more SLAVE units.
When placing your order please give the code number of the master and slave
and number of these:
Power code Description (Designation) Power code Description (Designation)
400kW S9AF21M AFE200-72000-KXX-4-MS 04 400kW S9AF51M AFE200-72000-KXX-6-MS 04
S9AF21S AFE200-72000-XXX-4-SL S9AF51S AFE200-72000-XXX-6-SL
500kW S9AF22M AFE200-72500-KXX-4-MS 05 500kW S9AF52M AFE200-72500-KXX-6-MS 05
S9AF22S AFE200-72500-XXX-4-SL S9AF52S AFE200-72500-XXX-6-SL
630kW S9AF23M AFE200-73150-KXX-4-MS 06 630kW S9AF53M AFE200-73150-KXX-6-MS 06
S9AF23S AFE200-73150-XXX-4-SL S9AF53S AFE200-73150-XXX-6-SL
710kW S9AF24M AFE200-73550-KXX-4-MS 07 710kW S9AF54M AFE200-73550-KXX-6-MS 07
S9AF24S AFE200-73550-XXX-4-SL S9AF54S AFE200-73550-XXX-6-SL
900kW
S9AF231 AFE200-73150-KXX-4-MS 09
900kW
S9AF53M1 AFE200-73150-KXX-6-MS 09
S9AF23S AFE200-73150-XXX-4-SL S9AF53S AFE200-73150-XXX-6-SL
S9AF23S AFE200-73150-XXX-4-SL S9AF53S AFE200-73150-XXX-6-SL
1MW
S9AF241 AFE200-73550-KXX-4-MS 10
1MW
S9AF54M1 AFE200-73550-KXX-6-MS 10
S9AF24S AFE200-73550-XXX-4-SL S9AF54S AFE200-73550-XXX-6-SL
S9AF24S AFE200-73550-XXX-4-SL S9AF54S AFE200-73550-XXX-6-SL
1.35MW
S9AF54M4 AFE200-73550-KXX-6-MS 14
S9AF54S AFE200-73550-XXX-6-SL
S9AF54S AFE200-73550-XXX-6-SL
S9AF54S2 AFE200-73550-XXX-6-SL2
1.65MW
S9AF54M5 AFE200-73550-KXX-6-MS 17
S9AF54S AFE200-73550-XXX-6-SL
S9AF54S AFE200-73550-XXX-6-SL
S9AF54S2 AFE200-73550-XXX-6-SL2
S9AF54S2 AFE200-73550-XXX-6-SL2

14 AFE200 • Instruction Manual
3 - Transport and storage
Correct transport, storage, erection and mounting, as well as careful operation and
maintenance are essential for proper and safe operation of the equipment.
Protect the AFE200 against physical shocks and vibration during transport and storage.
Also be sure to protect it against water (rainfall) and excessive temperatures.
Le bon accomplissement des opérations de transport, de stockage, d’installation et de mon-
tage, ainsi que l’exploitation et l’entretien minutieux, sont essentiels pour garantir à l’appareil
un fonctionnement adéquat et sûr.
If the AFE have been stored for longer than two years, the operation of the DC link
capacitors may be impaired and must be “reformed”. Before commissioning devices
that have been stored for long periods, connect them to a power supply for two hours
with no load connected in order to regenerate the capacitors, (the input voltage has to
be applied without enabling the AFE).
En cas de stockage des AFE pendant plus de deux ans, il est conseillé de contrôler l’état
des condensateurs CC avant d’en effectuer le branchement. Avant la mise en service des
appareils, ayant été stockés pendant long temps, il faut alimenter variateurs à vide pendant
deux heures, pour régénérer les condensateurs : appliquer une tension d’alimentation sans
actionner le AFE.
3.1 General
A high degree of care is taken in packing the AFE200 product and preparing them
for delivery. They should only be transported with suitable transport equipment
(see weight data). Observe the instructions printed on the packaging. This also ap-
plieswhen the device is unpacked and installed in the control cabinet.
Upon delivery, check the following:
- the packaging for any external damage
- whether the delivery note matches your order.
Open the packaging with suitable tools. Check whether:
- any parts were damaged during transport
- the device type corresponds to your order
In the event of any damage or of an incomplete or incorrect delivery please notify
the responsible sales ofces immediately. The devices should only be stored in
dry rooms within the specied temperature ranges .
Note! A certain degree of moisture condensation is permissible if this arises from changes in temperature.
This does not, however, apply when the devices are in operation. Always ensure that there is no
moisture condensation in devices that are connected to the power supply!
Caution

