Genexis FiberTwist G2110 User manual

G
FiberTwist–Series
Installation Guide

Buton oveview Pot oveview
Power pot
ONOFF
buton
LAN pot
Reset
buton
Unlock buton
Remove FiberTwist or Blind Cover – press and
hold while wisting counterclockwise
ONOFF buton
Power ON or OFF – press and
release to switch device ON or OFF
Reset buton (recessed)
Reset – press and release
LED dim buton
Dim LEDs – press and release to dim LEDs in
steps

System
Green – system ok
Green (blinking) – booting
O – power o
Uplink
Green – link ok
Green (blinking) – link establishing
O – no link
Optical signal
Red – no optical signal
O – optical signal ok
LED oveview
LAN
Green – LAN pot connected, no traic
Green (blinking) – LAN pot connected, traic ongoing
O – LAN pot not connected

Box contents
• Genexis FiberTwist (active device)
• Power adapter
• Label (self-adhesive)
• Installation Guide (this document)
Label position
The product label is positioned on the
back of the active device.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Impotant: Instructions need
to be followed precisely and
uninterrupted. This minimizes
the risk of damage to the iber
optic connectors, causing a severe
degradation of signal qualiy.
Dierent language versions of this document and additional product information
are availableon htps:genexis.euproductibewistdownloads
Installation guide
Remove Blind Cover (if present)
. Press and hold the unlock buton (see buton oveview).
. Rotate the Blind Cover counterclockwise till it blocks.
. Remove the Blind Cover from the baseplate (FTU) by pulling
it towards yourself.
. Store the Blind Cover in a safe place.

Remove dust cap
. Take the FiberTwist out of the box.
. The dust cap is connected to the red string
located on the rear of the FiberTwist.
. Remove the dust cap by pulling the red string.
. Store the dust cap in a safe place.
Twist!
. Place the FiberTwist on the FTU as shown in the picture below,
in a –degree angle.
. Rotate clockwise until it clicks into place.
. Make sure the FiberTwist is aligned squarely on the FTU,
each edge must line up directly with the FTU below.
Your FiberTwist is now installed!

Company Name
Genexis B.V.
Company Address
Lodewijkstraat a
 AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis B.V. declares that the product FiberTwist-G is in compliance
with Directives EU, EU, EU, Delegated Directive
 and Ecodesign Directive EC.
The full text of the EU declaration of conformiy is available at the following
internet address: htps:genexis.euredt-G
EU Declaration of Conformiy
Connecting the FiberTwist
. If required, connect your personal devices to the LAN pots via an RJ
nework cable.
. Connect the supplied power adapter to the FiberTwist and plug the adapter
into a power socket.
. Press the ONOFF buton to power on the device.
Warning: The FiberTwist is a Class  laser product.
If at some point in the future it becomes necessay to uninstall the FiberTwist,
please place the Blind Cover back on the FTU immediately and put the dust cap
back on the FiberTwist.

Revision . - June  - Copyright ©  Genexis Netherlands B.V. All rights reseved.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves
the right to change, modify, transfer, or othewise revise this publication without notice.