Generac Portable Products 9719-3 User manual

Model No. 97193 (5,000 Watt AC Generator) Manual No. B4468 evision 3 (7/11/2000)
Visit our Generac website: www.generac-portables.com
Problems?
Questions?
Before taking your unit
back to the store,
call the generator
helpline at
1-800- 70-1408
M-F 8-5 CT
SVP5000
Portable Generator Owner’s Manual
DANGER! This generator is designed for outdoor use only. Never use this generator inside any building
or enclosure including the generator compartment of a recreational vehicle ( V). Carbon monoxide
poisoning, fire and/or an explosion may result. No user performed modifications, including venting of
exhaust and/or cooling ventilation, will eliminate the danger. Always have at least two feet of clearance on
all sides of the generator even while operating the unit outdoors.
DANGER! You must isolate the generator from the electric utility by opening the electrical systems main
circuit breaker or main switch if this unit is used for backup power. Failure to isolate the generator from
the power utility may result in injury or death to electric utility workers and damage to the
generator due to a backfeed of electrical energy.
The Emission Control System for this generator is warranted for standards set by the
Environmental Protection Agency. For warranty information refer to the engine owners manual.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.

Generac Portable Products SVP5000 Generator
2
EQUIPMENT DESCRIPTION
This generator is an engine-driven, revolving field,
alternating current (AC) generator. It was designed to
supply electrical power for operating compatible
electrical lighting, appliances, tools and motor loads.
This manual contains information for a generator that
operates 120 and/or 240 Volt, single phase, 60 Hz
devices that require up to 5,000 watts (5.0 kW) of
power that pull up to 41.7 Amps at 120 Volts or
20.8 Amps at 240 Volts.
CAUTION! Do Not exceed the generators
wattage/amperage capacity. Add up the rated
watts of all devices you are connecting to
generator receptacles at one time. This total
should not be greater than 5,000 watts. In most
cases rated watts of the electrical device can be
found on the device nameplate. If the device
nameplate gives only volts and amps, multiply
volts times amps to obtain watts
(volts X amps = watts).
The SVP5000 generator has the following features:
 120/240 Volt AC, 20 Amp locking receptacle.
 120 Volt AC, 30 Amp locking receptacle.
 120 Volt, 20 Amp duplex receptacle.
 Low Oil Shutdown: Automatically shuts down the
engine if oil drops below safe operation level.
 Five gallon overhead fuel tank.
 The generators revolving field is driven at about
3600 rpm by a Briggs & Stratton 10HP engine.
DANGER! Do Not tamper with engine
governed speed. High operating speeds are
dangerous and increase risk of personal injury
or damage to equipment. The generator
supplies correct rated frequency and voltage
only when running at proper governed speed.
Incorrect frequency and/or voltage can damage
some connected electrical loads. Operating at
excessively low speeds imposes a heavy load
at such reduced speeds, when adequate
engine power is not available, and may shorten
engine life.
SAFETY RULES
This generator set was designed and manufactured
for specific applications. Do Not attempt to modify the
unit or use it for any application it was not designed
for. If you have any questions about your generators
application, ask your dealer or consult the factory.
The manufacturer could not possibly anticipate every
circumstance that might involve a hazard. For that
reason warnings in the Manual and warnings on tags
or decals affixed to the unit are not all-inclusive. If you
intend to handle, operate or service the unit by a
procedure or method not specifically recommended by
the manufacturer, first make sure that such a
procedure or method will not render this equipment
unsafe or pose a threat to you and others.
Read this manual carefully and become familiar
with your generator set. Know its applications, its
limitations and any hazards involved.
 The generator produces a very powerful voltage that
can cause extremely dangerous electrical shock.
Avoid contact with bare wires, terminals, etc. Never
permit an unqualified person to operate or service
the generator.
Never handle any kind of electrical cord or device
while standing in water, while barefoot or while
hands or feet are wet. Dangerous electrical shock
may result.
 The National Electric Code requires the frame and
external electrically conductive parts of the
generator be properly connected to an approved
earth ground. Local electrical codes may also
require proper grounding of the generator. Consult
with a local electrician for grounding requirements in
your area.
 Use a ground fault circuit interrupter in any damp or
highly conductive area (such as metal decking or
steel work).
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, or other reproductive harm.
WARNING:

