Generac Portable Products 1313-1 User manual

GEN RAC°
Portable Products ,_
3 5 0 0WATT
Portable Generator Owner's Manual
Model No. 1313-I (3,500 Watt AC Generator) ManualNo. 18721I Revision0 (8/31/2000)
Visit our Generac website: www.generac-portables.com
This isthe safety alert symbol. It isusedto alert you to potential personal injuryhazards.
Obey all safety messagesthat follow this symbol to avoid possible injuryor death.

GeneracPortableProducts3,500WattGenerator
EQUIPMENT
DESCRIPTION
This generator is an engine-driven, revolving field,
alternating current (AC) generator. It was designedto
supply electrical power for operating compatible electrical
lighting, appliances,tools and motor loads. This manual
contains informationfor a generator that operates 120
and/or 240 Volt, single phase,60 Hz devices that require up
to 3,500 watts (3.5 kW) of power that pult up to
29.2 Amps at 120Volts or 14.6Amps at 240 Volts.
_CAUTION! Do Not exceed the generator's
wattage/amperagecapacity.Add up the rated watts
of all devicesyou are connecting to generator
receptacles at one time. This total should not be
greater than 3,500 watts. In most casesrated watts
of the electrical device canbe found on the device
nameplate. If the device nameplate givesonly volts
and amps,multiply volts times ampsto obtain watts
(volts X amps = watts).
The 3,500 watt generator hasthe following features:
• 120/240Volt, 20 Amp locking type receptacle and a
120Volt, 30 Amp locking type receptacle.
• 120Volt, 15 Amp receptacles.
• Low Oit Shutdown: Automatically shuts down the engine
if oit drops below safeoperation level.
• Four gallon overhead fuel tank with fuel gauge.
• The generator's revolving field is driven at about
3,600 rpm by a Generac Power Systems6.5 h.p.engine.
_ARNING! Do Not tamper with engine
governed speed. High operating speedsare
dangerousand increase risk of personal injury or
damageto equipment. The generator supplies
correct rated frequency and voltage only when
running at proper governed speed. Incorrect
frequency and/or voltage candamagesome
connected electrical loads. Operating at excessively
low speedsimposes a heavyload. When adequate
engine power is not availableengine life may be
shortened.
SAFETY RULES
This generator set was designedand manufactured for
specific applications. Do Not attempt to modify the unit
or use it for any application it was not designedfor. If you
haveany questions about your generator's application, ask
your dealer/distributor or consult the factory.
The manufacturer could not possibly anticipate every
circumstance that might involvea hazard. For that reason
warnings in the manualand warnings on tags or decals
affixedto the unit are not all-inclusive. If you intend to
handle,operate or service the unit by a procedure or
method not specifically recommended by the manufacturer,
first make sure that such a procedure or method will not
render this equipment unsafeor pose athreat to you and
others.
Read this manual carefully and become familiar
with your generator set. Know its applications, its
limitations and any hazards involved.
_DANGER! You must isolate the generator from
the electric utility by opening the electrical system's
main circuit breaker or main switch if this unit is
usedfor backup power. Failure to isolate the
generator from the power utility may result
in injury or death to electric utility workers
and damage to the generator due to a backfeed
of electrical energy.Whenever unit isproviding
backup power, the electric utility must be notified.
_DANGER! Generator exhaust gasescontain
DEADLY carbon monoxide gas. Carbon
monoxide, if breathed in sufficient
concentrations, can cause unconsciousness or
death. Operate this equipment outdoors where
adequateventilation isavailable.
The EmissionControl System for this generator is
warranted for standards set by the Environmental
Protection Agency. For warranty informationrefer to the
engine owner's manual.
/2