AFE200 • Instruction Manual 15
3.2 Permissible Environmental Conditions
Temperature
storage �������������������� -25…+55°C (-13…+131°F), class 1K4 per EN50178
-20…+55°C (-4…+131°F), for devices with keypad
transport������������������� -25…+70°C (-13…+158°F), class 2K3 per EN50178
-20…+60°C (-4…+140°F), for devices with keypad
Air humidity
storage �������������������� 5% to 95 %, 1 g/m3to 29 g/m3(class 1K3 as per EN50178)
transport������������������� 95 % (3), 60 g/m3(4)
A light condensation of moisture may occur for a short time occasionally if the device is not in operation
(class 2K3 as per EN50178)
Air pressure:
storage �������������������� [kPa] 86 to 106 (class 1K4 as per EN50178)
transport������������������� [kPa] 70 to 106 (class 2K3 as per EN50178)
(3) Greatest relative air humidity occurs with the temperature @ 40°C (104°F) or if the temperature of the
device is brought suddenly from -25 ...+30°C (-13°...+86°F).
(4) Greatest absolute air humidity if the device is brought suddenly from 70...15°C (158°...59°F).

16 AFE200 • Instruction Manual
4 - Mechanical installation
The AFE must be mounted on a wall that is constructed of heat resistant material.
While the AFE is operating, the temperature of the AFE’s cooling ns can rise to a
temperature of 158° F (70°C).
Le AFE doit être monté sur un mur construit avec des matériaux résistants à la chaleur.
Pendant le fonctionnement du AFE, la température des ailettes du dissipateur thermique peut
arriver à 70°C (158° F).
Because the ambient temperature greatly affects AFE life and reliability, do not install
the AFE in any location that exceeds the allowable temperature.
Étant donné que la température ambiante inue sur la vie et la abilité du AFE, on ne devrait
pasinstaller le AFE dans des places ou la temperature permise est dépassée.
Be sure to remove the desicant dryer packet(s) when unpacking the AFE. (If not
removed these packets may become lodged in the fan or air passages and cause the
AFE to overheat).
Lors du déballage du AFE, retirer le sachet déshydraté. (Si celui-ci n’est pas retiré, il empêche
la ventilation et provoque une surchauffe du AFE).
Protect the device from impermissible environmental conditions (temperature, humidity,
shock etc.).
Protéger l’appareil contre des effets extérieurs non permis (température, humidité, chocs etc.).
4.1 Inclination and mounting clearance
The AFE200 must be mounted in such a way that the free ow of air is ensured
see paragraph 10.7 Cooling.
Maximum angle of inclination �����������30° (referred to vertical position)
Minimum top and bottom distance �������150 mm (≥AFE200-71600 = 400mm)
Minimum free space to the front ���������25 mm
Minimum distance between drives �������none
Minimum distance to the side with the cabinet 10 mm
10 mm [ 0.4" ]≥
≥
400 mm[15.75" ] (ADV 7...)
150 mm[6"]
≥
25 mm [ 0.98” ]≥10 mm [ 0.4" ]≥
≥150 mm[6"]
≥400 mm[15.75" ] (ADV 7...)