Generac Portable Products SVP5000 Generator
3
Do Not use worn, bare, frayed or otherwise
damaged electrical cord sets with the generator.
Using a defective cord set may result in electrical
shock or damage to equipment and/or property.
 Operate unit only on level surfaces and where it will
not be exposed to excessive moisture, dirt, dust or
corrosive vapors.
 Gasoline is highly FLAMMABLE and its vapors are
EXPLOSIVE. Do Not permit smoking, open flames,
sparks or heat in the vicinity while handling gasoline.
Avoid spilling gasoline on a hot engine. Comply with
all laws regulating storage and handling of gasoline.
Do Not overfill the fuel tank. Always allow room for
fuel expansion. If tank is overfilled, fuel can overflow
onto a hot engine and cause FI E or EXPLOSION.
Never store a generator with fuel in the tank where
gasoline vapors might reach an open flame, spark or
pilot light (as on a furnace, water heater, clothes
dryer). FI E or an EXPLOSION may result.
 Generator exhaust gases contain DEADLY carbon
monoxide gas. This dangerous gas, if breathed in
sufficient concentrations, can cause
unconsciousness or even death. Operate this
equipment only in the open air where adequate
ventilation is available.
 The unit requires an adequate flow of cooling air for
its continued proper operation. Never operate the
unit inside any room or enclosure where the free
flow of cooling air into and out of the unit might be
obstructed. Allow at least 2 feet of clearance on all
sides of generator or you could damage the unit.
ead Cold Weather Operation on page 7.
Never start or stop the engine-generator with
electrical loads connected to receptacles with the
connected devices turned ON. Start the engine and
let it stabilize before connecting any electrical loads.
Disconnect all electrical loads before shutting down
the generator.
Do Not insert any object through cooling slots of the
engine-generator. You could damage the unit or
injure yourself.
 Never operate the generator:
in rain; in any enclosed compartment; when
connected electrical devices overheat; if electrical
output is lost; if engine or generator sparks; if flame
or smoke is observed while unit is running; if unit
vibrates excessively.
GROUNDING THE
GENERATOR
The National Electrical Code requires that the frame
and external electrically conductive parts of this
generator be properly connected to an approved earth
ground. Local electrical codes may also require proper
grounding of the unit. For that purpose, a
G OUNDING WING NUT is provided on the
generator end (Figure 1).
Generally, connecting a No. 12 AWG (American Wire
Gauge) stranded copper wire to the grounding wing
nut and to an earth-driven copper or brass grounding
rod (electrode) provides adequate protection against
electrical shock. Be careful to keep the grounding wire
attached after connecting the stranded copper wire.
However, local codes may vary widely. Consult with a
local electrician for grounding requirements in your
area.
Properly grounding the generator helps prevent
electrical shock if a ground fault condition exists in the
generator or in connected electrical devices. Proper
grounding also helps dissipate static electricity, which
often builds up in ungrounded devices.
Figure 1  Grounding Wing Nut
Grounding Wing Nut

Generac Portable Products SVP5000 Generator
4
1 0 Volt AC, 0 Amp Duplex Receptacle  May be
used to supply electrical power for the operation of
120 Volt AC, 20 Amp, single phase, 60 Hz electrical
lighting, appliance, tool and motor loads.
1 0 Volt AC, 30 Amp Receptacle  May be used to
supply electrical power for the operation of 120 Volt
AC, 30 Amp, single phase, 60 Hz electrical lighting,
appliance, tool and motor loads.
1 0/ 40 Volt AC, 0 Amp Receptacle  May be
used to supply electrical power for the operation of
120 and/or 240 Volt AC, 20 Amp, single phase, 60 Hz
electrical lighting, appliance, tool and motor loads.
Circuit Breakers (AC)  Each receptacle is provided
with a circuit breaker to protect the generator against
electrical overload. Breakers are "push to reset" type.
Fuel Shut Off  Controls fuel supply to engine.
Fuel Tank  Capacity of 5 U.S. gallons (19 liters).
Grounding Wing Nut  Provides a tie-point for
connecting the generator frame to earth ground.
Oil Fill  Fill engine with oil here. See page 5 for oil
requirements.
KNOW YOUR GENERATOR
Read this owners manual and safety rules before operating your generator.
Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
Circuit Breakers (AC)
Fuel Tank
120 Volt AC, 30 Amp
eceptacle
120/240 Volt AC, 20 Amp
eceptacle
120 Volt AC, 20 Amp
Duplex eceptacles
Grounding Wing Nut
Fuel ShutOff
Valve
Oil Fill

