General MMD900 User manual

PIN/PINLESS DEEP SENSING
MOISTURE METER
WITH REMOTE PROBE
USER’S MANUAL
MMD900
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 –4
Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
What’s in the Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setup Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Install Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 –9
Measuring Moisture Levels . . . . . . . . . . . . . . . . . . 6 –7
Advanced Setup Instructions . . . . . . . . . . . . . . . . 7 –8
Checking Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Return for Repair Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Manuel de L'Utilisateur . . . . . . . . . . . . . . . . . . . . . . . . . . 12 – 22
Manual del Usuario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 – 32
2

3
INTRODUCTION
Thank you for purchasing eneral Tools & Instruments’ MMD900 Pin/Pinless
Deep Sensing Moisture Meter with Remote Probe. Please read this user’s
manual carefully and thoroughly before using the meter.
The MMD900 is designed for use in woodworking, water damage restoration,
building construction and home renovation. Examples include:
• Checking for moisture on or below the surface of carpets and sub-flooring
• Measuring the surface moisture content of wood or drywall before painting,
wallpapering, sealing or treating
• Locating water leaks above ceilings, below floors or behind walls
• Selecting dry lumber
WHICH SENSOR SHOULD YOU USE?
MMD900 is equipped with a pinless sensor and a pin sensor. The pinless
(capacitive) sensor is the only choice for estimating the surface or internal
moisture level of materials like finished wood, paint or wallpaper that cannot be
marred by pinholes. If accurate readings are important, the pin sensor is the
only option because the pinless sensor can only provide relative readings.
The distinction between absolute and relative readings is important to
understand. The moisture level measurements made by either pair of test
pins—on the instrument or on the remote probe—are displayed in units of
%WME (Wood Moisture Equivalent) simultaneously on a 6.0 to 87.6 count
digital LCD and a 40-LED analog bar graph. Pin measurements are accurate
within 3%.
By contrast, readings made by the pinless sensor are simultaneously displayed
with no units on the LCD and on a second scale (called REL) of the bar graph.
Although the pinless readings have no accuracy specification, they are
nonetheless useful for quickly comparing the moisture levels of materials, or
the wetness of different areas of the same material. Two possible uses for the
relative readings are:
1. Determining whether two pieces of wood to be joined have roughly the
same moisture content (which means they will dry out at the same rate
without warping).
2. Locating the source of a water leak above a ceiling, by comparing the
REL readings at various points on it. If the ceiling is level, the point with
the highest REL reading is below the source of the leak.

The biggest advantage of the pinless sensor is its ability to sense moisture up
to 2 in. below or behind the surface of a material. The stainless steel test pins
of the MMD900 can also sense moisture just below the surface of some
materials. However, for hard materials like wood, measurements made by the
meter’s test pins mostly represent surface moisture content.
For softer materials like soil, paper or powders, pin measurements are more
likely to reflect the average moisture level of the material between its surface
and the penetration depth of the pins (usually far less than 0.6 or 0.4 in.).
KEY FEATURES
• Two measurement modes: Pin (conductivity-based) and pinless
(based on the fringing field effect)
• Two sets of test pins: on top of the meter and at the end of 46 in. remote
cable
• Pin measurement accuracy of ±3% in pin measurement mode
• Pinless mode measurement depth of 2 in. below surface
• Displays %WME and relative readings simultaneously on two displays:
0 to 99.9 count jumbo LCD with 0.9 in. (23mm) digits, and 40-dot tri-color
LED bar graph
• Manual or automatic calibration checking
• Data hold (display lock or “freeze”) function
• User-programmable beeper function, backlight function and auto power off
time
• Low battery warning
• Includes two pairs of replacement test pins
• Spare pins storage compartment
4

WHAT’S IN THE CASE
The MMD900 comes in a custom molded plastic case along with a remote
pin-type probe and cable, a 9V battery, two pairs of replacement pins and this
user’s manual. An optional deep wall moisture probe ( eneral P/N MP905) is
available.
PRODUCT OVERVIEW
The figure shows all of the controls, indicators and physical features on the
front, bottom, top, back and right side of the MMD900. Familiarize yourself with
their positions and functions before moving on to the Setup Instructions.
A. Calibration check holes
B. Protective cover
C. 15mm replaceable test pins
D. Indicates display is
locked (frozen)
E. Measurement mode indicator
(REL shown)
F. Indicates beeper is
enabled
G. Indicates battery is
weak
H. Sensing area (on back of meter)
I. Jumbo LCD display
J. Five-function Mode button
K. Four-function button
L. Slots for holding protective
cover (on bottom of meter)
M. Battery/spare pins compartment cover (on back of meter)
. Tri-color 40-LED analog bar graph
O. Remote probe with 10mm test pins (shown with protective cap on)
P. Jack for remote probe
5
%WME
30
40
55
6
8
10
12
14
16
18
20
30
40
50
60
70
90
0
3
6
9
15
18
21
0
65
75
85
REL
PinSense
S
E
T
C
A
L
CAL
%WME
REL
B.L.
SET
H
O
D
L
I
G
H
F
E
C
D
J
BA
P
N
M
L
K

