GEMAR Lumitec IRIDIUM 113886 User manual

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any
prior written notice.
Arc Mini Wash -
Control Box
Please read carefully before use
User manual
Code 113886

1.Product Overview
1 18
MENU DOWN UP ENTER
POWER IN POWER OUT
DMX IN DMX OUT

10.Installation
2.Mechanical Specification
217
5.9 cm 9.7 cm
19.5 cm
M3

Cabling must have a male XLR connector on one end and a
female XLR connector on the other end.
3-PIN TO 5-PIN CONVERSION CHART
3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5 pin DMX output connector,
you need to use a 5 pin to 3 pin adapter. The chart below details a
proper cable conversion:
caution:Do not allow contact between the ground and the fixture’s
chassis ground. Grounding the ground can cause a ground loop,
and your fixture may perform erratically. Test cables with an ohm
meter to verify positive pole and to make sure the pins are not
grounded or shorted to the shield or each other.
DMX connector configuration
GROUND
Conductor
Ground/Shield
Data ( - ) signal
Data ( + ) signal
Do not use
Do not use
3 Pin Female (output)
Pin 1
Pin 2
Pin 3
5 Pin Male (Input)
Pin 1
Pin 2
Pin 3
Do not use
Do not use
9.CABLE CONNECTORS
3.Introduction
The AC02 is a control box with the light controller. Its color is
black in the plastic material. And the power supply unit is
provided by the external switching power supply. The
protection class reach the "IP20". The control box is used in the
-20°c~40°c. So, it can be installed indoor environment. AC02
has won many certifications, including the CE, ROHS, 3C and
so on. Besides, it can control the light through the console.
Power Set Up
Your cables should be made with a male and female connector
on either end of the cable. Also remember that power cable
must be daisy chained and cannot be split.
Notice: Be sure to follow figures two and three when making
your own cables.Do not use the ground lug on the XLR
connector. Do not connect the cable’s shield conductor to the
ground lug or allow the shield conductor to come in contact with
the XLR’s outer casing. Grounding the shield could cause a
short circuit and erratic behavior.
3 16

4.Technical data
● Material: Plastic
● Colour: Black
● Max Power: 5W
● Input voltage: DC 110-230V
● Control Channels: 1,3,4,7 channel
● Power supply unit: External switching power supply
● Electronically reversible: Radio Remote
● Connection: Power input and output, DNX 3 pin XLR input and
output
● Protection class: IP20
● Working temperature: -20°c~40°c
● Installation: Indoor environment
● Dimensions: 169×97×58.2mm
● N.W.: 0.6kg
415
DMX connection
Connect 40units lights with controller, set all channels are same.
AC 230V
1
POWER IN
DMX IN
POWER OUT
DMXOUT
40
POWER IN
DMX IN
POWER OUT
DMXOUT

Connect 40units lights with controller.
Press the MENU button and Up button or Down button until
or is
showed, then press ENTER. And you will see two items.
1)Same
The lights will be showed in the same effect.
2)Different
The lights will be showed in the different effects.
When the different is showed, you need select the 3 channels.
1)Press the MENU button and UP button or DOWN button until
is showed, then press ENTER.
2) now is showed, then you can press the ENTER
until "WAIT ONE FIX" is displayed.
AC 230V
8.POWER CONNECTION
Remote control
Control box connection
Connect 40units lights with controller, set one light on
, or ,
other 39 lights set it SLAVE-RUN.
1 40
POWER IN POWER OUT POWER IN POWER OUT
5.Displayer introduction
5 14
DMX Led Modes
Differet DMX Led Modes Same
RUN MODE STAT COLO AUTO
LOAD ADDRES
LOAD ADDRES
1. DMX means the light is in the DMX mode.Similarly,SLAVE
means the light is in the SLAVE mode.
2. The color of the point shows the condition of signal transmission.
Green represents the good condition, while red represents the
signal is interrupted.
3. The item shows the working temperature of the light.When the
working temperature exceeds the max temperature,the color of the
letters and number will change from white to yellow.
4. This item shows the menu you selected.
5. This item shows the condition of key lock. “Key lock open” means
the key lock is open.And “Key lock off” means the key lock is close.
①
DMX
Key lock open
temp:043
DMX
[ADDRESS ]
001
④
⑤
② ③
DOWN
9
6
3
8
5
2
7BG
W
R
4
1
STROBE
0
UP
SOUND
2
SOUND
1
SPEED
AUTO
2
AUTO
1
SLAVEDMX
AC 230V
1
POWER IN
DMX IN
POWER OUT
DMXOUT
40
POWER IN
DMX IN
POWER OUT
DMXOUT