Generac Portable Products SVP5000 Generator
5
BEFORE STARTING THE
ENGINE
Add Oil
WARNING! Any attempt to crank or start the
engine before it has been properly filled with
the recommended oil may result in an engine
failure.
To fill your engine with oil:
 Place generator on a level surface.
 Clean area around oil fill and remove oil fill cap.
 Select the oil's viscosity grade and fill engine with oil
following the instructions given in the engine owners
manual. Do Not overfill!
 Install oil fill cap.
NOTE: The generators revolving field rides on a pre-
lubricated and sealed ball bearing that requires no
additional lubrication for the life of the bearing.
Add Gasoline
DANGER! Explosion Hazard! Never fill fuel
tank indoors. Never fill fuel tank when engine is
running or hot. Do Not light a cigarette or
smoke when filling the fuel tank.
WARNING! Do Not overfill the fuel tank.
Always allow room for fuel expansion.
 Use regular UNLEADED gasoline with the
Generator engine. Do Not use premium gasoline.
Do Not mix oil with gasoline.
 Clean area around fuel fill cap, remove cap.
 Add unleaded regular gasoline, slowly to fuel tank.
Be careful not to overfill. Allow about 1/2" of tank
space for fuel expansion (Figure 2).
 Install fuel cap and wipe up any spilled gasoline.
IMPORTANT: It is important to prevent gum deposits
from forming in essential fuel system parts such as the
carburetor, fuel filter, fuel hose or tank during storage.
Also, experience indicates that alcohol-blended fuels
(called gasohol, ethanol or methanol) can attract
moisture which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage.
To avoid engine problems, the fuel system should be
emptied before storage of 30 days or longer. See
Storage on page 10. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
Figure 2  Fill Tank with Fuel

Generac Portable Products SVP5000 Generator
6
OPERATING THE GENERATOR
CAUTION! Never start or stop, the engine with
electrical loads connected to the unit and with
the connected devices turned ON.
Starting the Engine
DANGER! Breathing Hazard! Never run
engine indoors or in enclosed poorly ventilated
areas. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
WARNING! Burn Hazard! Temperature of
muffler and nearby areas may exceed 150°F
(65°C). Avoid these areas.
 Unplug all electrical loads from generator
receptacles before starting the engine.
 Make sure the unit is in a level position.
 Open the fuel shutoff valve (Figure 3).
 Move the choke lever to the Choke position
(Figure 4).
 Set the engine control switch to the On position
(Figure 5).
 Grasp starter grip and pull slowly until you feel some
resistance. Then pull cord out with rapid full arm
stroke. Let rope return slowly. Do Not let rope snap
back against starter.
 When engine starts, move choke lever to Run
position.
NOTE: If engine fails to start after 3 pulls, move the
choke lever to Run and pull starter rope again.
NOTE: If the engine still fails to start, check for proper
oil level in crankcase. Unit is equipped with a low oil
shutdown system. See engine owners manual for
information regarding the low oil shutdown system.
NOTE: If engine fires, but does not continue to run,
move choke lever to Run and repeat starting
instructions.
Connecting Electrical Loads
 Let engine stabilize and warm up for a few minutes
after starting.
 Plug in and turn on the desired 120 and/or 240 Volt
AC, single phase, 60 Hz electrical loads.
Do Not connect 240 Volt loads to the 120 Volt
duplex receptacles.
Do Not connect 3phase loads to the generator.
Do Not connect 50 Hz loads to the generator.
DO NOT OVERLOAD THE GENERATOR. Add up
the rated watts (or amps) of all loads to be
connected at one time. This total should not be
greater than the rated wattage/amperage capacity of
the generator. See Dont Overload the Generator
on page 9.
Figure 3  Fuel ShutOff Valve
Figure 4  Choke Lever
Figure 5  Engine Control Switch