Generac Portable Products 3,500 Watt Generator
• The generator produces a very powerful voltage that can
causeserious injuryor death by electrocution. Never
touch bare wires or receptacles. Never permit a child or
any unqualified person to operate the generator.
• Never handle any kind of electrical cord or device while
standing in water, white barefoot or white hands or feet
are wet Death or serious injuryfrom electrocution may
result.
•Use a ground fault circuit interrupter (GFCI) in anydamp
or highly conductive area (such as metal decking or steel
work).
• Never useworn, bare, frayed or otherwise damaged
electrical cords with the generator. Death, serious injury
and property damagefrom electrical shock may resutt
•Gasoline is highly FLAMMABLE and its vapors
are EXPLOSIVE. Never allow smoking, open
flames, sparks or heat in the vicinity while
handling gasoline. Avoid spillinggasoline on a hot
engine.Comply with all laws regulating storage and
handling of gasoline.
•Do Not overfill the fuel tank. Always allow room for
fuel expansion. If tank is overfllled, fuel can overflow
onto ahot engine and cause a FIRE or an
EXPLOSION.
• Never store a generator with fuel in the tank where
gasolinevapors might reach an open flame, spark or pilot
light (as on a furnace, water heater, clothes dryer). FIRE
or an EXPLOSION may result.
• The unit requires an adequateflow of cooling air for its
continued proper operation. Never operate the unit inside
any room or enclosure where the free flow of cooling air
into and out of the unit might be obstructed. Allow at
least 2 feet of clearance on all sidesof generator, even
while operating unit outdoors, or you could damagethe
unit.
• Never start, or stop the unitwith electrical loads
connected to receptacles with the connected devices
turned ON. Start the engine and let it stabilize before
connecting anyelectrical loads. Disconnect all electrical
loads before shutting down the generator.
•Do Not insertanyobject through cooling slots of the
engine.You could damagethe unit or injureyourself.
•Never operate the generator:
in rain; in any enclosed compartment; when connected
electrical devices overheat; if electrical output is lost; if
engine or generator sparks; if flame or smoke is
observed while unit is running; if unit vibrates
excessively.
GROUNDING THE
G EN ERATO R
The National ElectricalCode requires that the frame and
external electrically conductive parts of this generator be
properly connected to an approved earth ground. Local
electrical codes may also require proper grounding of the
unit For that purpose, a GROUNDING WING NUT is
provided on the generator end (Figure I).
Generally, connecting a No. 12AWG (American Wire
Gauge) stranded copper wire to the grounding wing nut
and to an earth-driven copper or brass grounding rod
(electrode) provides adequate protection against electrical
shock. Be careful to keepthe grounding wire attached after
connecting the stranded copper wire. However, local codes
may vary widely. Consult with a local electrician for
grounding requirements in your area.
Properly grounding the generator helps prevent electrical
shock ifa ground fault condition exists in the generator or
in connected electrical devices. Proper grounding also helps
dissipate static electricity, whichoften builds up in
ungrounded devices.
/3

GeneracPortableProducts3,500WattGenerator
KNOW YOUR GENERATOR
Read this owner's manual and safety rules before operating your generator.
Compare the illustrationswith your generator, to familiarize yourself with the locationsof various controls and
adjustments. Savethis manualfor future reference.
Circuit Breakers (AC)
120 Volt AC, 15 Amp
Receptacles FuelTank
FuelShut-Off
Valve
120/240Volt AC,
20 Amp Receptacle
120Volt AC, 30 Amp
Receptacle
Run/Stop Switch/
EngineControls
12 Volt DC, 10Amp
Receptacle IdleControl Switch Grounding Wing Nut
12 Volt DC, I0 Amp Receptacle -- Use this receptacle
with battery chargecablesto chargea 12Volt battery.
120 Volt A¢, I5 Amp Receptacles -- May be used to
supply electrical power for the operation of 120 Volt AC,
15 Amp, single phase,60 Hz electrical lighting,appliance,
tool and motor loads.
120 Volt AC, 30 Amp Receptacle -- May be used to
supply electrical power for the operation of 120Volt AC,
30 Amp, single phase,60 Hz electrical lighting,appliance,
tool and motor loads.
120/240 Volt AC, 20 Amp Receptacle -- May be used
to supplyelectrical power for the operation of 120and/or
240 Volt AC, 20 Amp, single phase,60 Hz electrical
lighting,appliance, tool and motor loads.
Circuit Breakers (AC) -- Eachreceptacle isprovided
with a circuit breaker to protect the generator against
electrical overload. Breakers are "push to reset" type.
Fuel Shut Off Valve -- Controls fuel supply to engine.
Fuel Tank -- Capacity of 4 U.S.gallons.
Grounding Wing Nut -- Provides a tie-point for
connecting the generator frame to earth ground.
Idle Control Switch -- The idlecontrol runs the engine
at normal (high) speedswhen there isaloadpresent and
runs the engine at idle(tow) speedswhen a toadisnot
present. This feature greatly improvesfuel economy,
extends the life of the engine,and reduces engine noise.
Run/Stop Switch -- Must be in "Run" position to start
engine.Set to "Stop" to stop a running engine.
/4

GeneracPortableProducts3,500WattGenerator
INSTALL WHEEL KIT
IMPORTANT: This wheel kit is not intended for
over-the-road use.
To installyour wheel kit you need the following tools:
• Two 13mmbox, open end, or socket wrenches
Install Wheel Kit as follows:
• Placethe bottom of the generator cradle on a fiat, even
surface. Temporarily place unit on blocks to ease
assembly.
• Slideaxle through both axle mounting brackets on cradle
frame, asshown.
• Slide a wheel over the axle.
NOTE: Be sure to installboth wheelswith the air
pressure valveon the outboard side.
•Retain wheel on axle with the retaining pin.. You may acid
the fiat washer if desired.
• Repeatstep 3 and 4 to securesecond wheel.
• Remove the existing hardware from the vibration mounts
with 13mm wrench. Use the same hardware to attach
the mounting leg.
• Remove the temporary blocks.
• Center the handle bracket on generator frame at control
panel end of cradle.
• Attach handle bracket with two cap screws and two hex
nuts. Use two 13 mm wrenches to tighten hardware.
___I T4_ I'_¢r,',',',',','_IIIkvA"rAIT'_L'4]114g
Handle Assembly
\\\\
Flat Washer
Mounting Leg
J
Use Existing Fasteners
/
JamNut
/
Wheel /
Retaining Pin
/5