AFE200 • Instruction Manual 17
4.2 Fastening positions
Taglia 3
Size 3
150 [5.91”]
500.1 [19.7”]
(A)
No. 4 screw 5MA
(B)
Fissaggioamuro
Wall mounting
187.6 [7.4”]
517 [20.35”]
Taglia 4
Size 4
220 [8.66”]
612 [24.09”]
595 [23.43”]
(A)
(B)
No. 4 screw 6MA
268 [10.55”]
616 [24.25”]
267 [10.51”]
Taglia 5
Size 5
(B)
(A)
No. 4 screw 6MA
311 [12.24”]
190 [7.48”]
730.4 [28.76”]
748 [29.45”]
265 [10.43”]
Fissaggioamuro
Wall mounting
853 [33.58”]
(B)
(A)
350 [13.78”]
175 [6.89”]
275 [10.83”]
421 [16.57”]
No. 5 screw 6MA
836 [32.91”]
Taglia 6
Size 6

18 AFE200 • Instruction Manual
Taglia 7
Size 7
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
1264 [49.76”]
1209.5 [47.62”]
Fissaggioamuro
Wall mounting
(B)
(A)
6.5
[0.26”]
6.5
[0.26”]
Ø 13
[0.51”]
19
[0.75”]
17.45
[0.69”]
15.25
[0.6”]
(A)
(B)
1407 [55.4”]
(*) Protezione in policarbonato trasparente
(*) Protective trasparent policarbonate
(*)
(*)
(B)(A)
7.25
[0.29”]
5.5 [0.21”]
5.5 [0.21”]
15
[0.59”]
Ø
10
[0.39”]
11.25
[0.44”]
6.5 [0.26”]
Ø
13
[0.51”]
19
[0.75”]
6.5 [0.26”]
12.5 [0.49”]
12
[0.47”]
Taglie 1-2-3
Sizes 1-2-3
Taglia 4
Size 4
(B)(A)
Taglia 5
Size 5
(B)(A)
6.5 [0.26”]
19
[0.75”]
Ø13
[0.51”]
6.5 [0.26”]
12
[0.47”]
12.75 [0.50”]
(B)(A)
Taglia 6
Size 6
6.5 [0.26”]
6.5 [0.26”]
Ø13
[0.51”]
19
[0.75”]
24.95 [0.98”]
12
[0.47”]
Recommended screws for fastening
Size 3 (AFE 3...) 4 x M5 x 12 mm screws + Grover (spring-lock) washer + Flat washer
Size 4 (AFE 4...) Size 5 (AFE 5...) 4 x M6 x 16 mm screws + Grover (spring-lock) washer + Flat washer
Size 6 (AFE 6...) 5 x M6 x 16 mm screws + Grover (spring-lock) washer + Flat washer
Size 7 (AFE 7...) 6 x M6 x 16 mm screws + Grover (spring-lock) washer + Flat washer
Note! Other dimensions see chapter 10.8 Weight and dimensions.

AFE200 • Instruction Manual 19
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
1264
[49.76”]
1209.5
[47.62”]
Fissaggioamuro
Wall mounting
(A)
(B)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
400 ... 710 kW
(*) Protezione in policarbonato trasparente
(*) Protective trasparent policarbonate
1407
[55.4”]
(*) (*)
(*)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
1264
[49.76”]
1209.5
[47.62”]
Fissaggioamuro
Wall mounting
(A)
(B)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
900 ... 1000 kW
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
1407
[55.4”]
(*) Protezione in policarbonato trasparente
(*) Protective trasparent policarbonate
(*) (*)
(*) (*)
(*)

20 AFE200 • Instruction Manual
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
1264
[49.76”]
1209.5
[47.62”]
Fissaggio a muro
Wall mounting
(A)
(B)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
1350 kW
1407
[55.4”]
(*) Protezione in policarbonato trasparente
(*) Protective trasparent policarbonate
(*) (*)
(*)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
(*)
(*)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
(*)
(*)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
1264
[49.76”]
1209.5
[47.62”]
(A)
(B)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
1407
[55.4”]
(*) (*)
(*)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
(*)
(*)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
(*)
(*)
417 [16.42”]
177.8 [7.00”]
355.6 [140”]
(A)
(B)
(*)
(*) Fissaggio a muro
Wall mounting
1650 kW
(*) Protezione in policarbonato trasparente
(*) Protective trasparent policarbonate