Generac Portable Products SVP5000 Generator
7
Stopping the Engine
 Unplug all electrical loads from generator panel
receptacles. Never start or stop engine with
electrical devices plugged in and turned on.
 Let engine run at no-load for several minutes to
stabilize the internal temperatures of engine and
generator.
 Move engine control switch to the Off position.
 Close the fuel shutoff valve.
COLD WEATHER
OPERATION
Under certain weather conditions (temperatures below
40°F [4°C] and a high dew point), your Generac
generator may experience icing of the carburetor
and/or the crankcase breather system.
In an emergency, use the original shipping box as a
temporary shelter:
 Cut off all flaps.
 Cut out one of the long sides of the box to expose
exhaust side of unit. Ensure a minimum of two feet
clearance between open side of box and nearest
object.
 Cut appropriate slots to access receptacles of unit.
You may also need to cut a clearance slot for the
handle.
 Start unit, then place box over it.
IMPORTANT: emove shelter when temperature is
above 40°F [4°C].
For a more permanent shelter, build a structure that
will enclose three sides and the top of the generator:
 Make sure entire muffler-side of generator is
exposed. A typical shelter is shown in Figure 6.
 Ensure a minimum of two feet clearance between
open side of box and nearest object.
 Face exposed end away from wind and elements.
 Enclosure should hold enough heat created by the
generator to prevent icing problems.
CAUTION! Never run unit indoors; Do Not
enclose generator any more than shown.
emove shelter when temperatures are above
40°F [4°C].
Figure 6  Typical Cold Weather Temporary Shelter
Wind

Generac Portable Products SVP5000 Generator
8
RECEPTACLES
1 0 Volt AC, 0 Amp Duplex
Receptacles
Each of these receptacles is protected against
overload by 20 Amp push-to-reset circuit breaker.
Use each receptacle to operate 120 Volt, 60 Hz, single
phase loads requiring up to 2,400 (2.4kW) watts of
power at 20 Amps of current (Figure 7).
1 0/ 40 Volt AC, 0 Amp Locking
Receptacle
Use a NEMA L14-20P plug with this receptacle.
Connect a 4-wire cord set rated for 250 Volt loads at
20 AC Amps (or greater) (Figure 8). You can use the
same 4-wire cord if you plan only to run a 120 Volt
load.
This receptacle powers 120/240 Volt AC, 60 Hz, single
phase loads and is protected by a 20 Amp push-to-
reset circuit breaker.
1 0 Volt AC, 30 Amp Locking
Receptacle
Use a NEMA L5-30P plug with this receptacle.
Connect a 3-wire cord set rated for 125 Volt AC loads
at 30 Amps to the plug (Figure 9).
Use this receptacle to operate 120 Volt AC, 60 Hz,
single phase loads requiring up to 3,600 watts
(3.6 kW) of power at 30 Amps. The outlet is protected
by a 30 Amp push-to-reset circuit breaker.
Figure 9  120 Volt, 30 Amp Locking eceptacle
Figure 7  120 Volt, 20 Amp Duplex eceptacle
Figure 8  120/240 Volt, 20 Amp Locking eceptacle

Generac Portable Products SVP5000 Generator
9
DONT OVERLOAD THE
GENERATOR
Overloading a generator in excess of its rated wattage
capacity can result in damage to generator and to
connected electrical devices. Observe the following, to
prevent overloading the unit:
 Add up the total wattage of all electrical devices to
be connected at one time. This total should NOT be
greater than the generators wattage capacity.
 The rated wattage of lights can be taken from light
bulbs. The rated wattage of tools, appliances and
motors can usually be found on a data plate or decal
affixed to the device.
 If the appliance, tool or motor does not give wattage,
multiply 120 Volts times ampere rating to determine
watts (volts x amps = watts).
 Some electric motors, such as induction types,
require about three times more watts of power for
starting than for running. This surge of power lasts
for only a few seconds when starting such motors.
Be sure you allow for this high starting wattage
when selecting electrical devices to connect to your
generator. First figure the watts needed to start the
largest motor. Add to that figure the running watts of
all other connected loads.
 Devices in the wattage reference guide (Figure 10)
are provided to help you to determine how many
items the generator can operate at one time.
Recreational/Home Uses
Tool/Appliance...................................................Watts
AM/FM clock radio....................................................50
Light bulb................................................................100
Fan .........................................................................200
20" color TV............................................................400
*Deep freezer .........................................................500
Personal computer and 15" monitor .......................800
*1/3 hp furnace fan blower......................................800
Microwave oven......................................................800
*18 cu ft refrigerator................................................800
Sump pump ..........................................................1000
Electric skillet........................................................1250
*½ hp water well pump .........................................1400
*12,000 Btu window air conditioner ......................1400
Space heater ........................................................1800
Electric water heater.............................................4000
Professional/Contractor Uses
Tool/Appliance...................................................Watts
*1/3 hp airless sprayer............................................600
3/8" hammer drill.....................................................600
Variable speed Sawzall®........................................960
½" power drill........................................................1000
Quartz-halogen work light.....................................1000
Belt sander ...........................................................1200
7 ¼" circular saw ..................................................1500
7 ¼" worm drive saw ............................................1600
*1½ hp air compressor .........................................1800
*10" power miter saw............................................1800
6" bench grinder ...................................................1800
*6" table planer .....................................................1800
*10" table/radial arm saw......................................2000
Wire feed welder...................................................2400
* allow 3 times listed watts for starting this device
Figure 10  Wattage eference Guide

