Genexis FiberTwist Series User manual

XGS2120
FiberTwist-Series
Installation Guide

Button overview Port overview
Power port
ON/OFF
buon
LAN port
ON/OFF buon
Power ON or OFF – press and
release to switch device ON or OFF
Unlock buon
Remove FiberTwist or Blind Cover – press and
hold while twisting counterclockwise
Reset buon (recessed)
Reset – press and release
LED dim buon
Dim LEDs – press and release to dim LEDs
in steps
TV port

System
Green – system ok
Green (blinking) – booting / rmware download
O – power o
Uplink
Green – link ok
Green (blinking) – link establishing
O – no link
LED overview
TV
Green – TV ok
Green (blinking) – insuicient input signal
O – no TV

Box contents
• Genexis FiberTwist (active device)
• Power adapter
• 2x Spare device label (self-adhesive)
Label position
The product label is positioned on the
back of the active device.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Important: Instructions need to be
followed precisely and uninterrupted.
This minimizes the risk of damage to
the ber optic connectors, causing a
severe degradation of signal quality.
Remove Blind Cover (if present)
1. Press and hold the unlock buon (see buon overview).
2. Rotate the Blind Cover counterclockwise till it blocks.
3. Remove the Blind Cover from the baseplate (FTU) by pulling
it towards yourself.
4. Store the Blind Cover in a safe place.
Installation guide

Remove dust cap
1. Take the FiberTwist out of the box.
2. The dust cap is connected to the red string
located on the rear of the FiberTwist.
3. Remove the dust cap by pulling the red string.
4. Store the dust cap in a safe place.
Twist!
1. Place the FiberTwist on the FTU as shown in the picture below,
in a 30–degree angle.
2. Rotate clockwise until it clicks into place.
3. Make sure the FiberTwist is aligned squarely on the FTU,
each edge must line up directly with the FTU below.
Your FiberTwist is now installed!

Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven 2023-03-22
The Netherlands
Hereby, Genexis Netherlands B.V. declares that the product FiberTwist-XGS2120 is in
compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, Delegated Directive
2015/863 and Ecodesign Directive 2009/125/EC.
The full text of the EU declaration of conformity is available at the following internet
address: hps://genexis.eu/product/bertwist/red/bertwist-xgs2120
EU Declaration of ConformityConnecting the FiberTwist
1. If required, connect your television / set-top box to the TV port with a coax cable.
2. If required, connect your personal device to the LAN port via an
RJ45 network cable.
3. Connect the supplied power adapter to the FiberTwist and plug the adapter into
a power socket.
4. Press the ON/OFF buon to power on the device.
Warning: This product contains a laser that emits
invisible light. It is a Class 1 Laser product, which
means it is safe under all conditions of normal use.
However, it is still advised to not look directly into
the ber connector when the product is powered on.
Warning: Do not cover the device, this will
interfere with the ventilation. Ambient Operating
Temperature: 0°C ~ 40°C
If at some point in the future it becomes necessary to uninstall the FiberTwist, please
place the Blind Cover back on the FTU immediately and put the dust cap back
on the FiberTwist.

Revision 1.0 - March 2023 - Copyright ©2023 Genexis Netherlands B.V. All rights reserved.
Multiple languages of this document and additional product information are availableon
hps://genexis.eu/product/bertwist/downloads
Genexis assumes no responsibility for any inaccuracies in this document. Genexis reserves the right to change,
modify, transfer, or otherwise revise this publication without notice.