SETUP INSTRUCTIONS
INSTALL BATTERY
To open the battery/spare pins compartment, turn the meter over and use your
thumb to slide the compartment cover (Callout M of the figure) down and away
from the unit.
OPERATING INSTRUCTIONS
To power on the meter, press the button and hold it for at least three
seconds. (To power off the meter, follow the same instruction.)
By factory default:
• The beeper is enabled, and beeps faster the higher the readout above
17%WME in pin measurement mode (17 in REL mode).
• The auto power off function is enabled, and activated by 3 minutes of front-
panel inactivity.
• The backlight is on.
• Manual calibration checking (see p. 9) is enabled.
To change any default , follow the Advanced Setup Instructions beginning on p. 7.
MEASURING MOISTURE LEVELS
Surface moisture levels should be measured by the test pins if the surface
being tested can tolerate pinholes. If it cannot, use the meter’s pinless sensor.
Internal moisture levels can be gauged by the pinless sensor for comparison
purposes.
To use the remote probe, remove the small rubber yellow plug from the jack
on the right side of the meter (callout P of the figure). Then insert the white plug
at the end of the cable into the jack.
To make a surface moisture level measurement, press the Mode button as
many times as necessary until the text “%WME” appears on the top line of the
LCD. Then press the test pins of the meter or the remote probe against the
target material. The material’s surface moisture level will be displayed as a
percentage on both the LCD and the LED bar graph.
The bar graph uses LEDs of three different colors (green, yellow and red) to
indicate different moisture level ranges (low, medium and high, respectively).
Readings below 17% are considered low, readings between 17% and 30%
medium, and readings above 30% high. If the beeper is enabled with the
factory-default setting, it will beep faster the higher the moisture level rises
above 17%.
6

To gauge the internal or surface moisture level of a material, enter REL
mode by pressing the Mode button as many times as necessary until the text
REL appears on the top line of the LCD. To establish a baseline for relative
readings, press the area of the back cover marked “Pinless Sensor” against a
material known to be completely dry. The meter should read “0” on both the
LCD and LED bar graphs. Then press the back of the meter against one or more
points on the target surface and compare the readings.
Some measurement tips:
1. For best results, press the pinless sensor against a flat area of the target
material.
2. When holding the sensor against a material, keep your hand and fingers as
far away from the sensing area as possible.
3. The dimensions of the target surface should be at least as large as those of
the sensing area: 1.6 x 1.6 in. (40 x 40mm).
4. Never use force to drive the test pins into a hard surface.
5. Measurements of wood are skewed by two variables: ambient humidity and
the density of the wood species. Please be aware of the effect of these
variables.
To scan a material for an area of peak wetness in either measurement
mode (%WME or REL), first make sure that the beeper is enabled (indicated by
the icon on the top line of the LCD). If the icon is present, scan the
material while paying attention to the beeper’s frequency. The faster the beeper
beeps, the wetter an area is. Near the high end of the meter’s measurement
range, the beeping sounds almost constant.
If the beeper has been disabled, to re-enable it you must power off the meter
and then change the beeper’s default setting using the Advanced Setup
instructions in the next section.
To hold a measurement, press the button briefly. The display will “freeze”
with the held value, along with a (lock) icon at upper right. To unlock the
display, press the button briefly again.
ADVANCED SETUP INSTRUCTIONS
In Setup mode, you can change the default settings for the meter’s beeper,
backlight, auto power off and calibration check functions.
To enter Setup mode, power off the meter by pressing the button and
holding it for at least three seconds. Then power the meter back on in a special
7