GeneracPortableProducts3,500WattGenerator
BEFORE STARTING THE
ENGINE
Add Oil
_ARNING! Any attempt to crank or start the
engine before it has been properly filled with the
recommended oil may result in an engine failure.
To fill your engine with oil:
•Place generator on a level surface.
• Clean area around oil fill and remove oil fill cap.
• Select the oil's viscosity grade and fill engine with oil
following the instructions given in the engine owner's
manual. Do Not overfil!!
•Install oil fill cap.
NOTE: The generator's revolving field rides on a pre-
lubricated and sealed ball bearing that requires no
additional lubrication for the life of the bearing.
_It'_=== _11Ii I_11,_'_IF I_l_l
Add Gasoline
_ANGER! Explosion Hazard! Never fillfuel tank
indoors.Never fillfuel tank when engine isrunning
or hot Do Not light a cigarette or smoke when
filling the fuel tank.
_WARNING! Do Not overfill the fuel tank.
Always allow room for fuel expansion.
• Use regular UNLEADED gasoline with the Generator
engine.Do Not use premium gasoline. Do Not mix oil
with gasoline.
• Clean areaaround fuel fill cap, remove cap.
• Add unleaded regular gasoline, slowly to fuel tank. Be
careful not to overfill. Allow about I/2" of tank space for
fuel expansion (Figure 3).
1/2" Air Space Tank
Install fuel cap and wipe up any spilled gasoline.
IMPORTANT: It is important to prevent gum deposits
from forming in essential fuel system parts such as the
carburetor, fuel filter, fuel hose or tank during storage.
Also, experience indicates that alcohol-blended fuels (called
gasohol, ethanol or methanol) can attract moisture which
leads to separation and formation of acids during storage.
Acidic gas can damage the fuel system of an engine while in
storage.
To avoid engine problems, the fuel system should be
emptied before storage of 30 days or longer. See "Storage"
on page 12. Never use engine or carburetor cleaner
products in the fuel tank or permanent damage may occur.
/6

Generac Portable Products 3,500 Watt Generator
OPERATING THE
GEN ERATO R
,_ CAUTION! Never start or stop, the engine withelectrical loads connected to the unit and with the
connected devices turned ON.
Starting the Engine
Disconnect alt electrical loadsfrom the generator. Use the
following start instruction steps by numerical order:
I. Make sure the Idle Control switch is in "Off' position.
2. Turn the fuel valve to the "On" position.
3. Set the Run/Stop switch to "Run" position (Figure 4).
4. Placethe choke lever in the "Full" choke position
(Figure5).
5B. For manualstarting, grasp the recoil handle and pull
slowly until slight resistance isfelt. Then pull rapidly
one time only to start engine.
•If engine starts, proceed to step 7.
• Ifengine fails to start, proceed to step 6.
6. Move the choke lever to "Half" choke position, and
pull recoil handle twice.
• If engine fails to start, repeat steps 4 thru 6.
7. Move choke lever to "Run" position. If enginefalters,
move choke lever to "Half" choke position until the
engine runs smoothly and then to "Run" position.
NOTE: If engine still fails to start after 3 pulls, check for
proper oil level in crankcase.This unit isequipped with a
Low Oil Shutdown System.See engine manual.
Refer to the engine owner's manual for complete
starting instructions.
• Grasp starter grip and pull slowty untilyou feel slight
resistance,then pull quickly. Easethe starter rope back
into the engine.
• When engine starts, move choke lever to "Run"
position" by sliding it all the way to the right (awayfrom
the valve cover and under the arrow).
NOTE: If engine fails to start after 3 pulls, move the choke
leverto "Half" choke position and pull starter rope again
2 times.
NOTE: If the engine still fails to start, check for proper oil
levelin crankcase.Unit isequipped with a low oil
shutdown system. Seeengine owner's manualfor
informationregarding the low oil shutdown system.
5A. For electric starting, pressstart switch on generator
cradle. To prolong the life of the starter components,
press the starter button for no more than 15 seconds,
and pausefor 30 seconds.
Connecting Electrical Loads
•Let engine stabilize and warm up for a few minutes after
starting.
• Plugin and turn on the desired 120 and/or 240 Volt AC,
singlephase,60 Hertz electrical loads.
•Do Not connect 240 Volt loadsto 120Volt receptacles.
•Do Not connect 3-phase loadsto the generator.
•Do Not connect 50Hz loadsto the generator.
•DO NOT OVERLOAD THE GENERATOR. Add up
the rated watts (or amps) of all loadsto be connected at
one time. This total should not be greater than the rated
wattage/amperagecapacity of the generator. See "Don't
Overload the Generator" on page II.
/7