Generac Portable Products SVP5000 Generator
10
SPECIFICATIONS
Maximum Surge Watts . . . . . . . . . . .6,250 watts
Continuous Wattage Capacity . . . . . .5,000 watts
Power Factor . . . . . . . . . . . . . . . . . .1.0
ated Maximum Continuous Load
At 120 Volts . . . . . . . . . . . . . . . . .41.7 Amps
At 240 Volts . . . . . . . . . . . . . . . . .20.8 Amps
Phase . . . . . . . . . . . . . . . . . . . . . . .1 phase
ated Frequency . . . . . . . . . . . . . . .60 Hertz
Fuel Tank Capacity . . . . . . . . . . . . . .5 U.S. gallons
GENERAL MAINTENANCE
RECOMMENDATIONS
The owner/operator is responsible for making sure
that all periodic maintenance tasks are completed on a
timely basis; that all discrepancies are corrected; and
that the unit is kept clean and properly stored. Never
operate a damaged or defective generator.
Engine Maintenance
See engine manual for instructions.
Generator Maintenance
Generator maintenance consists of keeping the unit
clean and dry. Operate and store the unit in a clean
dry environment where it will not be exposed to
excessive dust, dirt, moisture or any corrosive vapors.
Cooling air slots in the generator must not become
clogged with snow, leaves or any other foreign
material.
NOTE: Do Not use a garden hose to clean generator.
Water can enter engine fuel system and cause
problems. In addition, if water enters generator
through cooling air slots, some of the water will be
retained in voids and cracks of the rotor and stator
winding insulation. Water and dirt buildup on the
generator internal windings will eventually decrease
the insulation resistance of these windings.
To Clean the Generator
 Use a damp cloth to wipe exterior surfaces clean.
 Soft, bristle brush may be used to loosen caked on
dirt or oil.
 A vacuum cleaner may be used to pick up loose dirt
and debris.
 Low pressure air (not to exceed 25 psi) may be
used to blow away dirt. Inspect cooling air slots and
opening on generator. These openings must be kept
clean and unobstructed.
STORAGE INSTRUCTIONS
The generator should be started at least once every
seven days and allowed to run at least 30 minutes. If
this cannot be done and you must store the unit for
more than 30 days, use the following guidelines to
prepare it for storage.
Generator Storage
 Clean the generator as outlined in To Clean the
Generator.
 Check that cooling air slots and openings on
generator are open and unobstructed.
DANGER! Storage covers can be flammable.
Do Not place a storage cover over a hot
generator. Let the unit cool for a sufficient time
before placing the cover on the unit.
Engine Storage
See engine owners manual for instructions.
Other Storage Tips
Do Not store gasoline from one season to another.
 eplace your gasoline can if it starts to rust. ust
and/or dirt in a gasoline can cause problems when
you use contaminated fuel with this unit.
 Store in clean and dry area.

