GENERI SR-2400RB-US User manual

Designation DALI MCU
Power connection L, N AC mains
Operating voaltage 100-240V AC
Power consumption 2.3W max.
DALI connection Da+/Da-, max. 300m cable length, DALI
power supply output current max 100mA.
Perm. Cable cross-section 0.5…1.5 mm2
Ambient temperature 0…+50 °C
Type of protection IP 20
Protection class II
Function introduction
Important: Read All Instructions Prior to Installation
Product Data
Dimensions 75x120x53mm
Back side
Rotate the knob counterclockwise
to decrease light intensity from
100% to 1%.
Rotate the knob clockwise to
increase light intensity
from 1% to 100%
Click the rotary knob
to switch ON/OFF light
Front side
N
DALI Dimmer
LDA-DA+
DALI OUTPUT AC INPUT
31.20 mm
AC Power input
DALI signal output
49 mm
48.44 mm
83.00 mm 120.0 mm
75.0 mm
DALI MCU digital rotary dimmer 09.2400RBU.04757
• Each control circuit can supply DALI power for as many as 50 DALI devices
• The lighting system responds immediately and harmoniously when the brightness level is changed at either of
the control devices.
• All that while allowing for the required comfortable, easy and complete control over the lighting levels at any
time.
• Innovative Function to Power DALI Bus While Connected to AC Mains
• Powered by DALI Bus while not Connected to AC Mains
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
Operation
This device is a DALI MCU with built-in DALI bus power supply which can power DALI bus while connected with
100-240VAC mains. It also can be powered by DALI bus while not connected with AC mains.
There can be up to only 2 MCUs connect to AC 220V mains, the other MCUs powered by DALI bus.
Each control circuit simultaneously affords the integration of as many as 100 DALI ECG and of up to 4 DALI
MCU control devices (control points).
Switch ON/OFF
Click the rotary knob to switch ON/OFF light.
Increase/Decrease Light Intensity
Rotate the knob clockwise to increase light intensity from 1% to 100%, rotate the knob counterclockwise to
decrease light intensity from 100% to 1%.
Set the minimum brightness value
Press and hold down the knob over 5 seconds until the light flashes, to set the current brightness value as the
minimum brightness value for dimming, it is dimmable from this minimum brightness value to 100%.
Delete the minimum brightness value setting
Click the knob to switch off the light first, then press and hold down the knob over 5 seconds until the light
flashes, the minimum brightness value will be deleted. It is dimmable from 1% to 100% then.

Installation Figure 1: Wiring scheme with 2 MCUs powered by AC mains to control up to 100 DALI ECG
Figure 2: Wiring scheme to control up to 50 DALI ECG
DA- DA+ L N
Control point 1
Control point 2
AC mains
Wiring diagram
DALI DT6 Device
DALI DT6 Device
DA
DA
DA
DA
1. To control up to 100 ECG with the setup (Figure 2), there
are 2 panels connected to AC mains.
2. To control up to 50 ECG with the setup (Figure 1), there is
only 1 panel connected to AC mains. Other panels are
powered by DALI bus. Max. 2 DALI panels can be connected
to AC mains in the same control circuit.
DA- DA+ L N
Control point 1
Control point 2
Control point 3
AC mains
DALI DT6 Device
DALI DT6 Device
DALI DT6 Device
DA
DA
DA
DA
DA
DA