Generac Portable Products 3,500 Watt Generator
Stopping the Engine
• Unplug all electrical loads from generator panel
receptacles.Never start or stop engine with electrical
devices plugged in and turned on.
• Put the idle control switch in the "Off' position.
• Let engine run at no-load for 30 secondsto stabilizethe
internaltemperatures of engine and generator.
• Move run/stop switch to "Stop:'
• Close the fuel shut-off valve.
Operating Automatic Idle Control
This switch isdesignedto greatly improve fuel economy.
When this switch is turned ON, the engine will only
run at its normal highgoverned enginespeedwhen an
electricalload is connected.When an electrical load is
removed, the enginewill run at a reduced speed. With
the switch off, the engine will run at the normal high
engine speed.Always have the switch off when
starting and stopping the engine.
Charging a Battery
_ANGER! Storagebatteries give off explosive
hydrogengaswhile recharging. This explosive
mixture will remain around the battery for a long
time after it hasbeen charged. The slightest spark
canignite the hydrogen and causean explosion. Such
an explosion canshatter the battery and cause
blindnessor other serious injury.
_DANGER! Do Not permit smoking, open flame,
sparksor anyother source of heat around a battery.
Wear protective goggles,rubber apron and rubber
gloves when working around a battery. Battery
electrolyte fluid isan extremely caustic sulfuric acid
solution that cancausesevere burns. If spill occurs,
flush area with clear water immediately.
Your generator hasthe capability of recharging a discharged
12Volt automotive or utility style storage battery. Do Not
use the unit to chargeany 6 Volt batteries. Do Not use
the unit to crank an engine havinga discharged battery.
To recharge 12 Volt batteries, proceed as follows:
•Check fluid levelin all battery cells. If necessary,add
ONLY distilled water to cover separators in battery
cells. Do Not use tap water.
• If the battery isequippedwith vent caps,make sure they
are installedand are tight.
• If necessary,cleanbattery terminals.
• Connect battery charge cableconnectorplug to panel
receptacle identified bythe words "12-VOLT D.C:'
• Connect battery charge cableclamp with red handleto
the positive (÷) battery terminal (Figure6).
12 VOLT D.C.
RECEPTACLE
+
POS NEG
12VOLTBA'R'ERY
• Connect battery charge cableclampwith black handle
to the negative (-) battery terminal (Figure6).
• Start engine. Let the engine run while battery recharges.
• When battery hascharged, shut clown engine
NOTE: Use an automotive hydrometer to test battery
state of charge and condition. Follow the hydrometer
manufacturer's instructions carefully. Generally, a battery is
considered to be at I00% state of chargewhen specific
gravity of its fluid (asmeasured by hydrometer) is 1.260or
higher.
i8

GeneracPortableProducts3,500WattGenerator
COLD WEATH ER
OPERATION
Under certain weather conditions (temperatures below
40°F [4°C] and a high dew point), your Generac generator
may experience icingof the carburetor and/or the
crankcase breather system.
In an emergency, usethe original shipping box asa
temporary shelter:
•Cut off all flaps.
• Cut out one of the long sides of the box to expose
exhaust side of unit. Ensurea minimum of two feet
clearance between open sideof box and nearest object.
• Cut appropriate slots to accessreceptacles of unit. You
may also need to cut a clearance slot for the handle.
• Start unit, then place box over it.
IMPORTANT: Remove shelter when temperature is
above 40°F [4°C].
For a more permanent shelter, build a structure that will
enclose three sidesand the top of the generator:
• Make sure entire muffler-side of generator is exposed. A
typical shelter is shown in Figure7.
•Ensure a minimum of two feet clearance between open
side of box and nearest object.
• Face exposed end away from wind and elements.
• Enclosure should hold enough heat created by the
generator to prevent icing problems.
_CAUTIONt Never run unit indoors;Do Not
enclosegeneratoranymore than shown.Remove
shelterwhentemperatures are above40°F [4°C].
RECEPTACLES
120 Volt AC, 15 Amp Receptacles
Eachof these outlets is protected against overload by
15 Amp push-to-reset circuit breakers (Figure 8).
|||
#|
|
Use each outlet to operate 120 Volt AC, 60 Hz, single
phase loads requiring 1,800 (I .8 kW) watts at 15 Amps of
current.
/9