Generac Portable Products SVP5000 Generator
11
TROUBLESHOOTING
Problem Cause Solution
Engine is running, but
no AC output is
available.
1. Circuit breaker is open.
2. Poor connection or defective cord
set.
3. Connected device is bad.
4. Fault in generator.
1. eset circuit breaker.
2. Check and repair.
3. Connect another device that is in good
condition.
4. Contact Generac service facility.
Engine runs good but
bogs down when loads
are connected.
1. Short circuit in a connected load.
2. Generator is overloaded.
3. Engine speed is too slow.
4. Shorted generator circuit.
1. Disconnect shorted electrical load.
2. See Dont Overload the Generator on
page 9.
3. Contact Briggs & Stratton service
facility.
4. Contact Generac service facility.
Engine will not start; or
starts and runs rough.
1. On/Off switch set to Off (o).
2. Dirty air cleaner.
3. Out of gasoline.
4. Stale gasoline.
5. Spark plug wire not connected to
spark plug.
6. Bad spark plug.
7. Water in gasoline.
8. Overchoking.
9. Low oil level.
10. Excessively rich fuel mixture.
11. Intake valve stuck open or closed.
12. Engine has lost compression.
1. Set switch to On ().
2. Clean or replace air cleaner.
3. Fill fuel tank.
4. Drain gas tank and fill with fresh fuel.
5. Connect wire to spark plug.
6. eplace spark plug.
7. Drain gas tank; fill with fresh fuel.
8. Put choke lever to Run position.
9. Fill crankcase to proper level.
10. Contact Briggs & Stratton service
facility.
11. Contact Briggs & Stratton service
facility.
12. Contact Briggs & Stratton service
facility.
Engine shuts down
during operation.
1. Out of gasoline.
2. Low oil level.
3. Fault in engine.
1. Fill fuel tank.
2. Fill crankcase to proper level.
3. Contact Briggs & Stratton service
facility.
Engine lacks power.
1. Load is too high.
2. Dirty air filter.
3. Engine needs to be serviced.
1. See Dont Overload the Generator on
page 9.
2. eplace air filter.
3. Contact Briggs & Stratton service
facility.
Engine hunts or
falters.
1. Choke is opened too soon.
2. Carburetor is running too rich or
too lean.
1. Move choke to halfway position until
engine runs smoothly.
2. Contact Briggs & Stratton service
facility.

Generac Portable Products SVP5000 Generator
12
ELECTRICAL SCHEMATIC

Generac Portable Products SVP5000 Generator
13
WIRING DIAGRAM

Generac Portable Products SVP5000 Generator
14
EXPLODED VIEW  GENERATOR

Generac Portable Products SVP5000 Generator
15
Item Part # Qty Description
1 NSP 1 ENGINE, B & S 10 H.P.
2 66825C 1 CA IE , ear Bearing
3 91825 1 ASSY., Brush & Bridge
ectifier
4 66365-G 1 HOUSING, Engine Adapter
5 22129 2 WASHE , M8 - 5/16 Lock
6 86307 4 HHMS, 5/16" x 3/4"
7 91844J 1 ASSEMBLY, otor
8 65791 1 BEA ING
9 96796 1 WASHE , Special
10 47480 1 HHCS, 5/16" - 24 x 7"
11 91859J 1 ASSEMBLY, Stator
12 81917 1 PIN, M4 x 10 oll
13 86308C 4 HHCS, M6 - 1.0 x 130
14 48031C 2 CLAMP, Hose 1/4"
15 88977 1 SWITCH, Low Oil Shutdown
16 70642 2 MOUNT, Vibration 45 Deg.
17 B4871 1 COVE , Bearing Carrier
18 52858 6 NUT, M8 Locking 1.25 Flange
19 76222 2 PPHMS, M8 1.25 x 40 mm
20 14353621 1 WI E, Ground
21 82881 3 LOCK WASHE , Internal
22 86292 5 SC EW, #10 Self Drilling
23 38150 6 FLAT WASHE , #8
24 23365 6 LOCK WASHE , No. 8
serrated
25 B4465 1 DECAL, Control Panel
26 B78951A 1 SHIELD, Heat
27 56893 2 SC EW 10 - 24 x 1/2"
Crimptite
28 77374 1 TANK, Plastic 5 Gal.
29 23365 1 WASHE , No. 8 Shakeproof
30 78831B 4 CAPSC, M6 x 60 mm Hx Hd
31 90878 1 CAP, Fuel
32 77395 4 NUT, M6 Flange Lock
33 78299 1 BUSHING, Plastic Tank
34 80270 1 VALVE, Plastic Tank
35 81898 1 PANEL, Control
Item Part # Qty Description
36 81919 1 COVE , ear Panel
37 68868 1 OUTLET, 120 Volt 30Amp.
Locking ec.
38 68867 1 OUTLET, 120/240 Locking
ec.
39 68759 1 OUTLET, 120 Volt 20Amp
Duplex
40 84242 2 G OMMET, . B. C.
41 25244 2 NUT, 5/16 - 18 Hex
42 74908 4 TAPTITE, M5 0.8 x 10
43 22264 6 LOCK WASHE , #8
44 51715 6 NUT, Hex M4 - 0.7
45 75207A 1 CI CUIT B EAKE , 30 Amp
46 75207 2 CI CUIT B EAKE , 20 Amp
47 26850 2 WASHE , Shakeproof 1/4"
48 75475 6 PPHMS, M4 - 0.7 x 10
49 82857 2 MOUNT, ubber
50 82308 6 SC EW, Self Tapping
51 86494 1 WING SC EW, M6 x 16
53 A91020 1 C ADLE
54 67022 1 G OMMET, ubber
55 22471 2 NUT, No. 8-32
56 22769 1 WASHE , Shakeproof #10
57 66849 2 SC EW, M5 - 0.8 x 15
58 91842A 1 WI E, LOS
59 22695 1 6-Pin Connector - Male
60 22694 1 6-Pin Connector
61 32713 1 SC EW, No. 10-32 x 5/8"
62 91841 1 GASKET, LOS
63 83465 4 G OMMET, Mounting Tank
64 B4986 1 DECAL, Ground
65 B2153 4 SC EW, Self Driller #12-14 x
7/8"
Accessories Not Illustrated
37806 120 Volt, 30 Amp Plug
43483 120/240 Volt, 20 Amp Plug
PARTS LIST  GENERATOR