Connect 40units lights with controller.
Press the MENU button and Up button or Down button until
or is
showed, then press ENTER. And you will see two items.
1)Same
The lights will be showed in the same effect.
2)Different
The lights will be showed in the different effects.
When the different is showed, you need select the 3 channels.
1)Press the MENU button and UP button or DOWN button until
is showed, then press ENTER.
2) now is showed, then you can press the ENTER
until "WAIT ONE FIX" is displayed.
6.Programme Menu
13 6
108 - 111
112 - 115
116 - 119
120 - 123
124 - 127
128 - 131
132 - 135
136 - 139
140 - 143
144 - 147
148 - 151
152 - 155
156 - 159
160 - 163
164 - 167
168 - 171
172 - 175
176 - 179
180 - 183
184 - 187
188 - 191
192 - 195
196 - 199
200 - 203
204 - 207
208 - 211
212 - 215
216 - 219
220 - 223
224 - 255
magenta 2
blue 2
med blue green
dark blue
bright pink
medium blue
golden amber
deep golden amber
pale lavender
apricot
dark lavender
chocolate
just blue
surprise pink
scarlet
surprise peach
fire
english rose
mauve
bright blue
alice blue
rose indigo
urban blue
cool blue
Light salmon
mayan sun
cherry rose
flesh pink
skelton exotic sangria
amber
DMX
Channel
001
Channel
003
Channel
004
Channel
007
Address
001
Address
512
Fixt Number
001
Fixt Number
073
Led Modes
Differet
Led Modes
Same
RUN MODE
DMX
SLAVE

DMX 7 channel
channel
1
2
3
4
5
6
7
value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0
1 - 255
0 - 19
20 - 23
24 - 27
28 - 31
32 - 35
36 - 39
40 - 43
44 - 47
48 - 51
52 - 55
56 - 59
60 - 63
64 - 67
68 - 71
72 - 75
76 - 79
80 - 83
84 - 87
88 - 91
92 - 95
96 - 99
100 - 103
104 - 107
function
Master dimmer
red
green
blue
strobe
Off
Different colourmacros 36
none
red
green
blue
yellow
cyan
magenta
white
orange
pink
violet
aquamarine
sky blue
full white
cool white
warm white
white 3200
white 2500
yellow 2
straw
orange 2
light rose
dark pink
7 12
STAT COLO
STAT RED
STAT GREEN
STAT BLUE
SELET COLOR
STAT STROB
SET UP
Display Led
Key locks
Leds Dimmer
RED
Leds Dimmer
GREEN
Leds Dimmer
BLUE
Leds Dimmer
ALL
INFORMATION
Software
V2.0.0
Hardware
H1.0.0
Fix times
00001h 18m
AUTO
AUTO SPEED
AUTO MODE
000
031
001
021
01
52
00
31
OFF
ON
000
255
000
255
LOAD ADDRES
RESET