Generac Portable Products 3,500 Watt Generator
120/240 Volt AC, 20 Amp Locking
Receptacle
Use a NEMA LI4-20 plug with this receptacle. Connect a
4-wire cord set rated for 250 Volts AC at 30 Amps (or
greater) (Figure 9). You can use the same4-wire cord if
you plan to run a 120Volt load.
4-Wire CordSet
This receptacle powers 1201240Volt AC, 60 Hz, single
phaseloads requiring up to 2,400 watts of power at
20 Amps for 120 Volts OR 3,500 watts of power (3.5kW)
at 14.6Amps for 240 Volts. The outlet is protected by a
push-to-reset circuit breaker.
120 Volt AC, 30 Amp Locking
Receptacle
Use a NEMA L5-30 plug with this receptacle. Connect a 3-
wire cord set rated for 125Volts AC at 30 Amps to the
plug (Figure 10).
3-Wire CordSet
NEMA L5-30 /_ Ground
(Green)
Neutral
120V
Hot
Use this receptacle to operate 120 Volt AC, 60 Hz, single
phase loads requiring up to 3,500 watts (3.5 kW) of power
at 29.2 Amps. The outlet is protected by a push-to-reset
circuit breaker.
_k AUTION! Although this outlet statesit hasa
120Volt, 30 Amp rating (up to 3,600watts), the
generator is only rated for 3,500 watts. Powering
loadsthat exceed the wattage/amperage capacity of
the generator candamageit or causeserious
injuries. Loadsof 120Volts powered through this
outlet should not exceed 29.2 Amps of current
/10

Generac Portable Products 3,500 Watt Generator
DON'T OVERLOAD THE
G EN ERATO R
Overloading a generator in excess of its rated wattage
capacity can result in damageto the generator and/or
connected electrical devices. Observe the following, to
prevent overloading the unit:
• Add up the total wattage of all electrical devicesto be
connected at one time. This total should NOT be
greater than the generator's wattage capacity.
• The rated wattage of lights can be taken from light bulbs.
The rated wattage of tools, appliancesand motors can
usually be found on a data plate or decal affixed to the
device.
• If the appliance,tool or motor does not givewattage,
multiply 120Volts times ampere rating to determine
watts (volts x amps = watts).
• Someelectric motors, such asinduction types, require
about three times more watts of power for starting than
for running. This surge of power lastsfor only a few
secondswhen starting such motors. Be sure you allow
for this high starting wattage when selectingelectrical
devicesto connect to your generator. First figure the
watts needed to start the largest motor. Add to that
figure the running watts of all other connected loads.
• Items in the wattage reference guide (Figure II) are
provided to help you to determine how many items the
generator canoperate at one time.
Recreational/Home Uses
Tool/Appliance .................................................... Watts
AM/FM clock radio.....................................................................50
Lightbulb....................................................................................100
Fan................................................................................................200
20"color TV..............................................................................400
*Deep freezer............................................................................500
Personalcomputer and 15"monitor ...................................800
*1/3 hp furnace fan blower.....................................................800
Microwave oven........................................................................800
*18 cuftrefrigerator ...............................................................800
Sumppump..............................................................................1000
Electric skillet..........................................................................1250
*Y2hp water well pump........................................................1400
* 12,000Btu window air conditioner .................................1400
Spaceheater............................................................................1800
Electric water heater.............................................................4000
Professional/C ontractor Uses
Tool/Appliance .................................................... Watts
"1/3 hp airlesssprayer.............................................................600
3/8" hammerdrill.....................................................................600
VariablespeedSawzalt®..........................................................960
V2"power drill.........................................................................1000
Quartz-halogenwork light...................................................1000
Beltsander...............................................................................1200
7¼" circularsaw ...................................................................1500
7¼" worm drivesaw............................................................1600
*1Y2hp air compressor ........................................................1800
* I0" power miter saw...........................................................1800
6" bench grinder .....................................................................1800
"6" table planer.......................................................................1800
*10" table/radial arm saw .....................................................2000
Wire feed welder ...................................................................2400
* allow 3 times listed watts for starting this device
/II