way by simultaneously pressing the and Mode buttons and holding them for
at least three seconds. Doing this will cause the beeper to sound, the backlight
to come on and the word “SEtUP” to scroll across the LCD.
After a few seconds, the LCD will read out “0 = 0”. In this format, the left digit
represents the Option No. and the right digit stands for the current setting for
that option. For example, “0 = 0” is shorthand for Option 0, Setting 0.
The table below details the five function options available to you in Setup
mode.
Function Option o. Setting Action
(Left Digit) (Right Digit)
Default 0 0 Loads factory default settings
Settings 1 Loads user’s default settings
Source Backlight comes on for 30 seconds
Beeper 1 0 Programs beeper to beep faster the higher the
moisture level above 17%WME (17 in REL mode)
1 Programs beeper to beep faster the higher the
moisture level
2 Programs beeper to sound when switching
between measurement modes
3 Disables beeper. Removes icon from display
Auto power 2 0 Disables auto power off function
off 1 Sets auto power off interval to 3 minutes
2 Sets auto power off interval to 5 minutes
3 Sets auto power off interval to 10 minutes
Backlight 3 0 Disables display backlight
1 Enables display backlight
Calibration 4 0 Enables manual calibration checking by user
Check 1 Programs meter automatically check calibration
following power on
The factory default setting for all five functions—including the source of the
default settings—is 0.
To change any or all settings to your choice(s), you must first change the
setting of Option 0 from 0 to 1. Opportunities to change the settings of the other
four functions from their factory defaults are then made available in order, from
Option 0 to Option 4. As each Option is presented, you can change its setting or
leave the existing setting unchanged. In either case, you must confirm (save)
8

the setting to allow the sequence to continue.
It’s important to understand that in Setup mode you have 30 seconds to
confirm the setting of each Option. If you take longer than 30 seconds to
confirm any setting, the MMD900 will automatically exit Setup mode and enter
Measurement mode.
To change any setting, use the Mode button to cycle through the choices
(0 or 1 for Options 0, 3 and 4; 0, 1, 2 or 3 for Options 1 and 2). When the setting
you want appears as the right digit on the display, press the button to save
it. Each time you save a setting, the display advances to the next Option. To
leave a setting unchanged, press the button to advance to the next Option.
Once a setting has been chosen for Option 4, the meter will automatically exit
Setup mode and enter Measurement mode. You cannot access the Options out
of sequence. For example, if you have disabled the beeper (by pressing the
button with “1 = 3” on the display), you cannot re-enable the beeper without
powering off the meter and re-entering Setup mode.
The one exception to this rule is the setting of the display backlight. You can
turn the backlight on or off by pressing the Mode button and holding it for at
least three seconds.
CHECKING CALIBRATION
Option 4 gives you two choices for checking the calibration of the meter.
Choosing Setting 0 lets you check the calibration manually. Setting 1
automatically checks the calibration of the meter each time it is powered on.
To check the meter’s calibration manually, press the and Mode buttons
at the same time while operating in %WME measurement mode. This will
cause the text “CAL” to flash twice on the display and the beeper to sound
twice. Remove the protective cap from the top of the meter, taking care not to
stab yourself with the two sharp test pins beneath it. Then flip the cap over and
place the two holes in its top over the meter’s two test pins. The display should
read 18.2% ±(3% of reading + 5 digits) in pin measurement mode.
If the calibration check produces a reading higher than 21.7% or lower than
15.7%, and the meter is still under warranty, call eneral's Customer Service
Department at 212-431-6100 to arrange to return the meter for service or
replacement.
9

SPECIFICATIONS
Measurement Ranges 6.0 to 87.6% WME and 0.1 to 99 REL
Measurement Accuracy ±3% in pin mode
Length of Test Pins 15mm (0.6 in.) on top of meter; 10mm (0.4 in.) on
remote probe; 10mm and 15mm (spares)
Length of Remote Cable 46 in. (1.168m)
Measurement Depth (pinless mode) 2 in. (51mm)
Pinless Sensing Area 1.6 x 1.6 in. (40 x 40mm)
LCD Range/Size 6.0 to 87.6 count with 0.9 in. (23mm) high digits
LCD Resolution 0.1%
Bar Graph Composition 40 LEDs of 3 colors: green (0 to17%), yellow
(17 to 30%) and red (>30%)
Bar Graph Resolution ±1 LED (±2.5%)
Auto Power Off After 3, 5 or 10 minutes (user selectable) with
0% reading
Low Battery Warning Level <6.5VDC
Current Consumption <70mADC
Calibration Point 18.2%
Operating Temperature 32° to 122°F (0° to 50°C) @<80% relative humidity
Dimensions 9 x 2.75 x 1.625 in. (229 x 70 x 41mm)
Weight 8 oz. (249g)
Power Source 9V battery (included)
MAINTENANCE TIPS
When the icon appears at the upper left of the LCD, it’s time to replace
the 9V battery that powers the meter (although measurements will remain valid
for several hours after the icon first appears).
When the tips of the meter’s factory-installed 15mm test pins, or the tips of the
10mm factory-installed test pins on the remote probe show signs of wear,
replace them with a pair of 10mm or 15mm pins included in the case.
Remove the battery when storing the meter for an extended period of time.
Never drop or disassemble the meter or immerse it in water.
10