DMX 1 channel
channel
1
value
0
1 - 255
function
Off
Different colourmacros 36
DMX 4 channel
channel
1
2
3
4
value
0 - 255
0 - 255
0 - 255
0 - 255
function
Master dimmer
red
green
blue
7.DMX control mode
11 8
DMX-In this menu,you can connect several pieces of lights with
DMX cable and control them with control console.
1. Press “ENTER” button and then UP or DOWN button until “DMX
” is showed.
2. Press “ENTER” button, and “CHANNEL”, “ADDRESS”, “Led
Modes” or “Fixt Number” will be showed.Then press ENTER.
1) “Channel xxx” will be showed, “x” represents the showed DMX
channel mode. You can press the UP or DOWN button to select
your desired Channel mode.
2) “ADDRESS xxx” will be showed, “x” represents the showed
address. You can press the UP or DOWN button to select your
desired address.
3) “Led Modes Differet” or “Led Modes Same” will be showed
1)Same - The lights will be showed in the same effect.
2)Different - The lights will be showed in the different effects.
4) “Fixt Number xxx” will be showed,press the UP or DOWN button
you can know the number of connection lights.
RUN MODE-In this menu, you can select DMX mode or SLAVE
mode.In SLAVE mode,you can select one light as the MASTER
light and other lights in SLAVE mode will run following the MASTER
light.
1. Press “ENTER” button and then UP or DOWN button until “RUN
MODE” is showed.
2.Press “ENTER” button, and“DMX” or “SLAVE” will be showed,
then press ENTER to select your desired mode.
SET UP-In this menu, you can adjust the value of the the function.
1. Press “ENTER” button and then UP or DOWN button until “SET
UP” is showed.
DMX 3 channel
channel
1
2
3
value
0 - 255
0 - 255
0 - 255
function
red
green
blue

9 10
2. Press “ENTER” button, and there will be six options. Then,press
ENTER to select the option and press UP or DOWN button to
select the value you desire as below.
1) Display Led - In this item,you can select “ON” or “OFF”.If you
select ON,the displayer will be on all the time.And if you select
OFF,the displayer will extinguish about ten seconds later.
2) Key locks - You can select whether the password is on or off in
this menu , and the password is [ DOWN ] + [ UP ] + [ DOWN ] + [
UP ] .If you select “on”,then you have to input the password before
pressing the buttons.Otherwise,the light won’t respond to your
order.
3) Dimmer RED - You can adjust the red brightness in this menu.
4) Dimmer GREEN - You can adjust the green brightness in this
menu.
5) Dimmer BLUE - You can adjust the blue brightness in this menu.
6) Dimmer ALL - You can adjust the brightness of each color in this
menu.
INFORMATION-In this menu, you can learn about the information
of software, hardware and the working time of the light.
1. Press “ENTER” button and then UP or DOWN button until
“INFORMATION” is showed.
2. Press “ENTER” button, and“Software” “Hardware” or “Fix times”
will be showed. Then press ENTER, and you can see three items
as below:
1) Software - This item displays the Software information.
2) Hardware - This item displays the Hardware information.
3) Fix times - This item displays the working hours about the light.
AUTO-In this menu, you can select your desire AUTO mode and
adjust the running speed.
1. Press “ENTER” button and then UP or DOWN button until
“AUTO” is showed.
2. Press “ENTER” button, and “SPEED” or “AUTO MODE” will be
showed. Then press ENTER,and you can see two items as below:
1) SPEED - You can select your desired speed in this menu.
2) AUTO MODE - You can select your desired auto mode in this
menu.
STAT COLOR-In this menu, you can adjust the value of static color
and strobe speed as you like.
1. Press “ENTER” button and then UP or DOWN button until “STAT
COLOR” is showed.
2. Press “ENTER” button, and there are six options. Then press
ENTER to select the option and press UP or DOWN button to
select the value you desire as below:
1) STAT RED - You can adjust the red brightness in this menu.
2) STAT GREEN - You can adjust the green brightness in this
menu.
3) STAT BLUE - You can adjust the blue brightness in this menu.
4) SELET COLOR -You can select 52 static color in this menu.
5) STAT STROB - You can adjust the strobe speed in this menu.
LOAD ADDRESS-In this menu, you can set the new address.
1)Press the MENU button and UP button or DOWN button until
"LOAD ADDRESS" is showed, then press ENTER.
2)"CLEAR ADDRESS" now is showed, then you can press the
ENTER until "WAIT ONE FIX" is displayed.
RESET-In this menu, you can reset all the value of the system.
1. Press “ENTER” button and then UP or DOWN button until
“RESET” is showed.
2. Press the ENTER button to reset all the value of the system.