Generac Portable Products 3,500 Watt Generator
SPECIFICATIONS
Maximum SurgeWatts .............. 4,375 watts
Continuous Wattage Capacity ........ 3,500 watts
Power Factor ..................... 1.0
Rated Maximum Continuous Load
At 120Volts ................... 29.2 Amps
At 240 Volts ................... 14.6Amps
Phase ........................... I phase
Rated Frequency .................. 60 Hertz
FuelTank Capacity ................. 4 U.S.gallons
GENERAL MAINTENANCE
RECOMMENDATIONS
The Owner/Operator is responsible for making sure that
all periodic maintenance tasks are completed on atimely
basis;that all discrepancies are corrected; and that the unit
is kept clean and properly stored. Never operate a
damaged or defective generator.
Engine Maintenance
See engine manualfor instructions.
Generator Maintenance
Generator maintenance consists of keeping the unit clean
and dry. Operate and store the unit in a clean dry
environment where it wit{ not be exposed to excessive
dust, dirt, moisture or any corrosive vapors. Cooling air
slots in the generator must not become clogged with snow,
leaves or any other foreign material.
NOTE: Do Not use a garden hose to clean generator.
Water can enter engine fuel system and cause problems. In
addition, if water enters generator through cooling air
slots, some of the water will be retained in voids and
cracks of the rotor and stator winding insulation. Water
and dirt buildup on the generator internal windings wit{
eventually decrease the insulation resistance of these
windings.
To Clean the Generator
•Use a damp cloth to wipe exterior surfaces clean.
• Soft, bristle brush may be used to loosen caked on dirt
or oil.
• A vacuum cleaner maybe usedto pick up loose dirt and
debris.
• Low pressure air (not to exceed 25 psi) may be used to
blow awaydirt. Inspect cooling air slots and opening on
generator. These openingsmust be kept cleanand
unobstructed.
STORAGE INSTRUCTIONS
The generator should be started at least once every seven
daysand allowed to run at least 30 minutes. If this cannot
be done and you must store the unit for more than 30
days,usethe following guidelines to prepare it for storage.
Generator Storage
•Cleanthe generator asoutlined in "To Clean the
Generator"
• Check that cooling air slots and openingson generator
are open and unobstructed.
_ii DANGER! Storagecovers can be flammable. Do
Not placea storage cover over a hot generator. Let
the unit cool for asufficient time before placingthe
cover on the unit.
Engine Storage
Seeengine owner's manualfor instructions.
Other Storage Tips
•Do Not store gasoline from one season to another.
• Replace your gasoline can if it starts to rust. Rust and/or
dirt in a gasoline can cause problems when you use
contaminated fuel with this unit.
• Store in clean and dry area.
/12

Generac Portable Products 3,500 Watt Generator
TROUBLESHOOTING
Problem
Engine isrunning, but no AC
output is available.
Engine runs good but bogs
down when loads are
connected.
Engine will not start; or starts
and runs rough.
Engine shuts down during
operation.
Engine lacks power.
Engine "hunts" or falters.
Cause
I. Circuit breaker is open.
2. Poor connection or defective
cord set.
3. Connected device is bad.
4. Fault in generator.
I. Short circuit in aconnectedload.
2. Generator isoverloaded.
3. Enginespeedistoo stow.
4. Shorted generator circuit.
I. Run/Stop switch set to "Stop".
2. Dirty air cleaner.
3. Out of gasoline.
4. Stalegasoline.
5. Sparkplug wire not connected to
spark plug.
6. Bad spark plug.
7. Water ingasoline.
8. Overchoking.
9. Low oil level.
10. Excessivelyrich fuel mixture.
I. Intakevane stuck open or closed.
12. Enginehaslostcompresslon.
Solution
I. Resetcircuit breaker.
2. Check and repair.
3. Connect another devicethat isin good
condition.
4. Contact Generac service facility.
I. Disconnect shorted electrical load.
2. See"Don't Overload the Generator" on
page II.
3. Contact Generac service facility.
4. Contact Generac service facility.
I. Setswitch to "Run".
2. Clean or replaceair cleaner.
3. Fillfuel tank.
4. Drain gastank and fill with fresh fuel.
5. Connect wire to spark plug.
6. Replacespark plug.
7. Drain gastank; fill with fresh fuel.
8. Put choke lever to "no choke" position.
9. Fill crankcaseto proper level.
10. Contact Generac service facility.
I I. Contact Generac service facility.
12. Contact Generac service facility.
I. Out of gasoline.
2. Low oil level.
3. Fault in engine.
I. Load is too high.
2. Dirty air filter.
3. Engine needs to be serviced.
I. Choke is opened too soon.
2. Carburetor is running too rich or 2.
too lean.
I. Fillfuel tank.
2. Fill crankcaseto proper level.
3. Contact Generac service facility.
I. See "Don't Overload the Generator" on
page II.
2. Replace air filter.
3. Contact Generac service facility.
I. Move choke to halfway position till
engine runs smoothly.
Contact Generac service facility.
/13

GeneracPortableProducts3,500WattGenerator
ID_ELF_i_I_
ELECTRICAL SCHEMATIC
3
w
LOP
SWITCH
[
3PARK
PLUG ENG
IGNITION
BATTERY CHARGE
BRN BLK
66 55
RED BLK
AUTO 13 55
RESET
IOA
CB
BRN
77
I
CB
_d WOJ
LdOJ 0_
O_OJ LD_
W
O/ _ LdCd
\ OrOJ
I •
RED
GRN
• 0 wOJ
S
F H
E
D •
D
G
A
E
s
G
N
A
l) _ c
CB
/14

Generac Portable Products 3,500 Watt Generator ID_'! _
WIRING DIAGRAM
BLU
11
GRY
44A RED
22 GRN
0
BLU
llB RED
u©
GRY 120V/15A
GRN
0
RED
13
RED
13
IDLE CONTROL
TRANSFORMER
GRY
BOARD
RE]]
BATTERY
CHARGE
RECTIFIER
GATE 3 PIN
SIGNAL CONNECTOR
ON ENGINE
p_
LOW OIL
PRESSURE
SWITCH
LOW OIL
PRESSURE
LED
NUT ON ENGINE _LOCK
I15