LIMITED WARRANTY
FOR PORTABLE GENERATORS
(EXCEPT GN ENGINE SERIES)
Generac Portable Products (hereafter referred to as the COMPANY) warrants to the original purchaser that its
generator will be free from defects in materials or workmanship for a period of one year* from the date of original
purchase. This warranty does not apply to units used for prime power in place of utility. This warranty does not
include the gasoline engine when furnished or attached because such engine is covered solely by the warranty of
the manufacturer of the engine. Starting batteries are not warranted by the COMPANY.
*NOTE: ental units, demonstrators, commercial applications, such as construction or income producing, are
warranted for 90 days. ental units, demonstrators, or commercial applications such as construction or utility
which are resold are not covered under warranty by the COMPANY. Any warranty, whether expressed or implied,
rests solely with the seller.
During said warranty period, the COMPANY will, at its option, repair or replace any part which, upon examination
by the COMPANY is found to be defective under normal use and service. All transportation costs under warranty,
including return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser. This
warranty does not include nominal maintenance and service and does not apply to a generator set, or parts,
which have been subjected to improper or unauthorized installation, misuse, negligence, accident, overloading,
overspeeding, improper maintenance, repair or storage so as, in the COMPANY's judgment, to adversely affect
its performance and reliability.
THE E IS NO OTHE EXP ESS WA ANTY. THE COMPANY HE EBY DISCLAIMS ANY AND
ALL IMPLIED WA ANTIES, INCLUDING BUT NOT LIMITED TO THOSE OF ME CHANTABILITY
AND FITNESS FO A PA TICULA PU POSE TO THE EXTENT PE MITTED BY LAW. THE
DU ATION OF ANY IMPLIED WA ANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO
THE TIME PE IOD AS SPECIFIED IN THE EXP ESS WA ANTY. LIABILITY FO INCIDENTAL,
CONSEQUENTIAL, O SPECIAL DAMAGES UNDE ANY AND ALL WA ANTIES IS
EXCLUDED TO THE EXTENT PE MITTED BY LAW. THE COMPANY ALSO DISCLAIMS ANY
ESPONSIBILITY FO INCIDENTAL O CONSEQUENTIAL DAMAGES SUCH AS THE LOSS OF
TIME O THE USE OF THE POWE EQUIPMENT, O ANY COMME CIAL LOSS DUE TO THE
FAILU E OF THE EQUIPMENT; AND ANY IMPLIED WA ANTIES A E LIMITED TO THE
DU ATION OF THIS W ITTEN WA ANTY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusions or limitations of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other rights, which vary from state to state.
This warranty is effective for all products manufactured after June, 1998, and supersedes all prior warranties of
the COMPANY.
For service, contact your nearest COMPANY authorized warranty service facility or call 1-877-544-0982.
Warranty service can only be performed by a COMPANY authorized service facility. At the time of requesting
warranty service, evidence of original purchase date must be presented.
GENERAC PORTABLE PRODUCTS
Jefferson, Wisconsin 53549