Gemini TITAN User manual

Gemini TITAN Light
4000 Lumens
Thank you for your support and enjoy your Gemini TITAN!
To view our FAQ go to our website:
http://gemini-lights.com/support/faq
For any enquiries please contact us below:
http://gemini-lights.com/contact
Or you can email us directly at:
Product Information: [e-mail]
Customer Support: [e-mail]
Contact Information

STORAGE & HANDLING
1. Give your battery a full charge before using it for the first time.
2. Do not carry your light or battery by its cable and use the connector head to unplug cables.
3. Always store batteries in a cool, dry place and away from direct sunlight.
CHARGING
Plug the charger into an outlet and connect the charger cable to the battery.
Red indicates battery is charging.
Green indicates battery is full.
Charging time is approximately 6 hours for a 6-cell battery and 8 hours for a 8-cell battery.
For more information on proper battery care visit our website:
http://gemini-lights.com/explore/how-charge-lithium-ion-battery
Congratulations on your purchase of a Gemini TITAN! Please take a moment to get to know
your new light.
ONE YEAR WARRANTY
Your purchase is protected by Gemini Lights with a one year warranty covering any defects in
material and workmanship.
SAFETY PRECAUTIONS
1. The Gemini TITAN is extremely bright and can damage the eye. Please do not stare
directly into the beam.
2. The light is intended for outdoor use. Without adequate cooling or moving airflow,
the light can get hot, so please be careful.
3. Use only Gemini Lights chargers with Gemini Lights battery packs.
4. Please do not submerge the light underwater.
Gemini Lights accepts no liability for injuries or damage arising from the misuse of this light.
FOR MORE INFORMATION
Please visit our website for more detailed information about product usage, warranty and
battery care.
Warranty Support:
http://gemini-lights.com/support/warranty-guide
01 02

6-Cell Battery 8-Cell Battery
3. Use the built-in velcro arm to wrap the battery pack securely around your frame.
Alternatively you can place the battery pack in your back pack.
4. Connect the cable from the light head to battery. Use the extension cable provided if
necessary.
MOUNTING & INSTALLATION
Handlebar Mounting
1. Place the TITAN centered over your handlebar stem. If the light does not clear your
stem, swap out the rubber base pads for taller ones. Attach the o-ring on the TITAN’s
front hooks and wrap the rings around your handlebar to fasten to the rear hooks.
2. Use the smaller o-ring to mount the wireless remote next to your grips.
03 04

FACTORY RESET
To reset to factory default settings, press and hold the button for 10s.
Three quick flashes will confirm the change.
WIRELESS REMOTE
The button operates the ON/OFF and cycle functions for LOW, MED, HIGH.
To enter FLASH mode, start in the OFF position and press the button for 1s.
The button activates the LOW / HIGH BEAM function. When the light is ON, this feature will dim
the light continuously until the button is released. Conversely when the light is OFF, this feature
will activate high beam until the button is released. It may also be used in alerting oncoming traffic
when repeatedly pressed.
To pair one or more lights to a single remote, disconnect the lights from the battery and reconnect
them. Pressing any button on the remote will activate the pairing.
SAFETY FEATURES
Overheat Protection
The Gemini TITAN packs a lot of power in a very small package. During regular use, the light will
produce a lot of heat. It is recommended to switch to LOW mode when stationary, as the light will
get hot without adequate airflow.
For your safety, the light has an overheat protection feature built-in. If temperatures get too hot,
the light will automatically dim itself. Once the light is able to cool down, it will return to normal
operation.
Low Battery Warning
When the battery charge reaches a very low level, the button will flash red and the light will
automatically dim to low power to conserve energy.
LIGHT OPERATION
To switch the light ON, press the button.
To switch the light OFF, press the button for 1s.
To cycle through the different LOW, MED, HIGH modes, press the button repeatedly.
To enter FLASH mode, start in the OFF position and press the button for 1s.
BUTTON INDICATOR
The button on the light provides feedback on the status of your light.
Green indicates there is 100-50% battery charge remaining
Amber indicates there is 50-25% battery charge remaining
Red indicates there is 25-10% battery charge remaining
Flashing red indicates there is 10-0% battery charge remaining
Flashing amber indicates the light is in programming mode
PROGRAMMING MODES
There are 10 different brightness levels available to save as the default.
LOW, MED, HIGH, FLASH modes are all programmable.
1. Navigate to the selected mode and press the button for 3s. The light will enter
programming mode and output 10% brightness.
2. With each click of the button, the light cycles through the 10 different brightness
levels: 20 - 30 - 40 - 50 - 60 - 70 - 80 - 90 - 100% . . . 10 - 20 - 30% . . .
3. To save the brightness level and exit programming mode, press the button for 3s.
The light will turn offand on again to confirm the change.
05 06