I
j/_ I
Generac Portable Products 3,500 Watt Generator
EXPLODED VIEW - MAIN UNIT
52
63
5O
10
54
_"--_--55
DETAIL "X "
3\
SEE
DETAIL "Y"
/
32
36
I
62 8
11
6
39 26 65 D_AIL
30 38 37 15 66
5
2O
_13
12
I
13
DETAIL "Y "
/16

Generac Portable Products 3,500 Watt Generator
I
f/_ I
PARTS LIST
Item Part# Qty
I G93199
2 G84021
3 NSP
4 66365
5 84141J
6 83540J
7 65791
8 96796
10 86307 4
II 47480 I
12 84508 2
13 52858 8
14 83208 I
15 DB4986 I
16 66476 2
17 89476 I
18 70644 I
19 84346 3
20 40976 2
21 83083 I
22 83071 I
23 81917 I
25 668258 I
26 85652 2
27 67989 2
30 74908 4
32 86308 4
33 65795 I
34 66849A I
35 67022 I
36 84132 I
37 66386 I
38 66849 2
39 84871 I
41 86494 I
- MAIN UNIT
Description
CRADLE, XL
SUPPORT,Engine
ENGINE, 6.5 HP XL
HOUSING, EngineAdapter
ASSEMBLY,Rotor
ASSEMBLY,Stator
BEARING
WASHER, M8 Flat
SCREW,6/16-24 x 3/4 HHM
SCREW,5/16-24 x 7" Cap
MOUNT, 45° Vibration
NUT, M8 Locking
BRACKET,Muffler
DECAL, Ground
SCREW,M6 - 1.0x 12
GASKET, Exhaust
SCREW, M8-1.25 x 20 PPHM
SCREW, M8 x 35 PPHM
SCREW,M8 - 1.25x 20
SCREEN,Spark Arrest
MUFFLER
PIN, M4 x 10 Roll
CARRIER, Rear Bearing
MOUNT, Vibration
NUT, M8 FlangeSerrated
MS-8.0 x 10 Taptite
BOLT, M6-1.0 x 115 Stator
RECTIFIER,Battery Charge
MS-0.7 x 20 Taptite
GROMMET, Rubber
MODULE, Drive
ASSEMBLY,Brush Holder
M5-0.7 x 16 Taptite
COVER, Bearing Carrier
SCREW,M6-1.0 x 16ramWing
Item
42
43
44
46
47
48
49
50
51
52
$3
54
Part # Qty
86292
77395
83465
78831B
80270
78299
85134
88325
884042
84687
85000
14353621
55 23762
56 26850
60 B4356
61 92982
62 B4357
63 93826
64 BI432
65 20566
66 77816
67 B2153
68 84409
Items Notlllustrated
65787 I
B4354 I
BB3061 I
43483 I
37806 I
Optional Accessories
84883
84895
Description
HHCS, 10-16 x 3/4" Self Drill
NUT, M6 Flange Lock
GROMMET, Tank
SCREW, M6- I .(3x 60 (black)
VALVE, Tank
BUSHING, Plastic Tank
GAUGE, Fuel Cap
TANK, Fuel
SHIELD, Heat
INSULATION, #2 I/4"
CLIP, Insulation
WIRE, Ground
WASHER, # I0 Shakeproof
WASHER, M6 Shakeproof
DECAL, Control Panel
DECAL, Danger
DECAL, Heat Shield
DECAL, Start Instruction
ASSEMBLY, Control Panel
DECAL, GENERAC 1-800#
DECAL, Caution Hot Muffler
HHCS, 12-14 x 7/8" Self Drill
SLEEVING, Flexo, HW 1/2" X
.83 ft.
Battery Charge Cable
Owner's Manual
Oil, 28 oz.
120/240Volt 20 Amp Plug
120 Volt 30 Amp Plug
Not Included:
Ext. Cord Wrap
StorageCover
w17

I
? j/_ I
Generac Portable Products 3,500 Watt Generator
EXPLODED VIEW /PARTS LIST - CONTROL PANEL
1
\\\\
8
18
8
_7 11 17
15
17
24
\
17
10
Item
I
2
3
4
5
6
7
8
9
10
II
12
Part#
BI431
83975
66818
66821
68867C
68868C
75207A
75207G
82538
84134
83514
83970
Qty Description
PANEL,Control
BOX, Control
OUTLET 120Volt AC
OUTLET 12Volt DC
OUTLET 120/240Volt, 20 Amp
Locking
OUTLET, 120Volt, 30 Amp
Locking
CIRCUIT BREAKER,30 Amp
CIRCUIT BREAKER,18 Amp
SWITCH, On/Off Rocker
GROMMET, Rubber
CIRCUIT BREAKER,10 Amp
CONTROL BOARD, System
Item
13
14
15
16
17
18
19
21
22
23
24
25
26
Part#
84028
67022
85584
84543A
84543C
84198
84197
75476
22264
51715
84543B
84335
82542
Qty Description
I TRANSFORMER, Idle Control
I GROMMET, Rubber
I BAR, Bus
2 SCREW,3.0 x 12mm
9 SCREW,3.5 x 18mm
3 SHIELD,Circuit Breaker
I BAR, Circuit Breaker Retaining
2 SCREW,4.15 x 16mm
4 WASHER, M4 Lock
4 NUT, M3 Hex
10 SCREW,3.5 x 12mm
I WIRE HARNESS
I BAR, DC Outlet Retaining
/18

Generac Portable Products 3,500 Watt Generator
I
Ill
m
EXPLODED VIEW AND PARTS LIST - WHEEL KIT
1
\\\\\
8
7
USE EXISTIN8 FASTENERS
TQ SECURE ITEbl #8
Item Part # Qty Description
I B4217 I ASSEMBLY,Handle
2 BI764 I LEG, Mounting
3 52858 2 NUT, Locking Hex M8 - 1.25
4 39287 2 HHCS, M8 - 1.25x 45
5 93693F I AXLE
6 B4966 2 WHEEL, 10"Diameter
7 87005A 2 PIN, Retaining
8 22247 2 WASHER, Flat
/19

LIMITED WARRANTY
FOR "GN" ENGINE DRIVEN PORTABLE GENERATORS
GENERAC PORTABLEPRODUCTS (hereafter referred to asthe COMPANY) warrants to the original purchaser that the
alternator and control panel for itsportable generator wilt be free from defects in materials or workmanship for the items
and period set forth below from the date of original purchase.This warranty isnot transferable and appliesonly to portable
generators driven by a GN-Series engine.
Consumer* Commercial*
Alternator 2 years (2ridyear parts only) I year
Engine Warranted solely by the engine manufacturer
With the exception of European Community Countries, all unitsbound for export shall be warranted for One (I)
Yearin Consumer applications, end 90 daysin Commercial applications as defined below.
*NOTE: For the purpose of this warranty "consumer use" means personal residential household use by
original purchaser. This warranty does not apply to units used for Prime Power in place of utility.
"Commercial Use" means all other uses, including rental, construction, commercial and income producing
purposes. Once a generator has experienced commercial use, it shall thereafter be considered a
commercial use generator for the purposes of this warranty.
During saidwarranty period, the COMPANY wilt, at isoption, repair or replace anypart which, upon examination bythe
COMPANY, isfound to be defective under normal useand service**. Starting batteries are not warranted by the
COMPANY. All transportation costs under warranty, includingreturn to the factory ifnecessary,are to be borne bythe
purchaser and prepaid by the purchaser.This warranty does not cover normal maintenanceand service anddoes not apply
to a generator set,alternator, or parts which havebeen subjected to improper or unauthorized installation or alteration,
misuse, negligence,accident, overloading, overspeeding,improper maintenance, repair or storage so as,in the COMPANY's
judgement, to adverselyaffect its performance and reliability.
**NORMAL WEAR: As with all mechanical devices, the generator need periodic parts service and
replacement to perform well. This warranty will not cover repair when normal use has exhausted the life of
a part or generator.
THEREIS NO OTHER EXPRESSWARRANTY. THE COMPANY HEREBYDISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THOSE OF MERCHANTABILITY AND
FITNESSFOR A PARTICULAR PURPOSETO THE EXTENT PERMITTED BY LAW. THE DURATION OF
ANY IMPLIEDWARRANTIES WHICH CANNOT BEDISCLAIMED ISLIMITED TO THE TIME PERIODAS
SPECIFIEDIN THE EXPRESSWARRANTY. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL
DAMAGES UNDER ANY AND ALL WARRANTIES ISEXCLUDED. THE COMPANY ALSO DISCLAIMS
ANY RESPONSIBILITYFOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,SUCH AS THE LOSSOF
TIME OR THE USEOF THE POWER EQUIPMENT, OR ANY COMMERCIAL LOSS DUE TO THE FAILURE
OF THE EQUIPMENT: AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS
WRITTEN WARRANTY.
Some states do not allow limitations on how long an impliedwarranty lasts,or the exclusion or limitation of incidentalor
consequential damages,sothe abovelimitationsor exclusions may not applyto you. This warranty givesyou specific legal
rights andyou may also haveother rights, which vary from state to state.
For service, seeyour nearest COMPANY authorized warranty service facility or call 1-877-544-0982.Warranty service can
be performed only by a COMPANY authorized service facility.This warranty will not apply to service at any other facility.
At the time of requesting warranty service, evidence of original purchasedate must be presented.
GENERAC Portable Products
Jefferson, Wisconsin 53549